diff mbox series

[RESEND,v2,3/3] power: supply: Introduce MM8013 fuel gauge driver

Message ID 20230621-topic-mm8013-v2-3-9f1b41f4bc06@linaro.org
State New
Headers show
Series [RESEND,v2,1/3] dt-bindings: vendor-prefixes: Add Mitsumi Electric Co., Ltd. | expand

Commit Message

Konrad Dybcio Aug. 23, 2023, 2:36 p.m. UTC 
Add a driver for the Mitsumi MM8013 fuel gauge. The driver is a vastly
cleaned up and improved version of the one that shipped in some obscure
Lenovo downstream kernel [1], with some register definitions borrowed from
ChromeOS EC platform code [2].

[1] https://github.com/adazem009/kernel_lenovo_bengal/commit/b6b346427a871715709bd22aae449b9383f3b66b
[2] https://chromium.googlesource.com/chromiumos/platform/ec/+/master/driver/battery/mm8013.h
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 MAINTAINERS                   |   5 +
 drivers/power/supply/Kconfig  |   9 ++
 drivers/power/supply/Makefile |   1 +
 drivers/power/supply/mm8013.c | 283 ++++++++++++++++++++++++++++++++++++++++++
 4 files changed, 298 insertions(+)

Comments

Konrad Dybcio Sept. 14, 2023, 6:46 p.m. UTC | #1 
On 13.09.2023 17:45, Sebastian Reichel wrote:
> Hi,
> 
> On Wed, Aug 23, 2023 at 04:36:15PM +0200, Konrad Dybcio wrote:
>> Add a driver for the Mitsumi MM8013 fuel gauge. The driver is a vastly
>> cleaned up and improved version of the one that shipped in some obscure
>> Lenovo downstream kernel [1], with some register definitions borrowed from
>> ChromeOS EC platform code [2].
>>
>> [1] https://github.com/adazem009/kernel_lenovo_bengal/commit/b6b346427a871715709bd22aae449b9383f3b66b
>> [2] https://chromium.googlesource.com/chromiumos/platform/ec/+/master/driver/battery/mm8013.h
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
[...]

> 
> Please use regmap.
Ack

[...]

>> +	switch (psp) {
>> +	case POWER_SUPPLY_PROP_CAPACITY:
> 
> this is in %, while the next two are in uAh. So the fuel gauge does
> not provide the current capacity in uAh
> (POWER_SUPPLY_PROP_CHARGE_NOW)?
Yes. Doesn't seem like raw values are supported.

[...]

> 
> this is just 'val->intval = (s16) ret;'.
> 
>> +		val->intval *= -1000;
Ack

> 
> and this seems to be the only property, that properly scales its
> values, assuming the hardware reports data in mA.
> 

[...]

> 
> that's in **micro** volts
Oh, I didn't read enough docs..

> 
>> +		ret = mm8013_read_reg(client, REG_VOLTAGE);
> 
> this effectively does i2c_smbus_read_word_data() and thus the
> maximum is is 65536. 65536uV = 65mV. I have serious doubts, that
> this code does what you want. The same is true for a couple of
> the other properties.
Ack

[...]

> With the next submission please include a dump of the uevent
> in sysfs in the cover letter or below the fold, so that its
> easy to validty check if the reported values look sensible.
State of what-will-be-sent in v(n+1), with additional fixups:

POWER_SUPPLY_NAME=mm8013
POWER_SUPPLY_TYPE=Battery
POWER_SUPPLY_CAPACITY=100
POWER_SUPPLY_CHARGE_FULL=7124
POWER_SUPPLY_CHARGE_FULL_DESIGN=7500
POWER_SUPPLY_CURRENT_NOW=-122000
POWER_SUPPLY_CYCLE_COUNT=27
POWER_SUPPLY_HEALTH=Good
POWER_SUPPLY_PRESENT=1
POWER_SUPPLY_STATUS=Full
POWER_SUPPLY_TEMP=324
POWER_SUPPLY_VOLTAGE_NOW=4407000


