diff mbox series

[2/5] thermal: int340x: processor_thermal: Support power floor notifications

Message ID 20230926225813.995948-3-srinivas.pandruvada@linux.intel.com
State Superseded
Headers show
Series thermal: processor_thermal: Power floor status | expand

Commit Message

Srinivas Pandruvada Sept. 26, 2023, 10:58 p.m. UTC
When the hardware reduces the power to the minimum possible, the power
floor is notified via an interrupt. This can happen when user space
requests a power limit via powercap RAPL interface, which forces the
system to enter to the lowest power. This power floor indication can
be used as a hint to resort to other methods of reducing power than
via RAPL power limit.

Before power floor status can be read or get notifications from the
firmware, it needs to be configured via a mailbox command. Actual power
floor status is read via bit 39 of MMIO offset 0x5B18 of the processor
thermal PCI device.

To show the current power floor status and get notification
on a sysfs attribute, add additional attributes to
/sys/bus/pci/devices/0000\:00\:04.0/power_limits/

power_floor_enable : This attribute is present when a SoC supports
power floor notification. This attribute allows to enable/disable
power floor notifications.

power_floor_status : This attribute is present when a SoC supports
power floor notification. When enabled this shows the current
status of power floor.

The power floor implementation provides interfaces, which are called
from the sysfs callbacks to enable/disable and read power floor
status. Also provides two additional interface to check if the current
processor thermal device interrupt is for power floor status and
send notification to user space.

Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
---
 .../driver-api/thermal/intel_dptf.rst         |   8 ++
 .../thermal/intel/int340x_thermal/Makefile    |   1 +
 .../processor_thermal_device.c                |  68 ++++++++++-
 .../processor_thermal_device.h                |   8 ++
 .../processor_thermal_power_floor.c           | 114 ++++++++++++++++++
 5 files changed, 198 insertions(+), 1 deletion(-)
 create mode 100644 drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c

