| Message ID | 20230823091757.31311-3-quic_nitirawa@quicinc.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | None | expand |
On 8/23/2023 2:47 PM, Nitin Rawat wrote: > Add SC7280 specific register layout and table configs. > > Co-developed-by: Manish Pandey <quic_mapa@quicinc.com> > Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> > Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++ > 1 file changed, 142 insertions(+) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > index 3927eba8e468..514fa14df634 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > @@ -177,6 +177,111 @@ static const struct qmp_phy_init_tbl msm8996_ufsphy_rx[] = { > QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0E), > }; > > +static const struct qmp_phy_init_tbl sc7280_ufsphy_tx[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1, 0x06), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1, 0x03), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_3_DIVIDER_BAND0_1, 0x01), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_4_DIVIDER_BAND0_1, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x35), > + QMP_PHY_INIT_CFG(QSERDES_V4_TX_TRAN_DRVR_EMP_EN, 0x0c), > +}; > + > +static const struct qmp_phy_init_tbl sc7280_ufsphy_rx[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x80), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0e), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x1b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1d), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x10), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x6d), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x6d), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xed), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x3b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x3c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xe0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xc8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xc8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb1), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c), > +}; > + > +static const struct qmp_phy_init_tbl sc7280_ufsphy_pcs[] = { > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_SIGDET_CTRL2, 0x6d), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0a), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_SMALL_AMP_DRV_LVL, 0x02), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_MID_TERM_CTRL1, 0x43), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_DEBUG_BUS_CLKSEL, 0x1f), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_MULTI_LANE_CTRL1, 0x02), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_PLL_CNTL, 0x03), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB, 0x16), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB, 0xd8), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_PWM_GEAR_BAND, 0xaa), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_HS_GEAR_BAND, 0x06), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x03), > + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x03), > +}; > + > +static const struct qmp_phy_init_tbl sc7280_ufsphy_hs_g4_rx[] = { > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x81), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0e), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x6f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL1, 0x04), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x09), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x07), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x17), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x20), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0x80), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x01), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x3f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xff), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x2c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0x6d), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0x6d), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xed), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x3c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c), > + QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x0f), > +}; > + > static const struct qmp_phy_init_tbl sm6115_ufsphy_serdes[] = { > QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x0e), > QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14), > @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = { > .regs = ufsphy_v5_regs_layout, > }; > > +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { > + .lanes = 2, > + > + .offsets = &qmp_ufs_offsets, > + > + .tbls = { > + .serdes = sm8150_ufsphy_serdes, > + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), > + .tx = sc7280_ufsphy_tx, > + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), > + .rx = sc7280_ufsphy_rx, > + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), > + .pcs = sc7280_ufsphy_pcs, > + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), > + }, > + .tbls_hs_b = { > + .serdes = sm8150_ufsphy_hs_b_serdes, > + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), > + }, > + .tbls_hs_g4 = { > + .tx = sm8250_ufsphy_hs_g4_tx, > + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), > + .rx = sc7280_ufsphy_hs_g4_rx, > + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), > + .pcs = sm8150_ufsphy_hs_g4_pcs, > + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), > + }, > + .clk_list = sm8450_ufs_phy_clk_l, > + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), > + .vreg_list = qmp_phy_vreg_l, > + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > + .regs = ufsphy_v4_regs_layout, > +}; > + > static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { > .lanes = 2, > > @@ -1648,6 +1787,9 @@ static const struct of_device_id qmp_ufs_of_match_table[] = { > }, { > .compatible = "qcom,sa8775p-qmp-ufs-phy", > .data = &sa8775p_ufsphy_cfg, > + }, { > + .compatible = "qcom,sc7280-qmp-ufs-phy", > + .data = &sc7280_ufsphy_cfg, > }, { > .compatible = "qcom,sc8180x-qmp-ufs-phy", > .data = &sm8150_ufsphy_cfg, > -- > 2.17.1 > Gentle reminder, kindly let me know any further comments. Thanks, Nitin
On 23/08/2023 12:17, Nitin Rawat wrote: > Add SC7280 specific register layout and table configs. > > Co-developed-by: Manish Pandey <quic_mapa@quicinc.com> > Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> > Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > --- > drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++ > 1 file changed, 142 insertions(+) > > diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > index 3927eba8e468..514fa14df634 100644 > --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c [skipped tables programming] 4), > @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = { > .regs = ufsphy_v5_regs_layout, > }; > > +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { > + .lanes = 2, > + > + .offsets = &qmp_ufs_offsets, > + > + .tbls = { > + .serdes = sm8150_ufsphy_serdes, > + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), > + .tx = sc7280_ufsphy_tx, > + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), > + .rx = sc7280_ufsphy_rx, > + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), > + .pcs = sc7280_ufsphy_pcs, > + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), > + }, > + .tbls_hs_b = { > + .serdes = sm8150_ufsphy_hs_b_serdes, > + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), > + }, > + .tbls_hs_g4 = { > + .tx = sm8250_ufsphy_hs_g4_tx, > + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), > + .rx = sc7280_ufsphy_hs_g4_rx, > + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), > + .pcs = sm8150_ufsphy_hs_g4_pcs, > + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), > + }, > + .clk_list = sm8450_ufs_phy_clk_l, > + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), This doesn't correspond to the bindings. This array has 3 enries, while in the bindings you have opted for two clocks for this PHY. > + .vreg_list = qmp_phy_vreg_l, > + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > + .regs = ufsphy_v4_regs_layout, > +}; > + > static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { > .lanes = 2, > > @@ -1648,6 +1787,9 @@ static const struct of_device_id qmp_ufs_of_match_table[] = { > }, { > .compatible = "qcom,sa8775p-qmp-ufs-phy", > .data = &sa8775p_ufsphy_cfg, > + }, { > + .compatible = "qcom,sc7280-qmp-ufs-phy", > + .data = &sc7280_ufsphy_cfg, > }, { > .compatible = "qcom,sc8180x-qmp-ufs-phy", > .data = &sm8150_ufsphy_cfg, > -- > 2.17.1 >
On 9/6/2023 1:34 AM, Dmitry Baryshkov wrote: > On 23/08/2023 12:17, Nitin Rawat wrote: >> Add SC7280 specific register layout and table configs. >> >> Co-developed-by: Manish Pandey <quic_mapa@quicinc.com> >> Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> >> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> >> --- >> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++ >> 1 file changed, 142 insertions(+) >> >> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >> b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >> index 3927eba8e468..514fa14df634 100644 >> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > > [skipped tables programming] > > 4), Sorry I quite didn't get this comment. what exactly is skipped ?Please can you help explain? >> @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg >> sa8775p_ufsphy_cfg = { >> .regs = ufsphy_v5_regs_layout, >> }; >> >> +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { >> + .lanes = 2, >> + >> + .offsets = &qmp_ufs_offsets, >> + >> + .tbls = { >> + .serdes = sm8150_ufsphy_serdes, >> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), >> + .tx = sc7280_ufsphy_tx, >> + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), >> + .rx = sc7280_ufsphy_rx, >> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), >> + .pcs = sc7280_ufsphy_pcs, >> + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), >> + }, >> + .tbls_hs_b = { >> + .serdes = sm8150_ufsphy_hs_b_serdes, >> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), >> + }, >> + .tbls_hs_g4 = { >> + .tx = sm8250_ufsphy_hs_g4_tx, >> + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), >> + .rx = sc7280_ufsphy_hs_g4_rx, >> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), >> + .pcs = sm8150_ufsphy_hs_g4_pcs, >> + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), >> + }, >> + .clk_list = sm8450_ufs_phy_clk_l, >> + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), > > This doesn't correspond to the bindings. This array has 3 enries, while > in the bindings you have opted for two clocks for this PHY. Sure. I'll update the bindings. > >> + .vreg_list = qmp_phy_vreg_l, >> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), >> + .regs = ufsphy_v4_regs_layout, >> +}; >> + >> static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { >> .lanes = 2, >> >> @@ -1648,6 +1787,9 @@ static const struct of_device_id >> qmp_ufs_of_match_table[] = { >> }, { >> .compatible = "qcom,sa8775p-qmp-ufs-phy", >> .data = &sa8775p_ufsphy_cfg, >> + }, { >> + .compatible = "qcom,sc7280-qmp-ufs-phy", >> + .data = &sc7280_ufsphy_cfg, >> }, { >> .compatible = "qcom,sc8180x-qmp-ufs-phy", >> .data = &sm8150_ufsphy_cfg, >> -- >> 2.17.1 >> > Thanks, Nitin
