@@ -23,12 +23,6 @@ msm-$(CONFIG_DRM_MSM_HDMI) += \
hdmi/hdmi_bridge.o \
hdmi/hdmi_hpd.o \
hdmi/hdmi_i2c.o \
- hdmi/hdmi_phy.o \
- hdmi/hdmi_phy_8960.o \
- hdmi/hdmi_phy_8996.o \
- hdmi/hdmi_phy_8x60.o \
- hdmi/hdmi_phy_8x74.o \
- hdmi/hdmi_pll_8960.o \
msm-$(CONFIG_DRM_MSM_MDP4) += \
disp/mdp4/mdp4_crtc.o \
@@ -7,6 +7,7 @@
#include <linux/of_irq.h>
#include <linux/of_gpio.h>
+#include <linux/phy/phy.h>
#include <drm/drm_bridge_connector.h>
#include <drm/drm_of.h>
@@ -72,44 +73,6 @@ static void msm_hdmi_destroy(struct hdmi *hdmi)
msm_hdmi_i2c_destroy(hdmi->i2c);
}
-static void msm_hdmi_put_phy(struct hdmi *hdmi)
-{
- if (hdmi->phy_dev) {
- put_device(hdmi->phy_dev);
- hdmi->phy = NULL;
- hdmi->phy_dev = NULL;
- }
-}
-
-static int msm_hdmi_get_phy(struct hdmi *hdmi)
-{
- struct platform_device *pdev = hdmi->pdev;
- struct platform_device *phy_pdev;
- struct device_node *phy_node;
-
- phy_node = of_parse_phandle(pdev->dev.of_node, "phys", 0);
- if (!phy_node) {
- DRM_DEV_ERROR(&pdev->dev, "cannot find phy device\n");
- return -ENXIO;
- }
-
- phy_pdev = of_find_device_by_node(phy_node);
- of_node_put(phy_node);
-
- if (!phy_pdev)
- return dev_err_probe(&pdev->dev, -EPROBE_DEFER, "phy driver is not ready\n");
-
- hdmi->phy = platform_get_drvdata(phy_pdev);
- if (!hdmi->phy) {
- put_device(&phy_pdev->dev);
- return dev_err_probe(&pdev->dev, -EPROBE_DEFER, "phy driver is not ready\n");
- }
-
- hdmi->phy_dev = &phy_pdev->dev;
-
- return 0;
-}
-
/* construct hdmi at bind/probe time, grab all the resources. If
* we are to EPROBE_DEFER we want to do it here, rather than later
* at modeset_init() time
@@ -510,37 +473,32 @@ static int msm_hdmi_dev_probe(struct platform_device *pdev)
if (hdmi->hpd_gpiod)
gpiod_set_consumer_name(hdmi->hpd_gpiod, "HDMI_HPD");
- ret = msm_hdmi_get_phy(hdmi);
- if (ret) {
+ hdmi->phy = devm_phy_get(&pdev->dev, NULL);
+ if (IS_ERR(hdmi->phy)) {
DRM_DEV_ERROR(&pdev->dev, "failed to get phy\n");
- return ret;
+ return PTR_ERR(hdmi->phy);
}
ret = devm_pm_runtime_enable(&pdev->dev);
if (ret)
- goto err_put_phy;
+ goto err;
platform_set_drvdata(pdev, hdmi);
ret = component_add(&pdev->dev, &msm_hdmi_ops);
if (ret)
- goto err_put_phy;
+ goto err;
return 0;
-err_put_phy:
- msm_hdmi_put_phy(hdmi);
+err:
return ret;
}
static int msm_hdmi_dev_remove(struct platform_device *pdev)
{
- struct hdmi *hdmi = dev_get_drvdata(&pdev->dev);
-
component_del(&pdev->dev, &msm_hdmi_ops);
- msm_hdmi_put_phy(hdmi);
-
return 0;
}
@@ -565,12 +523,10 @@ static struct platform_driver msm_hdmi_driver = {
void __init msm_hdmi_register(void)
{
- msm_hdmi_phy_driver_register();
platform_driver_register(&msm_hdmi_driver);
}
void __exit msm_hdmi_unregister(void)
{
platform_driver_unregister(&msm_hdmi_driver);
- msm_hdmi_phy_driver_unregister();
}
@@ -19,7 +19,6 @@
#include "msm_drv.h"
#include "hdmi.xml.h"
-struct hdmi_phy;
struct hdmi_platform_config;
struct hdmi_audio {
@@ -56,8 +55,7 @@ struct hdmi {
struct gpio_desc *hpd_gpiod;
- struct hdmi_phy *phy;
- struct device *phy_dev;