Comments

Rafael J. Wysocki Oct. 2, 2023, 6:41 p.m. UTC | #1
On Wed, Sep 27, 2023 at 12:58 AM Srinivas Pandruvada
<srinivas.pandruvada@linux.intel.com> wrote:
>
> When the hardware reduces the power to the minimum possible, the power
> floor is notified via an interrupt. This can happen when user space
> requests a power limit via powercap RAPL interface, which forces the
> system to enter to the lowest power. This power floor indication can
> be used as a hint to resort to other methods of reducing power than
> via RAPL power limit.
>
> Before power floor status can be read or get notifications from the
> firmware, it needs to be configured via a mailbox command. Actual power
> floor status is read via bit 39 of MMIO offset 0x5B18 of the processor
> thermal PCI device.
>
> To show the current power floor status and get notification
> on a sysfs attribute, add additional attributes to
> /sys/bus/pci/devices/0000\:00\:04.0/power_limits/
>
> power_floor_enable : This attribute is present when a SoC supports
> power floor notification. This attribute allows to enable/disable
> power floor notifications.
>
> power_floor_status : This attribute is present when a SoC supports
> power floor notification. When enabled this shows the current
> status of power floor.
>
> The power floor implementation provides interfaces, which are called
> from the sysfs callbacks to enable/disable and read power floor
> status. Also provides two additional interface to check if the current
> processor thermal device interrupt is for power floor status and
> send notification to user space.
>
> Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
> ---
>  .../driver-api/thermal/intel_dptf.rst         |   8 ++
>  .../thermal/intel/int340x_thermal/Makefile    |   1 +
>  .../processor_thermal_device.c                |  68 ++++++++++-
>  .../processor_thermal_device.h                |   8 ++
>  .../processor_thermal_power_floor.c           | 114 ++++++++++++++++++
>  5 files changed, 198 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c
>
> diff --git a/Documentation/driver-api/thermal/intel_dptf.rst b/Documentation/driver-api/thermal/intel_dptf.rst
> index 2d11e74ac665..55d90eafd94b 100644
> --- a/Documentation/driver-api/thermal/intel_dptf.rst
> +++ b/Documentation/driver-api/thermal/intel_dptf.rst
> @@ -164,6 +164,14 @@ ABI.
>  ``power_limit_1_tmax_us`` (RO)
>         Maximum powercap sysfs constraint_1_time_window_us for Intel RAPL
>
> +``power_floor_status`` (RO)
> +       When set to 1, hardware is not able to satisfy the requested power limit
> +       via Intel RAPL.
> +
> +``power_floor_enable`` (RW)
> +       When set to 1, enable reading and notification of power floor status.
> +       Notifications are issued for changes in the power_floor_status attribute.
> +
>  :file:`/sys/bus/pci/devices/0000\:00\:04.0/`
>
>  ``tcc_offset_degree_celsius`` (RW)
> diff --git a/drivers/thermal/intel/int340x_thermal/Makefile b/drivers/thermal/intel/int340x_thermal/Makefile
> index f33a3ad3bef3..fe3f43924525 100644
> --- a/drivers/thermal/intel/int340x_thermal/Makefile
> +++ b/drivers/thermal/intel/int340x_thermal/Makefile
> @@ -12,5 +12,6 @@ obj-$(CONFIG_INT340X_THERMAL) += processor_thermal_rfim.o
>  obj-$(CONFIG_INT340X_THERMAL)  += processor_thermal_mbox.o
>  obj-$(CONFIG_INT340X_THERMAL)  += processor_thermal_wt_req.o
>  obj-$(CONFIG_INT340X_THERMAL)  += processor_thermal_wt_hint.o
> +obj-$(CONFIG_INT340X_THERMAL)  += processor_thermal_power_floor.o
>  obj-$(CONFIG_INT3406_THERMAL)  += int3406_thermal.o
>  obj-$(CONFIG_ACPI_THERMAL_REL) += acpi_thermal_rel.o
> diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
> index 29ed7d0f7022..649f67fdf345 100644
> --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
> +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
> @@ -26,6 +26,48 @@ static ssize_t power_limit_##index##_##suffix##_show(struct device *dev, \
>         (unsigned long)proc_dev->power_limits[index].suffix * 1000); \
>  }
>
> +static ssize_t power_floor_status_show(struct device *dev,
> +                                      struct device_attribute *attr,
> +                                      char *buf)
> +{
> +       struct proc_thermal_device *proc_dev = dev_get_drvdata(dev);
> +       int ret;
> +
> +       ret = proc_thermal_read_power_floor_status(proc_dev);
> +
> +       return sysfs_emit(buf, "%d\n", ret);
> +}
> +
> +static ssize_t power_floor_enable_show(struct device *dev,
> +                                      struct device_attribute *attr,
> +                                      char *buf)
> +{
> +       struct proc_thermal_device *proc_dev = dev_get_drvdata(dev);
> +       bool ret;
> +
> +       ret = proc_thermal_power_floor_get_state(proc_dev);
> +
> +       return sysfs_emit(buf, "%d\n", ret);
> +}
> +
> +static ssize_t power_floor_enable_store(struct device *dev,
> +                                       struct device_attribute *attr,
> +                                       const char *buf, size_t count)
> +{
> +       struct proc_thermal_device *proc_dev = dev_get_drvdata(dev);
> +       u8 state;
> +       int ret;
> +
> +       if (kstrtou8(buf, 0, &state))
> +               return -EINVAL;
> +
> +       ret = proc_thermal_power_floor_set_state(proc_dev, !!state);