On Fri, 15 Sept 2023 at 19:14, Nitin Rawat <quic_nitirawa@quicinc.com> wrote: > > > > On 9/6/2023 1:34 AM, Dmitry Baryshkov wrote: > > On 23/08/2023 12:17, Nitin Rawat wrote: > >> Add SC7280 specific register layout and table configs. > >> > >> Co-developed-by: Manish Pandey <quic_mapa@quicinc.com> > >> Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> > >> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > >> --- > >> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++ > >> 1 file changed, 142 insertions(+) > >> > >> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >> b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >> index 3927eba8e468..514fa14df634 100644 > >> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > > > > [skipped tables programming] > > > > 4), > Sorry I quite didn't get this comment. what exactly is skipped ?Please > can you help explain? I skipped them, as I didn't have comments for them. > > > >> @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg > >> sa8775p_ufsphy_cfg = { > >> .regs = ufsphy_v5_regs_layout, > >> }; > >> > >> +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { > >> + .lanes = 2, > >> + > >> + .offsets = &qmp_ufs_offsets, > >> + > >> + .tbls = { > >> + .serdes = sm8150_ufsphy_serdes, > >> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), > >> + .tx = sc7280_ufsphy_tx, > >> + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), > >> + .rx = sc7280_ufsphy_rx, > >> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), > >> + .pcs = sc7280_ufsphy_pcs, > >> + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), > >> + }, > >> + .tbls_hs_b = { > >> + .serdes = sm8150_ufsphy_hs_b_serdes, > >> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), > >> + }, > >> + .tbls_hs_g4 = { > >> + .tx = sm8250_ufsphy_hs_g4_tx, > >> + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), > >> + .rx = sc7280_ufsphy_hs_g4_rx, > >> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), > >> + .pcs = sm8150_ufsphy_hs_g4_pcs, > >> + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), > >> + }, > >> + .clk_list = sm8450_ufs_phy_clk_l, > >> + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), > > > > This doesn't correspond to the bindings. This array has 3 enries, while > > in the bindings you have opted for two clocks for this PHY. > Sure. I'll update the bindings. Are you sure about the third clock? Neither sm8150 nor sm8250 used the qref clock. Or is that an omission on our side? > > > > >> + .vreg_list = qmp_phy_vreg_l, > >> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > >> + .regs = ufsphy_v4_regs_layout, > >> +}; > >> + > >> static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { > >> .lanes = 2, > >> > >> @@ -1648,6 +1787,9 @@ static const struct of_device_id > >> qmp_ufs_of_match_table[] = { > >> }, { > >> .compatible = "qcom,sa8775p-qmp-ufs-phy", > >> .data = &sa8775p_ufsphy_cfg, > >> + }, { > >> + .compatible = "qcom,sc7280-qmp-ufs-phy", > >> + .data = &sc7280_ufsphy_cfg, > >> }, { > >> .compatible = "qcom,sc8180x-qmp-ufs-phy", > >> .data = &sm8150_ufsphy_cfg, > >> -- > >> 2.17.1 > >> > > > Thanks, > Nitin
On 9/16/2023 12:03 AM, Dmitry Baryshkov wrote: > On Fri, 15 Sept 2023 at 19:14, Nitin Rawat <quic_nitirawa@quicinc.com> wrote: >> >> >> >> On 9/6/2023 1:34 AM, Dmitry Baryshkov wrote: >>> On 23/08/2023 12:17, Nitin Rawat wrote: >>>> Add SC7280 specific register layout and table configs. >>>> >>>> Co-developed-by: Manish Pandey <quic_mapa@quicinc.com> >>>> Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> >>>> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> >>>> --- >>>> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++ >>>> 1 file changed, 142 insertions(+) >>>> >>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >>>> b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >>>> index 3927eba8e468..514fa14df634 100644 >>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c >>> >>> [skipped tables programming] >>> >>> 4), >> Sorry I quite didn't get this comment. what exactly is skipped ?Please >> can you help explain? > > I skipped them, as I didn't have comments for them. > >> >> >>>> @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg >>>> sa8775p_ufsphy_cfg = { >>>> .regs = ufsphy_v5_regs_layout, >>>> }; >>>> >>>> +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { >>>> + .lanes = 2, >>>> + >>>> + .offsets = &qmp_ufs_offsets, >>>> + >>>> + .tbls = { >>>> + .serdes = sm8150_ufsphy_serdes, >>>> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), >>>> + .tx = sc7280_ufsphy_tx, >>>> + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), >>>> + .rx = sc7280_ufsphy_rx, >>>> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), >>>> + .pcs = sc7280_ufsphy_pcs, >>>> + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), >>>> + }, >>>> + .tbls_hs_b = { >>>> + .serdes = sm8150_ufsphy_hs_b_serdes, >>>> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), >>>> + }, >>>> + .tbls_hs_g4 = { >>>> + .tx = sm8250_ufsphy_hs_g4_tx, >>>> + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), >>>> + .rx = sc7280_ufsphy_hs_g4_rx, >>>> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), >>>> + .pcs = sm8150_ufsphy_hs_g4_pcs, >>>> + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), >>>> + }, >>>> + .clk_list = sm8450_ufs_phy_clk_l, >>>> + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), >>> >>> This doesn't correspond to the bindings. This array has 3 enries, while >>> in the bindings you have opted for two clocks for this PHY. >> Sure. I'll update the bindings. > > Are you sure about the third clock? Neither sm8150 nor sm8250 used the > qref clock. Or is that an omission on our side? > Hi Dmitry, For SC7280 we need all the three clocks for this target. Same is being used in downstream code as well. Hence I would need to update the binding as well. Thanks, Nitin >> >>> >>>> + .vreg_list = qmp_phy_vreg_l, >>>> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), >>>> + .regs = ufsphy_v4_regs_layout, >>>> +}; >>>> + >>>> static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { >>>> .lanes = 2, >>>> >>>> @@ -1648,6 +1787,9 @@ static const struct of_device_id >>>> qmp_ufs_of_match_table[] = { >>>> }, { >>>> .compatible = "qcom,sa8775p-qmp-ufs-phy", >>>> .data = &sa8775p_ufsphy_cfg, >>>> + }, { >>>> + .compatible = "qcom,sc7280-qmp-ufs-phy", >>>> + .data = &sc7280_ufsphy_cfg, >>>> }, { >>>> .compatible = "qcom,sc8180x-qmp-ufs-phy", >>>> .data = &sm8150_ufsphy_cfg, >>>> -- >>>> 2.17.1 >>>> >>> >> Thanks, >> Nitin > > >
On Sun, 17 Sept 2023 at 17:23, Nitin Rawat <quic_nitirawa@quicinc.com> wrote: > > > > On 9/16/2023 12:03 AM, Dmitry Baryshkov wrote: > > On Fri, 15 Sept 2023 at 19:14, Nitin Rawat <quic_nitirawa@quicinc.com> wrote: > >> > >> > >> > >> On 9/6/2023 1:34 AM, Dmitry Baryshkov wrote: > >>> On 23/08/2023 12:17, Nitin Rawat wrote: > >>>> Add SC7280 specific register layout and table configs. > >>>> > >>>> Co-developed-by: Manish Pandey <quic_mapa@quicinc.com> > >>>> Signed-off-by: Manish Pandey <quic_mapa@quicinc.com> > >>>> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com> > >>>> --- > >>>> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++ > >>>> 1 file changed, 142 insertions(+) > >>>> > >>>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >>>> b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >>>> index 3927eba8e468..514fa14df634 100644 > >>>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >>>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c > >>> > >>> [skipped tables programming] > >>> > >>> 4), > >> Sorry I quite didn't get this comment. what exactly is skipped ?Please > >> can you help explain? > > > > I skipped them, as I didn't have comments for them. > > > >> > >> > >>>> @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg > >>>> sa8775p_ufsphy_cfg = { > >>>> .regs = ufsphy_v5_regs_layout, > >>>> }; > >>>> > >>>> +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { > >>>> + .lanes = 2, > >>>> + > >>>> + .offsets = &qmp_ufs_offsets, > >>>> + > >>>> + .tbls = { > >>>> + .serdes = sm8150_ufsphy_serdes, > >>>> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), > >>>> + .tx = sc7280_ufsphy_tx, > >>>> + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), > >>>> + .rx = sc7280_ufsphy_rx, > >>>> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), > >>>> + .pcs = sc7280_ufsphy_pcs, > >>>> + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), > >>>> + }, > >>>> + .tbls_hs_b = { > >>>> + .serdes = sm8150_ufsphy_hs_b_serdes, > >>>> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), > >>>> + }, > >>>> + .tbls_hs_g4 = { > >>>> + .tx = sm8250_ufsphy_hs_g4_tx, > >>>> + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), > >>>> + .rx = sc7280_ufsphy_hs_g4_rx, > >>>> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), > >>>> + .pcs = sm8150_ufsphy_hs_g4_pcs, > >>>> + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), > >>>> + }, > >>>> + .clk_list = sm8450_ufs_phy_clk_l, > >>>> + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), > >>> > >>> This doesn't correspond to the bindings. This array has 3 enries, while > >>> in the bindings you have opted for two clocks for this PHY. > >> Sure. I'll update the bindings. > > > > Are you sure about the third clock? Neither sm8150 nor sm8250 used the > > qref clock. Or is that an omission on our side? > > > > Hi Dmitry, > > For SC7280 we need all the three clocks for this target. Same is being > used in downstream code as well. Hence I would need to update the > binding as well. Ack, thanks for the confirmation. > > Thanks, > Nitin > > > >> > >>> > >>>> + .vreg_list = qmp_phy_vreg_l, > >>>> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), > >>>> + .regs = ufsphy_v4_regs_layout, > >>>> +}; > >>>> + > >>>> static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { > >>>> .lanes = 2, > >>>> > >>>> @@ -1648,6 +1787,9 @@ static const struct of_device_id > >>>> qmp_ufs_of_match_table[] = { > >>>> }, { > >>>> .compatible = "qcom,sa8775p-qmp-ufs-phy", > >>>> .data = &sa8775p_ufsphy_cfg, > >>>> + }, { > >>>> + .compatible = "qcom,sc7280-qmp-ufs-phy", > >>>> + .data = &sc7280_ufsphy_cfg, > >>>> }, { > >>>> .compatible = "qcom,sc8180x-qmp-ufs-phy", > >>>> .data = &sm8150_ufsphy_cfg, > >>>> -- > >>>> 2.17.1 > >>>> > >>> > >> Thanks, > >> Nitin > > > > > > -- With best wishes Dmitry