> 
> Thanks and sorry for the slow processing,
No worries

Konrad
Sebastian Reichel Sept. 14, 2023, 7:17 p.m. UTC | #2 
Hi,

On Thu, Sep 14, 2023 at 08:46:21PM +0200, Konrad Dybcio wrote:
> On 13.09.2023 17:45, Sebastian Reichel wrote:
> > On Wed, Aug 23, 2023 at 04:36:15PM +0200, Konrad Dybcio wrote:
> >> Add a driver for the Mitsumi MM8013 fuel gauge. The driver is a vastly
> >> cleaned up and improved version of the one that shipped in some obscure
> >> Lenovo downstream kernel [1], with some register definitions borrowed from
> >> ChromeOS EC platform code [2].
> >>
> >> [1] https://github.com/adazem009/kernel_lenovo_bengal/commit/b6b346427a871715709bd22aae449b9383f3b66b
> >> [2] https://chromium.googlesource.com/chromiumos/platform/ec/+/master/driver/battery/mm8013.h
> >> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> >> ---
> [...]

[...]

> >> +	switch (psp) {
> >> +	case POWER_SUPPLY_PROP_CAPACITY:
> > 
> > this is in %, while the next two are in uAh. So the fuel gauge does
> > not provide the current capacity in uAh
> > (POWER_SUPPLY_PROP_CHARGE_NOW)?
> Yes. Doesn't seem like raw values are supported.

Ok. (It's quite unusual for a chip to provide design and full
capacity separatly, but not providing the current capacity.)

[...]

> > With the next submission please include a dump of the uevent
> > in sysfs in the cover letter or below the fold, so that its
> > easy to validty check if the reported values look sensible.
> State of what-will-be-sent in v(n+1), with additional fixups:
> 
> POWER_SUPPLY_NAME=mm8013
> POWER_SUPPLY_TYPE=Battery
> POWER_SUPPLY_CAPACITY=100
> POWER_SUPPLY_CHARGE_FULL=7124
> POWER_SUPPLY_CHARGE_FULL_DESIGN=7500

The unit for the above two are uAh. So that would be 7.5 mAh. With
4.4V I expect you have something bigger than a coin cell, so that's
probably wrong :)

> POWER_SUPPLY_CURRENT_NOW=-122000
> POWER_SUPPLY_CYCLE_COUNT=27
> POWER_SUPPLY_HEALTH=Good
> POWER_SUPPLY_PRESENT=1
> POWER_SUPPLY_STATUS=Full
> POWER_SUPPLY_TEMP=324
> POWER_SUPPLY_VOLTAGE_NOW=4407000

Otherwise looks sensible.

Greetings,

-- Sebastian
diff mbox series

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index 5ce188b58eaa..ba5f075a2ca8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -14296,6 +14296,11 @@  W:	https://linuxtv.org
 T:	git git://linuxtv.org/media_tree.git
 F:	drivers/media/radio/radio-miropcm20*
 
+MITSUMI MM8013 FG DRIVER
+M:	Konrad Dybcio <konradybcio@kernel.org>
+F:	Documentation/devicetree/bindings/power/supply/mitsumi,mm8013.yaml
+F:	drivers/power/supply/mm8013.c
+
 MMP SUPPORT
 R:	Lubomir Rintel <lkundrak@v3.sk>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 663a1c423806..c19e8287d80f 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -951,4 +951,13 @@  config CHARGER_QCOM_SMB2
 	  adds support for the SMB2 switch mode battery charger found
 	  in PMI8998 and related PMICs.
 