> +       if (ret)
> +               return ret;
> +
> +       return count;
> +}
> +
>  POWER_LIMIT_SHOW(0, min_uw)
>  POWER_LIMIT_SHOW(0, max_uw)
>  POWER_LIMIT_SHOW(0, step_uw)
> @@ -50,6 +92,9 @@ static DEVICE_ATTR_RO(power_limit_1_step_uw);
>  static DEVICE_ATTR_RO(power_limit_1_tmin_us);
>  static DEVICE_ATTR_RO(power_limit_1_tmax_us);
>
> +static DEVICE_ATTR_RO(power_floor_status);
> +static DEVICE_ATTR_RW(power_floor_enable);
> +
>  static struct attribute *power_limit_attrs[] = {
>         &dev_attr_power_limit_0_min_uw.attr,
>         &dev_attr_power_limit_1_min_uw.attr,
> @@ -61,12 +106,30 @@ static struct attribute *power_limit_attrs[] = {
>         &dev_attr_power_limit_1_tmin_us.attr,
>         &dev_attr_power_limit_0_tmax_us.attr,
>         &dev_attr_power_limit_1_tmax_us.attr,
> +       &dev_attr_power_floor_status.attr,
> +       &dev_attr_power_floor_enable.attr,
>         NULL
>  };
>
> +static umode_t power_limit_attr_visible(struct kobject *kobj, struct attribute *attr, int unused)
> +{
> +       struct device *dev = kobj_to_dev(kobj);
> +       struct proc_thermal_device *proc_dev;
> +
> +       if (attr != &dev_attr_power_floor_status.attr && attr != &dev_attr_power_floor_enable.attr)
> +               return attr->mode;
> +
> +       proc_dev = dev_get_drvdata(dev);
> +       if (!proc_dev || !(proc_dev->mmio_feature_mask & PROC_THERMAL_FEATURE_POWER_FLOOR))
> +               return 0;
> +
> +       return attr->mode;
> +}
> +
>  static const struct attribute_group power_limit_attribute_group = {
>         .attrs = power_limit_attrs,
> -       .name = "power_limits"
> +       .name = "power_limits",
> +       .is_visible = power_limit_attr_visible,
>  };
>
>  static ssize_t tcc_offset_degree_celsius_show(struct device *dev,
> @@ -380,6 +443,9 @@ void proc_thermal_mmio_remove(struct pci_dev *pdev, struct proc_thermal_device *
>             proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_DVFS)
>                 proc_thermal_rfim_remove(pdev);
>
> +       if (proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_POWER_FLOOR)
> +               proc_thermal_power_floor_set_state(proc_priv, false);
> +
>         if (proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_WT_REQ)
>                 proc_thermal_wt_req_remove(pdev);
>         else if (proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_WT_HINT)
> diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
> index dd025c8c2bac..89e98f025a49 100644
> --- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
> +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
> @@ -63,6 +63,7 @@ struct rapl_mmio_regs {
>  #define PROC_THERMAL_FEATURE_WT_REQ    0x08
>  #define PROC_THERMAL_FEATURE_DLVR      0x10
>  #define PROC_THERMAL_FEATURE_WT_HINT   0x20
> +#define PROC_THERMAL_FEATURE_POWER_FLOOR       0x40
>
>  #if IS_ENABLED(CONFIG_PROC_THERMAL_MMIO_RAPL)
>  int proc_thermal_rapl_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv);
> @@ -91,6 +92,13 @@ void proc_thermal_wt_req_remove(struct pci_dev *pdev);
>  #define MBOX_DATA_BIT_AC_DC            30
>  #define MBOX_DATA_BIT_VALID            31
>
> +int proc_thermal_read_power_floor_status(struct proc_thermal_device *proc_priv);
> +int proc_thermal_power_floor_set_state(struct proc_thermal_device *proc_priv, bool enable);
> +bool proc_thermal_power_floor_get_state(struct proc_thermal_device *proc_priv);
> +void proc_thermal_power_floor_intr_callback(struct pci_dev *pdev,
> +                                           struct proc_thermal_device *proc_priv);
> +bool proc_thermal_check_power_floor_intr(struct proc_thermal_device *proc_priv);
> +
>  int processor_thermal_send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp);
>  int processor_thermal_send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data);
>  int processor_thermal_mbox_interrupt_config(struct pci_dev *pdev, bool enable, int enable_bit,
> diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c
> new file mode 100644
> index 000000000000..cac3a38f430f
> --- /dev/null
> +++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c
> @@ -0,0 +1,114 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Processor thermal device module for registering and processing
> + * power floor. When the hardware reduces the power to the minimum
> + * possible, the power floor is notified via an interrupt.
> + *
> + * Operation:
> + * When user space enables power floor reporting:
> + * - Use mailbox to:
> + *     Enable processor thermal device interrupt
> + *
> + * - Current status of power floor is read from offset 0x5B18
> + *   bit 39.
> + *
> + * Two interface functions are provided to call when there is a
> + * thermal device interrupt:
> + * - proc_thermal_power_floor_intr():
> + *     Check if the interrupt is for change in power floor.
> + *     Called from interrupt context.
> + *
> + * - proc_thermal_power_floor_intr_callback():
> + *     Callback for interrupt processing in thread context. This involves
> + *     sending notification to user space that there is a change in the
> + *     power floor status.
> + *
> + * Copyright (c) 2023, Intel Corporation.
> + */
> +
> +#include <linux/pci.h>
> +#include "processor_thermal_device.h"
> +
> +#define SOC_POWER_FLOOR_INT_STATUS_OFF 0x5B18