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c index 3927eba8e468..514fa14df634 100644 --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c @@ -177,6 +177,111 @@ static const struct qmp_phy_init_tbl msm8996_ufsphy_rx[] = { QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0E), }; +static const struct qmp_phy_init_tbl sc7280_ufsphy_tx[] = { + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1, 0x03), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_3_DIVIDER_BAND0_1, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_4_DIVIDER_BAND0_1, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x35), + QMP_PHY_INIT_CFG(QSERDES_V4_TX_TRAN_DRVR_EMP_EN, 0x0c), +}; + +static const struct qmp_phy_init_tbl sc7280_ufsphy_rx[] = { + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0e), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x1b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x10), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x6d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x6d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xed), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x3c), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xe0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c), +}; + +static const struct qmp_phy_init_tbl sc7280_ufsphy_pcs[] = { + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_SIGDET_CTRL2, 0x6d), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0a), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_SMALL_AMP_DRV_LVL, 0x02), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_MID_TERM_CTRL1, 0x43), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_DEBUG_BUS_CLKSEL, 0x1f), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xff), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_MULTI_LANE_CTRL1, 0x02), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_PLL_CNTL, 0x03), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB, 0x16), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB, 0xd8), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_PWM_GEAR_BAND, 0xaa), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_HS_GEAR_BAND, 0x06), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x03), + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x03), +}; + +static const struct qmp_phy_init_tbl sc7280_ufsphy_hs_g4_rx[] = { + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x81), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0e), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x6f), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL1, 0x04), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x09), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x07), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x17), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x20), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0x80), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x01), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x3f), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xff), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x2c), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0x6d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0x6d), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xed), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x3c), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c), + QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x0f), +}; + static const struct qmp_phy_init_tbl sm6115_ufsphy_serdes[] = { QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x0e), QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14), @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = { .regs = ufsphy_v5_regs_layout, }; +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = { + .lanes = 2, + + .offsets = &qmp_ufs_offsets, + + .tbls = { + .serdes = sm8150_ufsphy_serdes, + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes), + .tx = sc7280_ufsphy_tx, + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx), + .rx = sc7280_ufsphy_rx, + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx), + .pcs = sc7280_ufsphy_pcs, + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs), + }, + .tbls_hs_b = { + .serdes = sm8150_ufsphy_hs_b_serdes, + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes), + }, + .tbls_hs_g4 = { + .tx = sm8250_ufsphy_hs_g4_tx, + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx), + .rx = sc7280_ufsphy_hs_g4_rx, + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx), + .pcs = sm8150_ufsphy_hs_g4_pcs, + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs), + }, + .clk_list = sm8450_ufs_phy_clk_l, + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l), + .vreg_list = qmp_phy_vreg_l, + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l), + .regs = ufsphy_v4_regs_layout, +}; + static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = { .lanes = 2, @@ -1648,6 +1787,9 @@ static const struct of_device_id qmp_ufs_of_match_table[] = { }, { .compatible = "qcom,sa8775p-qmp-ufs-phy", .data = &sa8775p_ufsphy_cfg, + }, { + .compatible = "qcom,sc7280-qmp-ufs-phy", + .data = &sc7280_ufsphy_cfg, }, { .compatible = "qcom,sc8180x-qmp-ufs-phy", .data = &sm8150_ufsphy_cfg,