+ struct phy *phy;
struct i2c_adapter *i2c;
struct drm_connector *connector;
@@ -125,74 +123,6 @@ static inline u32 hdmi_qfprom_read(struct hdmi *hdmi, u32 reg)
return msm_readl(hdmi->qfprom_mmio + reg);
}
-/*
- * hdmi phy:
- */
-
-enum hdmi_phy_type {
- MSM_HDMI_PHY_8x60,
- MSM_HDMI_PHY_8960,
- MSM_HDMI_PHY_8x74,
- MSM_HDMI_PHY_8996,
- MSM_HDMI_PHY_MAX,
-};
-
-struct hdmi_phy_cfg {
- enum hdmi_phy_type type;
- void (*powerup)(struct hdmi_phy *phy, unsigned long int pixclock);
- void (*powerdown)(struct hdmi_phy *phy);
- const char * const *reg_names;
- int num_regs;
- const char * const *clk_names;
- int num_clks;
-};
-
-extern const struct hdmi_phy_cfg msm_hdmi_phy_8x60_cfg;
-extern const struct hdmi_phy_cfg msm_hdmi_phy_8960_cfg;
-extern const struct hdmi_phy_cfg msm_hdmi_phy_8x74_cfg;
-extern const struct hdmi_phy_cfg msm_hdmi_phy_8996_cfg;
-
-struct hdmi_phy {
- struct platform_device *pdev;
- void __iomem *mmio;
- struct hdmi_phy_cfg *cfg;
- const struct hdmi_phy_funcs *funcs;
- struct regulator_bulk_data *regs;
- struct clk **clks;
-};
-
-static inline void hdmi_phy_write(struct hdmi_phy *phy, u32 reg, u32 data)
-{
- msm_writel(data, phy->mmio + reg);
-}
-
-static inline u32 hdmi_phy_read(struct hdmi_phy *phy, u32 reg)
-{
- return msm_readl(phy->mmio + reg);
-}
-
-int msm_hdmi_phy_resource_enable(struct hdmi_phy *phy);
-void msm_hdmi_phy_resource_disable(struct hdmi_phy *phy);
-void msm_hdmi_phy_powerup(struct hdmi_phy *phy, unsigned long int pixclock);
-void msm_hdmi_phy_powerdown(struct hdmi_phy *phy);
-void __init msm_hdmi_phy_driver_register(void);
-void __exit msm_hdmi_phy_driver_unregister(void);
-
-#ifdef CONFIG_COMMON_CLK
-int msm_hdmi_pll_8960_init(struct platform_device *pdev);
-int msm_hdmi_pll_8996_init(struct platform_device *pdev);
-#else
-static inline int msm_hdmi_pll_8960_init(struct platform_device *pdev)
-{
- return -ENODEV;
-}
-
-static inline int msm_hdmi_pll_8996_init(struct platform_device *pdev)
-{
- return -ENODEV;
-}
-#endif
-
/*
* audio:
*/
@@ -5,6 +5,7 @@
*/
#include <linux/delay.h>
+#include <linux/phy/phy.h>
#include <drm/drm_bridge_connector.h>
#include <drm/drm_edid.h>
@@ -32,17 +33,6 @@ static void msm_hdmi_power_on(struct drm_bridge *bridge)
ret = regulator_bulk_enable(config->pwr_reg_cnt, hdmi->pwr_regs);
if (ret)
DRM_DEV_ERROR(dev->dev, "failed to enable pwr regulator: %d\n", ret);
-
- if (hdmi->extp_clk) {
- DBG("pixclock: %lu", hdmi->pixclock);
- ret = clk_set_rate(hdmi->extp_clk, hdmi->pixclock);
- if (ret)
- DRM_DEV_ERROR(dev->dev, "failed to set extp clk rate: %d\n", ret);
-
- ret = clk_prepare_enable(hdmi->extp_clk);
- if (ret)
- DRM_DEV_ERROR(dev->dev, "failed to enable extp clk: %d\n", ret);
- }
}
static void power_off(struct drm_bridge *bridge)
@@ -58,9 +48,6 @@ static void power_off(struct drm_bridge *bridge)
*/
mdelay(16 + 4);
- if (hdmi->extp_clk)
- clk_disable_unprepare(hdmi->extp_clk);
-
ret = regulator_bulk_disable(config->pwr_reg_cnt, hdmi->pwr_regs);
if (ret)