"OFFSET" would be better than "OFF" IMO.

> +#define SOC_POWER_FLOOR_STATUS         BIT(39)
> +#define SOC_POWER_FLOOR_SHIFT          39
> +
> +#define SOC_POWER_FLOOR_INT_ENABLE_BIT 31
> +#define SOC_POWER_FLOOR_INT_ACTIVE     BIT(3)
> +
> +/* Mark time windows as invalid as this is not applicable */

The meaning of the above comment is unclear.

> +#define SOC_POWER_FLOOR_TIME_WINDOW    -1
> +
> +int proc_thermal_read_power_floor_status(struct proc_thermal_device *proc_priv)
> +{
> +       u64 status = 0;
> +
> +       status = readq(proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
> +       return (status & SOC_POWER_FLOOR_STATUS) >> SOC_POWER_FLOOR_SHIFT;
> +}
> +EXPORT_SYMBOL_NS_GPL(proc_thermal_read_power_floor_status, INT340X_THERMAL);
> +
> +static bool enable_state;
> +static DEFINE_MUTEX(pf_lock);
> +
> +int proc_thermal_power_floor_set_state(struct proc_thermal_device *proc_priv, bool enable)
> +{
> +       int ret = 0;
> +
> +       mutex_lock(&pf_lock);
> +       if (enable_state == enable)
> +               goto pf_unlock;
> +
> +       ret = processor_thermal_mbox_interrupt_config(to_pci_dev(proc_priv->dev), enable,
> +                                                     SOC_POWER_FLOOR_INT_ENABLE_BIT,
> +                                                     SOC_POWER_FLOOR_TIME_WINDOW);
> +       if (!ret)
> +               enable_state = enable;
> +
> +pf_unlock:
> +       mutex_unlock(&pf_lock);
> +
> +       return ret;
> +}
> +EXPORT_SYMBOL_NS_GPL(proc_thermal_power_floor_set_state, INT340X_THERMAL);
> +
> +bool proc_thermal_power_floor_get_state(struct proc_thermal_device *proc_priv)
> +{
> +       return enable_state;
> +}
> +EXPORT_SYMBOL_NS_GPL(proc_thermal_power_floor_get_state, INT340X_THERMAL);
> +
> +/*
> + * Callback to check if interrupt for power floor is active.
> + * Caution: Called from interrupt context.
> + */

I would prefer this comment and the one below to be proper kerneldoc
ones or to be moved inside the functions.

> +bool proc_thermal_check_power_floor_intr(struct proc_thermal_device *proc_priv)
> +{
> +       u64 int_status;
> +
> +       int_status = readq(proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
> +       if (int_status & SOC_POWER_FLOOR_INT_ACTIVE)
> +               return true;
> +
> +       return false;

return !!(int_status & SOC_POWER_FLOOR_INT_ACTIVE);

> +}
> +EXPORT_SYMBOL_NS_GPL(proc_thermal_check_power_floor_intr, INT340X_THERMAL);
> +
> +/* Callback to notify user space */

Notify user space about what and how?  As is, this comment isn't very
useful IMO.

> +void proc_thermal_power_floor_intr_callback(struct pci_dev *pdev,
> +                                           struct proc_thermal_device *proc_priv)
> +{
> +       u64 status;
> +
> +       status = readq(proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
> +       if (!(status & SOC_POWER_FLOOR_INT_ACTIVE))
> +               return;
> +
> +       writeq(status & ~SOC_POWER_FLOOR_INT_ACTIVE,
> +              proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
> +       sysfs_notify(&pdev->dev.kobj, "power_limits", "power_floor_status");
> +}
> +EXPORT_SYMBOL_NS_GPL(proc_thermal_power_floor_intr_callback, INT340X_THERMAL);
> +
> +MODULE_IMPORT_NS(INT340X_THERMAL);
> +MODULE_LICENSE("GPL");
> --
diff mbox series

