@@ -390,6 +390,8 @@ static void __xr17v35x_unregister_gpio(struct platform_device *pdev)
platform_device_unregister(pdev);
}
+
+
static const struct property_entry exar_gpio_properties[] = {
PROPERTY_ENTRY_U32("exar,first-pin", 0),
PROPERTY_ENTRY_U32("ngpios", 16),
@@ -439,6 +441,35 @@ static int generic_rs485_config(struct uart_port *port, struct ktermios *termios
return 0;
}
+static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termios,
+ struct serial_rs485 *rs485)
+{
+ bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
+ u8 __iomem *p = port->membase;
+ u8 old_lcr;
+ generic_rs485_config(port, termios, rs485);
+
+ if (is_rs485) {
+ // Set EFR[4]=1 to enable enhanced feature registers
+ writeb(readb(p + UART_XR_EFR) | 0x10, p + 0x09);
+
+ // Set MCR to use DTR as Auto-RS485 Enable signal
+ writeb(0x04, p + UART_MCR);
+
+ // Store original LCR and set LCR[7]=1 to enable access to DLD register
+ old_lcr = readb(p + UART_LCR);
+ writeb(old_lcr | 0x80, p + UART_LCR);
+
+ // Set DLD[7]=1 for inverted RS485 Enable logic
+ writeb(readb(p + 0x02) | 0x80, p + 0x02);
+
+ // Reset LCR to orginal value
+ writeb(old_lcr, p + UART_LCR);
+ }
+
+ return 0;
+ }
+
static const struct serial_rs485 generic_rs485_supported = {
.flags = SER_RS485_ENABLED,
};
@@ -744,6 +775,19 @@ static int __maybe_unused exar_resume(struct device *dev)
return 0;
}
+static int pci_sealevel_setup(struct exar8250 *priv, struct pci_dev *pcidev,
+ struct uart_8250_port *port, int idx)
+{
+ int ret = pci_xr17v35x_setup(priv, pcidev, port, idx);
+
+ if (ret)
+ return ret;
+
+ port->port.rs485_config = sealevel_rs485_config;
+
+ return ret;
+}
+
static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
static const struct exar8250_board pbn_fastcom335_2 = {
@@ -809,6 +853,17 @@ static const struct exar8250_board pbn_exar_XR17V8358 = {
.exit = pci_xr17v35x_exit,
};
+static const struct exar8250_board pbn_sealevel = {
+ .setup = pci_sealevel_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
+static const struct exar8250_board pbn_sealevel_16 = {
+ .num_ports = 16,
+ .setup = pci_sealevel_setup,
+ .exit = pci_xr17v35x_exit,
+};
+
#define CONNECT_DEVICE(devid, sdevid, bd) { \
PCI_DEVICE_SUB( \
PCI_VENDOR_ID_EXAR, \
@@ -838,6 +893,15 @@ static const struct exar8250_board pbn_exar_XR17V8358 = {
(kernel_ulong_t)&bd \
}
+#define SEALEVEL_DEVICE(devid, bd) { \
+ PCI_DEVICE_SUB( \
+ PCI_VENDOR_ID_EXAR, \
+ PCI_DEVICE_ID_EXAR_##devid, \
+ PCI_VENDOR_ID_SEALEVEL, \
+ PCI_ANY_ID), 0, 0, \
+ (kernel_ulong_t)&bd \
+ }
+
static const struct pci_device_id exar_pci_tbl[] = {
EXAR_DEVICE(ACCESSIO, COM_2S, pbn_exar_XR17C15x),
EXAR_DEVICE(ACCESSIO, COM_4S, pbn_exar_XR17C15x),
@@ -886,6 +950,12 @@ static const struct pci_device_id exar_pci_tbl[] = {
EXAR_DEVICE(COMMTECH, 2324PCI335, pbn_fastcom335_4),
EXAR_DEVICE(COMMTECH, 2328PCI335, pbn_fastcom335_8),
+ SEALEVEL_DEVICE(XR17V352, pbn_sealevel),
+ SEALEVEL_DEVICE(XR17V354, pbn_sealevel),
+ SEALEVEL_DEVICE(XR17V358, pbn_sealevel),
+ SEALEVEL_DEVICE(XR17V4358, pbn_sealevel_16),
+ SEALEVEL_DEVICE(XR17V8358, pbn_sealevel_16),
+
{ 0, }
};
MODULE_DEVICE_TABLE(pci, exar_pci_tbl);