+config FUEL_GAUGE_MM8013
+	tristate "Mitsumi MM8013 fuel gauge driver"
+	depends on I2C
+	help
+	  Say Y here to enable the Mitsumi MM8013 fuel gauge driver.
+	  It enables the monitoring of many battery parameters, including
+	  the state of charge, temperature, cycle count, actual and design
+	  capacity, etc.
+
 endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index a8a9fa6de1e9..ba2c41f060be 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -111,3 +111,4 @@  obj-$(CONFIG_BATTERY_SURFACE)	+= surface_battery.o
 obj-$(CONFIG_CHARGER_SURFACE)	+= surface_charger.o
 obj-$(CONFIG_BATTERY_UG3105)	+= ug3105_battery.o
 obj-$(CONFIG_CHARGER_QCOM_SMB2)	+= qcom_pmi8998_charger.o
+obj-$(CONFIG_FUEL_GAUGE_MM8013)	+= mm8013.o
diff --git a/drivers/power/supply/mm8013.c b/drivers/power/supply/mm8013.c
new file mode 100644
index 000000000000..ce20c6078116
--- /dev/null
+++ b/drivers/power/supply/mm8013.c
@@ -0,0 +1,283 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2016-2019 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2023, Linaro Limited
+ */
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/power_supply.h>
+
+#define REG_BATID			0x00 /* This one is very unclear */
+ #define BATID_101			0x0101 /* 107kOhm */
+ #define BATID_102			0x0102 /* 10kOhm */
+#define REG_TEMPERATURE			0x06
+#define REG_VOLTAGE			0x08
+#define REG_FLAGS			0x0a
+ #define MM8013_FLAG_OTC		BIT(15)
+ #define MM8013_FLAG_OTD		BIT(14)
+ #define MM8013_FLAG_BATHI		BIT(13)
+ #define MM8013_FLAG_FC			BIT(9)
+ #define MM8013_FLAG_CHG		BIT(8)
+ #define MM8013_FLAG_DSG		BIT(0)
+#define REG_FULL_CHARGE_CAPACITY	0x0e
+#define REG_AVERAGE_CURRENT		0x14
+#define REG_AVERAGE_TIME_TO_EMPTY	0x16
+#define REG_AVERAGE_TIME_TO_FULL	0x18
+#define REG_CYCLE_COUNT			0x2a
+#define REG_STATE_OF_CHARGE		0x2c
+#define REG_DESIGN_CAPACITY		0x3c
+/* TODO: 0x62-0x68 seem to contain 'MM8013C' in a length-prefixed, non-terminated string */
+
+#define DECIKELVIN_TO_DECIDEGC(t)	(t - 2731)
+
+struct mm8013_chip {
+	struct i2c_client *client;
+};
+
+static int mm8013_write_reg(struct i2c_client *client, u8 reg, u16 value)
+{
+	int ret;
+
+	ret = i2c_smbus_write_word_data(client, reg, value);
+	if (ret < 0)
+		dev_err(&client->dev, "%s: err %d\n", __func__, ret);
+
+	usleep_range(4000, 5000);
+	return ret;
+}
+
+static int mm8013_read_reg(struct i2c_client *client, u8 reg)
+{
+	int ret;
+
+	ret = i2c_smbus_read_word_data(client, reg);
+	if (ret < 0)
+		dev_err(&client->dev, "%s: err %d\n", __func__, ret);
+
+	usleep_range(4000, 5000);
+	return ret;
+}
+
+static int mm8013_checkdevice(struct mm8013_chip *chip)
+{
+	int battery_id, ret;
+
+	ret = mm8013_write_reg(chip->client, REG_BATID, 0x0008);
+	if (ret < 0)
+		return ret;
+
+	ret = mm8013_read_reg(chip->client, REG_BATID);
+	if (ret < 0)
+		return ret;
+
+	if (ret == BATID_102)
+		battery_id = 2;
+	else if (ret == BATID_101)
+		battery_id = 1;
+	else
+		return -EINVAL;
+
+	dev_dbg(&chip->client->dev, "battery_id: %d\n", battery_id);
+
+	return 0;
+}
+
+static enum power_supply_property mm8013_battery_props[] = {
+	POWER_SUPPLY_PROP_CAPACITY,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CYCLE_COUNT,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG,
+	POWER_SUPPLY_PROP_TIME_TO_FULL_AVG,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+};
+
+static int mm8013_get_property(struct power_supply *psy,
+			       enum power_supply_property psp,
+			       union power_supply_propval *val)
+{
+	struct mm8013_chip *chip = psy->drv_data;
+	struct i2c_client *client = chip->client;
+	int ret = 0;
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_CAPACITY:
+		ret = mm8013_read_reg(client, REG_STATE_OF_CHARGE);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL:
+		ret = mm8013_read_reg(client, REG_FULL_CHARGE_CAPACITY);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