Patch

diff --git a/Documentation/driver-api/thermal/intel_dptf.rst b/Documentation/driver-api/thermal/intel_dptf.rst
index 2d11e74ac665..55d90eafd94b 100644
--- a/Documentation/driver-api/thermal/intel_dptf.rst
+++ b/Documentation/driver-api/thermal/intel_dptf.rst
@@ -164,6 +164,14 @@  ABI.
 ``power_limit_1_tmax_us`` (RO)
 	Maximum powercap sysfs constraint_1_time_window_us for Intel RAPL
 
+``power_floor_status`` (RO)
+	When set to 1, hardware is not able to satisfy the requested power limit
+	via Intel RAPL.
+
+``power_floor_enable`` (RW)
+	When set to 1, enable reading and notification of power floor status.
+	Notifications are issued for changes in the power_floor_status attribute.
+
 :file:`/sys/bus/pci/devices/0000\:00\:04.0/`
 
 ``tcc_offset_degree_celsius`` (RW)
diff --git a/drivers/thermal/intel/int340x_thermal/Makefile b/drivers/thermal/intel/int340x_thermal/Makefile
index f33a3ad3bef3..fe3f43924525 100644
--- a/drivers/thermal/intel/int340x_thermal/Makefile
+++ b/drivers/thermal/intel/int340x_thermal/Makefile
@@ -12,5 +12,6 @@  obj-$(CONFIG_INT340X_THERMAL)	+= processor_thermal_rfim.o
 obj-$(CONFIG_INT340X_THERMAL)	+= processor_thermal_mbox.o
 obj-$(CONFIG_INT340X_THERMAL)	+= processor_thermal_wt_req.o
 obj-$(CONFIG_INT340X_THERMAL)	+= processor_thermal_wt_hint.o
+obj-$(CONFIG_INT340X_THERMAL)	+= processor_thermal_power_floor.o
 obj-$(CONFIG_INT3406_THERMAL)	+= int3406_thermal.o
 obj-$(CONFIG_ACPI_THERMAL_REL)	+= acpi_thermal_rel.o
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
index 29ed7d0f7022..649f67fdf345 100644
--- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
+++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.c
@@ -26,6 +26,48 @@  static ssize_t power_limit_##index##_##suffix##_show(struct device *dev, \
 	(unsigned long)proc_dev->power_limits[index].suffix * 1000); \
 }
 
+static ssize_t power_floor_status_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	struct proc_thermal_device *proc_dev = dev_get_drvdata(dev);
+	int ret;
+
+	ret = proc_thermal_read_power_floor_status(proc_dev);
+
+	return sysfs_emit(buf, "%d\n", ret);
+}
+
+static ssize_t power_floor_enable_show(struct device *dev,
+				       struct device_attribute *attr,
+				       char *buf)
+{
+	struct proc_thermal_device *proc_dev = dev_get_drvdata(dev);
+	bool ret;
+
+	ret = proc_thermal_power_floor_get_state(proc_dev);
+
+	return sysfs_emit(buf, "%d\n", ret);
+}
+
+static ssize_t power_floor_enable_store(struct device *dev,
+					struct device_attribute *attr,
+					const char *buf, size_t count)
+{
+	struct proc_thermal_device *proc_dev = dev_get_drvdata(dev);
+	u8 state;
+	int ret;
+
+	if (kstrtou8(buf, 0, &state))
+		return -EINVAL;
+
+	ret = proc_thermal_power_floor_set_state(proc_dev, !!state);
+	if (ret)
+		return ret;
+
+	return count;
+}
+
 POWER_LIMIT_SHOW(0, min_uw)
 POWER_LIMIT_SHOW(0, max_uw)
 POWER_LIMIT_SHOW(0, step_uw)
@@ -50,6 +92,9 @@  static DEVICE_ATTR_RO(power_limit_1_step_uw);
 static DEVICE_ATTR_RO(power_limit_1_tmin_us);
 static DEVICE_ATTR_RO(power_limit_1_tmax_us);
 