DRM_DEV_ERROR(dev->dev, "failed to disable pwr regulator: %d\n", ret);
@@ -131,14 +118,21 @@ static void msm_hdmi_config_avi_infoframe(struct hdmi *hdmi)
static void msm_hdmi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
struct drm_bridge_state *old_bridge_state)
{
+ struct drm_atomic_state *state = old_bridge_state->base.state;
struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
struct hdmi *hdmi = hdmi_bridge->hdmi;
- struct hdmi_phy *phy = hdmi->phy;
+ struct drm_connector *connector;
+ union phy_configure_opts phy_opts;
+ int ret;
DBG("power up");
+ connector = drm_atomic_get_new_connector_for_encoder(state, bridge->encoder);
+ if (WARN_ON(!connector))
+ return;
+
if (!hdmi->power_on) {
- msm_hdmi_phy_resource_enable(phy);
+ phy_init(hdmi->phy);
msm_hdmi_power_on(bridge);
hdmi->power_on = true;
}
@@ -149,9 +143,27 @@ static void msm_hdmi_bridge_atomic_pre_enable(struct drm_bridge *bridge,
}
if (hdmi->phy_power_on)
- msm_hdmi_phy_powerdown(phy);
+ phy_power_off(hdmi->phy);
+
+ phy_opts.hdmi.pixel_clk_rate = hdmi->pixclock / 1000;
+ phy_opts.hdmi.bpc = connector->display_info.bpc;
+ phy_opts.hdmi.color_space = HDMI_PHY_COLORSPACE_RGB;
+ phy_configure(hdmi->phy, &phy_opts);
+
+ ret = phy_power_on(hdmi->phy);
+ if (WARN_ON(ret))
+ return;
+
+ if (hdmi->extp_clk) {
+ ret = clk_set_rate(hdmi->extp_clk, hdmi->pixclock);
+ if (ret)
+ DRM_DEV_ERROR(bridge->dev->dev, "failed to set extp clk rate: %d\n", ret);
+
+ ret = clk_prepare_enable(hdmi->extp_clk);
+ if (ret)
+ DRM_DEV_ERROR(bridge->dev->dev, "failed to enable extp clk: %d\n", ret);
+ }
- msm_hdmi_phy_powerup(phy, hdmi->pixclock);
hdmi->phy_power_on = true;
msm_hdmi_set_mode(hdmi, true);
@@ -165,7 +177,6 @@ static void msm_hdmi_bridge_atomic_post_disable(struct drm_bridge *bridge,
{
struct hdmi_bridge *hdmi_bridge = to_hdmi_bridge(bridge);
struct hdmi *hdmi = hdmi_bridge->hdmi;
- struct hdmi_phy *phy = hdmi->phy;
if (hdmi->hdcp_ctrl)
msm_hdmi_hdcp_off(hdmi->hdcp_ctrl);
@@ -173,7 +184,12 @@ static void msm_hdmi_bridge_atomic_post_disable(struct drm_bridge *bridge,
DBG("power down");
msm_hdmi_set_mode(hdmi, false);
- msm_hdmi_phy_powerdown(phy);
+ if (hdmi->phy_power_on) {
+ if (hdmi->extp_clk)
+ clk_disable_unprepare(hdmi->extp_clk);
+
+ phy_power_off(hdmi->phy);
+ }
hdmi->phy_power_on = false;
if (hdmi->power_on) {
@@ -181,7 +197,7 @@ static void msm_hdmi_bridge_atomic_post_disable(struct drm_bridge *bridge,
hdmi->power_on = false;
if (hdmi->hdmi_mode)
msm_hdmi_audio_update(hdmi);
- msm_hdmi_phy_resource_disable(phy);
+ phy_exit(hdmi->phy);
}
}
Change the MSM HDMI driver to use generic PHY subsystem. Moving PHY drivers allows better code sharing with the rest of the PHY system. Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- drivers/gpu/drm/msm/Makefile | 6 --- drivers/gpu/drm/msm/hdmi/hdmi.c | 58 +++------------------ drivers/gpu/drm/msm/hdmi/hdmi.h | 72 +------------------------- drivers/gpu/drm/msm/hdmi/hdmi_bridge.c | 58 +++++++++++++-------- 4 files changed, 45 insertions(+), 149 deletions(-)