+		ret = mm8013_read_reg(client, REG_DESIGN_CAPACITY);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret;
+		break;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		ret = mm8013_read_reg(client, REG_AVERAGE_CURRENT);
+		if (ret < 0)
+			return ret;
+
+		if (ret > S16_MAX)
+			val->intval -= (1 << 16);
+		else
+			val->intval = ret;
+
+		val->intval *= -1000;
+		break;
+	case POWER_SUPPLY_PROP_CYCLE_COUNT:
+		ret = mm8013_read_reg(client, REG_CYCLE_COUNT);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret;
+		break;
+	case POWER_SUPPLY_PROP_HEALTH:
+		ret = mm8013_read_reg(client, REG_FLAGS);
+		if (ret < 0)
+			return ret;
+
+		if (ret & MM8013_FLAG_BATHI)
+			val->intval = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+		else if (ret & (MM8013_FLAG_OTD | MM8013_FLAG_OTC))
+			val->intval = POWER_SUPPLY_HEALTH_OVERHEAT;
+		else
+			val->intval = POWER_SUPPLY_HEALTH_GOOD;
+		break;
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = mm8013_read_reg(client, REG_TEMPERATURE) > 0;
+		break;
+	case POWER_SUPPLY_PROP_STATUS:
+		ret = mm8013_read_reg(client, REG_FLAGS);
+		if (ret < 0)
+			return ret;
+
+		if (ret & MM8013_FLAG_DSG)
+			val->intval = POWER_SUPPLY_STATUS_DISCHARGING;
+		else if (ret & MM8013_FLAG_CHG)
+			val->intval = POWER_SUPPLY_STATUS_CHARGING;
+		else if (ret & MM8013_FLAG_FC)
+			val->intval = POWER_SUPPLY_STATUS_FULL;
+		else
+			val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+		break;
+	case POWER_SUPPLY_PROP_TEMP:
+		ret = mm8013_read_reg(client, REG_TEMPERATURE);
+		if (ret < 0)
+			return ret;
+
+		val->intval = DECIKELVIN_TO_DECIDEGC(ret);
+		break;
+	case POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG:
+		ret = mm8013_read_reg(client, REG_AVERAGE_TIME_TO_EMPTY);
+		if (ret < 0)
+			return ret;
+
+		/* The estimation is not yet ready */
+		if (ret == U16_MAX)
+			return -ENODATA;
+
+		val->intval = ret;
+		break;
+	case POWER_SUPPLY_PROP_TIME_TO_FULL_AVG:
+		ret = mm8013_read_reg(client, REG_AVERAGE_TIME_TO_FULL);
+		if (ret < 0)
+			return ret;
+
+		/* The estimation is not yet ready */
+		if (ret == U16_MAX)
+			return -ENODATA;
+
+		val->intval = ret;
+		break;
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		ret = mm8013_read_reg(client, REG_VOLTAGE);
+		if (ret < 0)
+			return ret;
+
+		val->intval = ret;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct power_supply_desc mm8013_desc = {
+	.name			= "mm8013",
+	.type			= POWER_SUPPLY_TYPE_BATTERY,
+	.properties		= mm8013_battery_props,
+	.num_properties		= ARRAY_SIZE(mm8013_battery_props),
+	.get_property		= mm8013_get_property,
+};
+
+static int mm8013_probe(struct i2c_client *client)
+{
+	struct power_supply_config psy_cfg = {};
+	struct device *dev = &client->dev;
+	struct power_supply *psy;
+	struct mm8013_chip *chip;
+	int ret = 0;
+
+	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_WORD_DATA))
+		return dev_err_probe(dev, -EIO,
+				     "I2C_FUNC_SMBUS_WORD_DATA not supported\n");
+
+	chip = devm_kzalloc(dev, sizeof(struct mm8013_chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->client = client;
+
+	ret = mm8013_checkdevice(chip);
+	if (ret)
+		return dev_err_probe(dev, -ENODEV, "MM8013 not found\n");
+
+	psy_cfg.drv_data = chip;
+	psy_cfg.of_node = dev->of_node;
+
+	psy = devm_power_supply_register(dev, &mm8013_desc, &psy_cfg);
+	if (IS_ERR(psy))
+		return PTR_ERR(psy);
+
+	return 0;
+}
+
+static const struct i2c_device_id mm8013_id_table[] = {
+	{ "mm8013", 0 },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, mm8013_id_table);
+
+static const struct of_device_id mm8013_match_table[] = {
+	{ .compatible = "mitsumi,mm8013" },
+	{ },
+};
+
+static struct i2c_driver mm8013_i2c_driver = {
+	.probe = mm8013_probe,
+	.id_table = mm8013_id_table,
+	.driver = {
+		.name = "mm8013",
+		.of_match_table = mm8013_match_table,
+	},
+};
+module_i2c_driver(mm8013_i2c_driver);
+
+MODULE_DESCRIPTION("MM8013 fuel gauge driver");
+MODULE_LICENSE("GPL");