@@ -25,7 +25,14 @@ properties:
maxItems: 3
resets:
- maxItems: 1
+ minItems: 1
+ maxItems: 2
+
+ reset-names:
+ items:
+ - const: mcu_rst
+ - const: hold_boot
+ minItems: 1
st,syscfg-holdboot:
description: remote processor reset hold boot
@@ -36,16 +43,6 @@ properties:
- description: The offset of the hold boot setting register
- description: The field mask of the hold boot
- st,syscfg-tz:
- description:
- Reference to the system configuration which holds the RCC trust zone mode
- $ref: "/schemas/types.yaml#/definitions/phandle-array"
- items:
- - items:
- - description: Phandle of syscon block
- - description: The offset of the trust zone setting register
- - description: The field mask of the trust zone state
-
interrupts:
description: Should contain the WWDG1 watchdog reset interrupt
maxItems: 1
@@ -135,22 +132,47 @@ required:
- compatible
- reg
- resets
- - st,syscfg-holdboot
- - st,syscfg-tz
+ - reset-names
+
+allOf:
+ - if:
+ properties:
+ reset-names:
+ not:
+ contains:
+ const: hold_boot
+ then:
+ required:
+ - st,syscfg-holdboot
+ else:
+ properties:
+ st,syscfg-holdboot: false
additionalProperties: false
examples:
- |
#include <dt-bindings/reset/stm32mp1-resets.h>
- m4_rproc: m4@10000000 {
+ m4_rproc_example1: m4@10000000 {
compatible = "st,stm32mp1-m4";
reg = <0x10000000 0x40000>,
<0x30000000 0x40000>,
<0x38000000 0x10000>;
resets = <&rcc MCU_R>;
+ reset-names = "mcu_rst";
st,syscfg-holdboot = <&rcc 0x10C 0x1>;
- st,syscfg-tz = <&rcc 0x000 0x1>;
+ st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
+ st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
+ };
+ - |
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ m4_rproc_example2: m4@10000000 {
+ compatible = "st,stm32mp1-m4";
+ reg = <0x10000000 0x40000>,
+ <0x30000000 0x40000>,
+ <0x38000000 0x10000>;
+ resets = <&scmi MCU_R>, <&scmi MCU_HOLD_BOOT_R>;
+ reset-names = "mcu_rst", "hold_boot";
st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
};
With the introduction of the SCMI server it is now possible to use the SCMI to handle the hold boot instead of a dedicated smc call. As consequences two configurations are possible: - use the Linux rcc reset service and use syscon for the MCU hold boot - use the SCMI reset service for both the MCU reset and the MCU hold boot. This patch: - suppresses the use of the property st,syscfg-tz which was used to check if the trusted Zone was enable to use scm call to manage the hold boot (the reset controller phandle is used instead to select the configurations) - adds properties check on resets definitions. - adds an example of the SCMI reset service usage. Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> --- .../bindings/remoteproc/st,stm32-rproc.yaml | 52 +++++++++++++------ 1 file changed, 37 insertions(+), 15 deletions(-)