@@ -251,11 +251,16 @@
#define MUSTAT_IRDYN 0x80 /* 0 = MIDI data or command ACK */
#define MUSTAT_ORDYN 0x40 /* 0 = MUDATA can accept a command or data */
-#define A_IOCFG 0x18 /* GPIO on Audigy card (16bits) */
+#define A_GPIO 0x18 /* GPIO on Audigy card (16bits) */
#define A_GPINPUT_MASK 0xff00
#define A_GPOUTPUT_MASK 0x00ff
+// The GPIO port is used for I/O config on Sound Blasters;
+// card-specific info can be found in the emu_chip_details table.
+// On E-MU cards the port is used as the interface to the FPGA.
+
// Audigy output/GPIO stuff taken from the kX drivers
+#define A_IOCFG A_GPIO
#define A_IOCFG_GPOUT0 0x0044 /* analog/digital */
#define A_IOCFG_DISABLE_ANALOG 0x0040 /* = 'enable' for Audigy2 (chiprev=4) */
#define A_IOCFG_ENABLE_DIGITAL 0x0004
@@ -223,8 +223,8 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir, int resume)
*/
outl(0x7a0000, emu->port + 0x20);
outl(0xFF000000, emu->port + 0x24);
- tmp = inl(emu->port + A_IOCFG) & ~0x8; /* Clear bit 3 */
- outl(tmp, emu->port + A_IOCFG);
+ tmp = inw(emu->port + A_IOCFG) & ~0x8; /* Clear bit 3 */
+ outw(tmp, emu->port + A_IOCFG);
}
if (emu->card_capabilities->spi_dac) { /* Audigy 2 ZS Notebook with DAC Wolfson WM8768/WM8568 */
int size, n;
@@ -244,15 +244,15 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir, int resume)
* GPIO6: Unknown
* GPIO7: Unknown
*/
- outl(0x76, emu->port + A_IOCFG); /* Windows uses 0x3f76 */
+ outw(0x76, emu->port + A_IOCFG); /* Windows uses 0x3f76 */
}
if (emu->card_capabilities->i2c_adc) { /* Audigy 2 ZS Notebook with ADC Wolfson WM8775 */
int size, n;
snd_emu10k1_ptr20_write(emu, P17V_I2S_SRC_SEL, 0, 0x2020205f);
- tmp = inl(emu->port + A_IOCFG);
- outl(tmp | 0x4, emu->port + A_IOCFG); /* Set bit 2 for mic input */
- tmp = inl(emu->port + A_IOCFG);
+ tmp = inw(emu->port + A_IOCFG);
+ outw(tmp | 0x4, emu->port + A_IOCFG); /* Set bit 2 for mic input */
+ tmp = inw(emu->port + A_IOCFG);
size = ARRAY_SIZE(i2c_adc_init);
for (n = 0; n < size; n++)
snd_emu10k1_i2c_write(emu, i2c_adc_init[n][0], i2c_adc_init[n][1]);
@@ -308,12 +308,12 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir, int resume)
} else if (emu->card_capabilities->i2c_adc) {
; /* Disable A_IOCFG for Audigy 2 ZS Notebook */
} else if (emu->audigy) {
- unsigned int reg = inl(emu->port + A_IOCFG);
- outl(reg | A_IOCFG_GPOUT2, emu->port + A_IOCFG);
+ u16 reg = inw(emu->port + A_IOCFG);
+ outw(reg | A_IOCFG_GPOUT2, emu->port + A_IOCFG);
udelay(500);
- outl(reg | A_IOCFG_GPOUT1 | A_IOCFG_GPOUT2, emu->port + A_IOCFG);
+ outw(reg | A_IOCFG_GPOUT1 | A_IOCFG_GPOUT2, emu->port + A_IOCFG);
udelay(100);
- outl(reg, emu->port + A_IOCFG);
+ outw(reg, emu->port + A_IOCFG);
} else {
unsigned int reg = inl(emu->port + HCFG);
outl(reg | HCFG_GPOUT2, emu->port + HCFG);
@@ -329,8 +329,8 @@ static int snd_emu10k1_init(struct snd_emu10k1 *emu, int enable_ir, int resume)
} else if (emu->card_capabilities->i2c_adc) {
; /* Disable A_IOCFG for Audigy 2 ZS Notebook */
} else if (emu->audigy) { /* enable analog output */
- unsigned int reg = inl(emu->port + A_IOCFG);
- outl(reg | A_IOCFG_GPOUT0, emu->port + A_IOCFG);
+ u16 reg = inw(emu->port + A_IOCFG);
+ outw(reg | A_IOCFG_GPOUT0, emu->port + A_IOCFG);
}
if (emu->address_mode == 0) {
@@ -354,19 +354,19 @@ static void snd_emu10k1_audio_enable(struct snd_emu10k1 *emu)
} else if (emu->card_capabilities->i2c_adc) {
; /* Disable A_IOCFG for Audigy 2 ZS Notebook */
} else if (emu->audigy) {
- outl(inl(emu->port + A_IOCFG) & ~0x44, emu->port + A_IOCFG);
+ outw(inw(emu->port + A_IOCFG) & ~0x44, emu->port + A_IOCFG);
if (emu->card_capabilities->ca0151_chip) { /* audigy2 */
/* Unmute Analog now. Set GPO6 to 1 for Apollo.