+static DEVICE_ATTR_RO(power_floor_status);
+static DEVICE_ATTR_RW(power_floor_enable);
+
 static struct attribute *power_limit_attrs[] = {
 	&dev_attr_power_limit_0_min_uw.attr,
 	&dev_attr_power_limit_1_min_uw.attr,
@@ -61,12 +106,30 @@  static struct attribute *power_limit_attrs[] = {
 	&dev_attr_power_limit_1_tmin_us.attr,
 	&dev_attr_power_limit_0_tmax_us.attr,
 	&dev_attr_power_limit_1_tmax_us.attr,
+	&dev_attr_power_floor_status.attr,
+	&dev_attr_power_floor_enable.attr,
 	NULL
 };
 
+static umode_t power_limit_attr_visible(struct kobject *kobj, struct attribute *attr, int unused)
+{
+	struct device *dev = kobj_to_dev(kobj);
+	struct proc_thermal_device *proc_dev;
+
+	if (attr != &dev_attr_power_floor_status.attr && attr != &dev_attr_power_floor_enable.attr)
+		return attr->mode;
+
+	proc_dev = dev_get_drvdata(dev);
+	if (!proc_dev || !(proc_dev->mmio_feature_mask & PROC_THERMAL_FEATURE_POWER_FLOOR))
+		return 0;
+
+	return attr->mode;
+}
+
 static const struct attribute_group power_limit_attribute_group = {
 	.attrs = power_limit_attrs,
-	.name = "power_limits"
+	.name = "power_limits",
+	.is_visible = power_limit_attr_visible,
 };
 
 static ssize_t tcc_offset_degree_celsius_show(struct device *dev,
@@ -380,6 +443,9 @@  void proc_thermal_mmio_remove(struct pci_dev *pdev, struct proc_thermal_device *
 	    proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_DVFS)
 		proc_thermal_rfim_remove(pdev);
 
+	if (proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_POWER_FLOOR)
+		proc_thermal_power_floor_set_state(proc_priv, false);
+
 	if (proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_WT_REQ)
 		proc_thermal_wt_req_remove(pdev);
 	else if (proc_priv->mmio_feature_mask & PROC_THERMAL_FEATURE_WT_HINT)
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
index dd025c8c2bac..89e98f025a49 100644
--- a/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
+++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_device.h
@@ -63,6 +63,7 @@  struct rapl_mmio_regs {
 #define PROC_THERMAL_FEATURE_WT_REQ	0x08
 #define PROC_THERMAL_FEATURE_DLVR	0x10
 #define PROC_THERMAL_FEATURE_WT_HINT	0x20
+#define PROC_THERMAL_FEATURE_POWER_FLOOR	0x40
 
 #if IS_ENABLED(CONFIG_PROC_THERMAL_MMIO_RAPL)
 int proc_thermal_rapl_add(struct pci_dev *pdev, struct proc_thermal_device *proc_priv);
@@ -91,6 +92,13 @@  void proc_thermal_wt_req_remove(struct pci_dev *pdev);
 #define MBOX_DATA_BIT_AC_DC		30
 #define MBOX_DATA_BIT_VALID		31
 