* This has to be done after init ALice3 I2SOut beyond 48KHz.
* So, sequence is important. */
- outl(inl(emu->port + A_IOCFG) | 0x0040, emu->port + A_IOCFG);
+ outw(inw(emu->port + A_IOCFG) | 0x0040, emu->port + A_IOCFG);
} else if (emu->card_capabilities->ca0108_chip) { /* audigy2 value */
/* Unmute Analog now. */
- outl(inl(emu->port + A_IOCFG) | 0x0060, emu->port + A_IOCFG);
+ outw(inw(emu->port + A_IOCFG) | 0x0060, emu->port + A_IOCFG);
} else {
/* Disable routing from AC97 line out to Front speakers */
- outl(inl(emu->port + A_IOCFG) | 0x0080, emu->port + A_IOCFG);
+ outw(inw(emu->port + A_IOCFG) | 0x0080, emu->port + A_IOCFG);
}
}
@@ -651,9 +651,9 @@ static int snd_emu1010_load_firmware_entry(struct snd_emu10k1 *emu,
const struct firmware *fw_entry)
{
int n, i;
- int reg;
- int value;
- __always_unused unsigned int write_post;
+ u16 reg;
+ u8 value;
+ __always_unused u16 write_post;
unsigned long flags;
if (!fw_entry)
@@ -666,28 +666,28 @@ static int snd_emu1010_load_firmware_entry(struct snd_emu10k1 *emu,
* FPGA CONFIG OFF -> FPGA PGMN
*/
spin_lock_irqsave(&emu->emu_lock, flags);
- outl(0x00, emu->port + A_IOCFG); /* Set PGMN low for 1uS. */
- write_post = inl(emu->port + A_IOCFG);
+ outw(0x00, emu->port + A_GPIO); /* Set PGMN low for 1uS. */
+ write_post = inw(emu->port + A_GPIO);
udelay(100);
- outl(0x80, emu->port + A_IOCFG); /* Leave bit 7 set during netlist setup. */
- write_post = inl(emu->port + A_IOCFG);
+ outw(0x80, emu->port + A_GPIO); /* Leave bit 7 set during netlist setup. */
+ write_post = inw(emu->port + A_GPIO);
udelay(100); /* Allow FPGA memory to clean */
for (n = 0; n < fw_entry->size; n++) {
value = fw_entry->data[n];
for (i = 0; i < 8; i++) {
reg = 0x80;
if (value & 0x1)
reg = reg | 0x20;
value = value >> 1;
- outl(reg, emu->port + A_IOCFG);
- write_post = inl(emu->port + A_IOCFG);
- outl(reg | 0x40, emu->port + A_IOCFG);
- write_post = inl(emu->port + A_IOCFG);
+ outw(reg, emu->port + A_GPIO);
+ write_post = inw(emu->port + A_GPIO);
+ outw(reg | 0x40, emu->port + A_GPIO);
+ write_post = inw(emu->port + A_GPIO);
}
}
/* After programming, set GPIO bit 4 high again. */
- outl(0x10, emu->port + A_IOCFG);
- write_post = inl(emu->port + A_IOCFG);
+ outw(0x10, emu->port + A_GPIO);
+ write_post = inw(emu->port + A_GPIO);
spin_unlock_irqrestore(&emu->emu_lock, flags);
return 0;
@@ -2054,7 +2054,7 @@ void snd_emu10k1_suspend_regs(struct snd_emu10k1 *emu)
*val = snd_emu10k1_ptr_read(emu, *reg, i);
}
if (emu->audigy)
- emu->saved_a_iocfg = inl(emu->port + A_IOCFG);
+ emu->saved_a_iocfg = inw(emu->port + A_IOCFG);
emu->saved_hcfg = inl(emu->port + HCFG);
}
@@ -2081,7 +2081,7 @@ void snd_emu10k1_resume_regs(struct snd_emu10k1 *emu)
/* resore for spdif */
if (emu->audigy)
- outl(emu->saved_a_iocfg, emu->port + A_IOCFG);
+ outw(emu->saved_a_iocfg, emu->port + A_IOCFG);
outl(emu->saved_hcfg, emu->port + HCFG);
val = emu->saved_ptr;
@@ -924,7 +924,7 @@ static int snd_audigy_i2c_capture_source_put(struct snd_kcontrol *kcontrol,
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
unsigned int source_id;
unsigned int ngain, ogain;
- u32 gpio;
+ u16 gpio;
int change = 0;
unsigned long flags;
u32 source;
@@ -941,11 +941,11 @@ static int snd_audigy_i2c_capture_source_put(struct snd_kcontrol *kcontrol,
if (change) {
snd_emu10k1_i2c_write(emu, ADC_MUX, 0); /* Mute input */
spin_lock_irqsave(&emu->emu_lock, flags);
- gpio = inl(emu->port + A_IOCFG);
+ gpio = inw(emu->port + A_IOCFG);
if (source_id==0)