+int proc_thermal_read_power_floor_status(struct proc_thermal_device *proc_priv);
+int proc_thermal_power_floor_set_state(struct proc_thermal_device *proc_priv, bool enable);
+bool proc_thermal_power_floor_get_state(struct proc_thermal_device *proc_priv);
+void proc_thermal_power_floor_intr_callback(struct pci_dev *pdev,
+					    struct proc_thermal_device *proc_priv);
+bool proc_thermal_check_power_floor_intr(struct proc_thermal_device *proc_priv);
+
 int processor_thermal_send_mbox_read_cmd(struct pci_dev *pdev, u16 id, u64 *resp);
 int processor_thermal_send_mbox_write_cmd(struct pci_dev *pdev, u16 id, u32 data);
 int processor_thermal_mbox_interrupt_config(struct pci_dev *pdev, bool enable, int enable_bit,
diff --git a/drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c b/drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c
new file mode 100644
index 000000000000..cac3a38f430f
--- /dev/null
+++ b/drivers/thermal/intel/int340x_thermal/processor_thermal_power_floor.c
@@ -0,0 +1,114 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Processor thermal device module for registering and processing
+ * power floor. When the hardware reduces the power to the minimum
+ * possible, the power floor is notified via an interrupt.
+ *
+ * Operation:
+ * When user space enables power floor reporting:
+ * - Use mailbox to:
+ *	Enable processor thermal device interrupt
+ *
+ * - Current status of power floor is read from offset 0x5B18
+ *   bit 39.
+ *
+ * Two interface functions are provided to call when there is a
+ * thermal device interrupt:
+ * - proc_thermal_power_floor_intr():
+ *	Check if the interrupt is for change in power floor.
+ *	Called from interrupt context.
+ *
+ * - proc_thermal_power_floor_intr_callback():
+ *	Callback for interrupt processing in thread context. This involves
+ *	sending notification to user space that there is a change in the
+ *	power floor status.
+ *
+ * Copyright (c) 2023, Intel Corporation.
+ */
+
+#include <linux/pci.h>
+#include "processor_thermal_device.h"
+
+#define SOC_POWER_FLOOR_INT_STATUS_OFF	0x5B18
+#define SOC_POWER_FLOOR_STATUS		BIT(39)
+#define SOC_POWER_FLOOR_SHIFT		39
+
+#define SOC_POWER_FLOOR_INT_ENABLE_BIT	31
+#define SOC_POWER_FLOOR_INT_ACTIVE	BIT(3)
+
+/* Mark time windows as invalid as this is not applicable */
+#define SOC_POWER_FLOOR_TIME_WINDOW	-1
+
+int proc_thermal_read_power_floor_status(struct proc_thermal_device *proc_priv)
+{
+	u64 status = 0;
+
+	status = readq(proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
+	return (status & SOC_POWER_FLOOR_STATUS) >> SOC_POWER_FLOOR_SHIFT;
+}
+EXPORT_SYMBOL_NS_GPL(proc_thermal_read_power_floor_status, INT340X_THERMAL);
+
+static bool enable_state;
+static DEFINE_MUTEX(pf_lock);
+
+int proc_thermal_power_floor_set_state(struct proc_thermal_device *proc_priv, bool enable)
+{
+	int ret = 0;
+
+	mutex_lock(&pf_lock);
+	if (enable_state == enable)
+		goto pf_unlock;
+
+	ret = processor_thermal_mbox_interrupt_config(to_pci_dev(proc_priv->dev), enable,
+						      SOC_POWER_FLOOR_INT_ENABLE_BIT,
+						      SOC_POWER_FLOOR_TIME_WINDOW);
+	if (!ret)
+		enable_state = enable;
+
+pf_unlock:
+	mutex_unlock(&pf_lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_NS_GPL(proc_thermal_power_floor_set_state, INT340X_THERMAL);
+
+bool proc_thermal_power_floor_get_state(struct proc_thermal_device *proc_priv)
+{
+	return enable_state;
+}
+EXPORT_SYMBOL_NS_GPL(proc_thermal_power_floor_get_state, INT340X_THERMAL);
+
+/*
+ * Callback to check if interrupt for power floor is active.
+ * Caution: Called from interrupt context.
+ */
+bool proc_thermal_check_power_floor_intr(struct proc_thermal_device *proc_priv)
+{
+	u64 int_status;
+
+	int_status = readq(proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
+	if (int_status & SOC_POWER_FLOOR_INT_ACTIVE)
+		return true;
+
+	return false;
+}
+EXPORT_SYMBOL_NS_GPL(proc_thermal_check_power_floor_intr, INT340X_THERMAL);
+
+/* Callback to notify user space */
+void proc_thermal_power_floor_intr_callback(struct pci_dev *pdev,
+					    struct proc_thermal_device *proc_priv)
+{
+	u64 status;
+
+	status = readq(proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
+	if (!(status & SOC_POWER_FLOOR_INT_ACTIVE))
+		return;
+
+	writeq(status & ~SOC_POWER_FLOOR_INT_ACTIVE,
+	       proc_priv->mmio_base + SOC_POWER_FLOOR_INT_STATUS_OFF);
+	sysfs_notify(&pdev->dev.kobj, "power_limits", "power_floor_status");
+}
+EXPORT_SYMBOL_NS_GPL(proc_thermal_power_floor_intr_callback, INT340X_THERMAL);
+
+MODULE_IMPORT_NS(INT340X_THERMAL);
+MODULE_LICENSE("GPL");