- outl(gpio | 0x4, emu->port + A_IOCFG);
+ outw(gpio | 0x4, emu->port + A_IOCFG);
else
- outl(gpio & ~0x4, emu->port + A_IOCFG);
+ outw(gpio & ~0x4, emu->port + A_IOCFG);
spin_unlock_irqrestore(&emu->emu_lock, flags);
ngain = emu->i2c_capture_volume[source_id][0]; /* Left */
@@ -1632,7 +1632,7 @@ static int snd_emu10k1_shared_spdif_get(struct snd_kcontrol *kcontrol,
struct snd_emu10k1 *emu = snd_kcontrol_chip(kcontrol);
if (emu->audigy)
- ucontrol->value.integer.value[0] = inl(emu->port + A_IOCFG) & A_IOCFG_GPOUT0 ? 1 : 0;
+ ucontrol->value.integer.value[0] = inw(emu->port + A_IOCFG) & A_IOCFG_GPOUT0 ? 1 : 0;
else
ucontrol->value.integer.value[0] = inl(emu->port + HCFG) & HCFG_GPOUT0 ? 1 : 0;
if (emu->card_capabilities->invert_shared_spdif)
@@ -1657,13 +1657,13 @@ static int snd_emu10k1_shared_spdif_put(struct snd_kcontrol *kcontrol,
if ( emu->card_capabilities->i2c_adc) {
/* Do nothing for Audigy 2 ZS Notebook */
} else if (emu->audigy) {
- reg = inl(emu->port + A_IOCFG);
+ reg = inw(emu->port + A_IOCFG);
val = sw ? A_IOCFG_GPOUT0 : 0;
change = (reg & A_IOCFG_GPOUT0) != val;
if (change) {
reg &= ~A_IOCFG_GPOUT0;
reg |= val;
- outl(reg | val, emu->port + A_IOCFG);
+ outw(reg | val, emu->port + A_IOCFG);
}
}
reg = inl(emu->port + HCFG);
@@ -243,28 +243,28 @@ void snd_emu1010_fpga_write(struct snd_emu10k1 *emu, u32 reg, u32 value)
if (snd_BUG_ON(value > 0x3f)) /* 0 to 0x3f are values */
return;
spin_lock_irqsave(&emu->emu_lock, flags);
- outl(reg, emu->port + A_IOCFG);
+ outw(reg, emu->port + A_GPIO);
udelay(10);
- outl(reg | 0x80, emu->port + A_IOCFG); /* High bit clocks the value into the fpga. */
+ outw(reg | 0x80, emu->port + A_GPIO); /* High bit clocks the value into the fpga. */
udelay(10);
- outl(value, emu->port + A_IOCFG);
+ outw(value, emu->port + A_GPIO);
udelay(10);
- outl(value | 0x80 , emu->port + A_IOCFG); /* High bit clocks the value into the fpga. */
+ outw(value | 0x80 , emu->port + A_GPIO); /* High bit clocks the value into the fpga. */
spin_unlock_irqrestore(&emu->emu_lock, flags);
}
void snd_emu1010_fpga_read(struct snd_emu10k1 *emu, u32 reg, u32 *value)
{
unsigned long flags;
if (snd_BUG_ON(reg > 0x3f))
return;
reg += 0x40; /* 0x40 upwards are registers. */
spin_lock_irqsave(&emu->emu_lock, flags);
- outl(reg, emu->port + A_IOCFG);
+ outw(reg, emu->port + A_GPIO);
udelay(10);
- outl(reg | 0x80, emu->port + A_IOCFG); /* High bit clocks the value into the fpga. */
+ outw(reg | 0x80, emu->port + A_GPIO); /* High bit clocks the value into the fpga. */
udelay(10);
- *value = ((inl(emu->port + A_IOCFG) >> 8) & 0x7f);
+ *value = ((inw(emu->port + A_GPIO) >> 8) & 0x7f);
spin_unlock_irqrestore(&emu->emu_lock, flags);
}
As the register definition clearly states, this is a 16-bit register, yet we did all accesses as 32-bit. The writes in particular would have the potential to clear the TIMER register (depending on how the bus/card actually handles the too long writes). This commit also introduces a separate define A_GPIO which aliases A_IOCFG, which better reflects the distinct usage on E-MU cards. This is done in the same commit to keep the churn down, as we're touching all involved lines anyway. Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de> --- include/sound/emu10k1.h | 7 +++- sound/pci/emu10k1/emu10k1_main.c | 62 ++++++++++++++++---------------- sound/pci/emu10k1/emumixer.c | 14 ++++---- sound/pci/emu10k1/io.c | 14 ++++---- 4 files changed, 51 insertions(+), 46 deletions(-)