| Message ID | 20230315104411.73614-6-minda.chen@starfivetech.com |
|---|---|
| State | New |
| Headers | show |
| Series | Add JH7110 USB and USB PHY driver support | expand |
On 23-03-15 18:44:11, Minda Chen wrote: > USB Glue layer and Cadence USB subnode configuration, > also includes USB and PCIe phy dts configuration. > > Signed-off-by: Minda Chen <minda.chen@starfivetech.com> > --- > .../jh7110-starfive-visionfive-2.dtsi | 7 +++ > arch/riscv/boot/dts/starfive/jh7110.dtsi | 54 +++++++++++++++++++ > 2 files changed, 61 insertions(+) > > diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi > index a132debb9b53..c64476aebc1a 100644 > --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi > +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi > @@ -236,3 +236,10 @@ > pinctrl-0 = <&uart0_pins>; > status = "okay"; > }; > + > +&usb0 { > + status = "okay"; > + usbdrd_cdns3: usb@0 { > + dr_mode = "peripheral"; > + }; > +}; > diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi > index f70a4ed47eb4..17722fd1be62 100644 > --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi > +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi > @@ -362,6 +362,60 @@ > status = "disabled"; > }; > > + usb0: usb@10100000 { > + compatible = "starfive,jh7110-usb"; > + clocks = <&stgcrg JH7110_STGCLK_USB0_LPM>, > + <&stgcrg JH7110_STGCLK_USB0_STB>, > + <&stgcrg JH7110_STGCLK_USB0_APB>, > + <&stgcrg JH7110_STGCLK_USB0_AXI>, > + <&stgcrg JH7110_STGCLK_USB0_UTMI_APB>; > + clock-names = "lpm", "stb", "apb", "axi", "utmi_apb"; > + resets = <&stgcrg JH7110_STGRST_USB0_PWRUP>, > + <&stgcrg JH7110_STGRST_USB0_APB>, > + <&stgcrg JH7110_STGRST_USB0_AXI>, > + <&stgcrg JH7110_STGRST_USB0_UTMI_APB>; > + starfive,stg-syscon = <&stg_syscon 0x4 0xc4 0x148 0x1f4>; > + starfive,sys-syscon = <&sys_syscon 0x18>; > + status = "disabled"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0x0 0x0 0x10100000 0x100000>; Why it is four entry at ranges? Your address-cells and size-cells are both 1, and your binding-doc is also three? Peter > + > + usbdrd_cdns3: usb@0 { > + compatible = "cdns,usb3"; > + reg = <0x0 0x10000>, > + <0x10000 0x10000>, > + <0x20000 0x10000>; > + reg-names = "otg", "xhci", "dev"; > + interrupts = <100>, <108>, <110>; > + interrupt-names = "host", "peripheral", "otg"; > + phys = <&usbphy0>; > + phy-names = "cdns3,usb2-phy"; > + maximum-speed = "super-speed"; > + }; > + }; > + > + usbphy0: phy@10200000 { > + compatible = "starfive,jh7110-usb-phy"; > + reg = <0x0 0x10200000 0x0 0x10000>; > + clocks = <&syscrg JH7110_SYSCLK_USB_125M>, > + <&stgcrg JH7110_STGCLK_USB0_APP_125>; > + clock-names = "125m", "app_125"; > + #phy-cells = <0>; > + }; > + > + pciephy0: phy@10210000 { > + compatible = "starfive,jh7110-pcie-phy"; > + reg = <0x0 0x10210000 0x0 0x10000>; > + #phy-cells = <0>; > + }; > + > + pciephy1: phy@10220000 { > + compatible = "starfive,jh7110-pcie-phy"; > + reg = <0x0 0x10220000 0x0 0x10000>; > + #phy-cells = <0>; > + }; > + > stgcrg: clock-controller@10230000 { > compatible = "starfive,jh7110-stgcrg"; > reg = <0x0 0x10230000 0x0 0x10000>; > -- > 2.17.1 >
diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi index a132debb9b53..c64476aebc1a 100644 --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi @@ -236,3 +236,10 @@ pinctrl-0 = <&uart0_pins>; status = "okay"; }; + +&usb0 { + status = "okay"; + usbdrd_cdns3: usb@0 { + dr_mode = "peripheral"; + }; +}; diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi index f70a4ed47eb4..17722fd1be62 100644 --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi @@ -362,6 +362,60 @@ status = "disabled"; }; + usb0: usb@10100000 { + compatible = "starfive,jh7110-usb"; + clocks = <&stgcrg JH7110_STGCLK_USB0_LPM>, + <&stgcrg JH7110_STGCLK_USB0_STB>, + <&stgcrg JH7110_STGCLK_USB0_APB>, + <&stgcrg JH7110_STGCLK_USB0_AXI>, + <&stgcrg JH7110_STGCLK_USB0_UTMI_APB>; + clock-names = "lpm", "stb", "apb", "axi", "utmi_apb"; + resets = <&stgcrg JH7110_STGRST_USB0_PWRUP>, + <&stgcrg JH7110_STGRST_USB0_APB>, + <&stgcrg JH7110_STGRST_USB0_AXI>, + <&stgcrg JH7110_STGRST_USB0_UTMI_APB>; + starfive,stg-syscon = <&stg_syscon 0x4 0xc4 0x148 0x1f4>; + starfive,sys-syscon = <&sys_syscon 0x18>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x10100000 0x100000>; + + usbdrd_cdns3: usb@0 { + compatible = "cdns,usb3"; + reg = <0x0 0x10000>, + <0x10000 0x10000>, + <0x20000 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <100>, <108>, <110>; + interrupt-names = "host", "peripheral", "otg"; + phys = <&usbphy0>; + phy-names = "cdns3,usb2-phy"; + maximum-speed = "super-speed"; + }; + }; + + usbphy0: phy@10200000 { + compatible = "starfive,jh7110-usb-phy"; + reg = <0x0 0x10200000 0x0 0x10000>; + clocks = <&syscrg JH7110_SYSCLK_USB_125M>, + <&stgcrg JH7110_STGCLK_USB0_APP_125>; + clock-names = "125m", "app_125"; + #phy-cells = <0>; + }; + + pciephy0: phy@10210000 { + compatible = "starfive,jh7110-pcie-phy"; + reg = <0x0 0x10210000 0x0 0x10000>; + #phy-cells = <0>; + }; + + pciephy1: phy@10220000 { + compatible = "starfive,jh7110-pcie-phy"; + reg = <0x0 0x10220000 0x0 0x10000>; + #phy-cells = <0>; + }; + stgcrg: clock-controller@10230000 { compatible = "starfive,jh7110-stgcrg"; reg = <0x0 0x10230000 0x0 0x10000>;
USB Glue layer and Cadence USB subnode configuration, also includes USB and PCIe phy dts configuration. Signed-off-by: Minda Chen <minda.chen@starfivetech.com> --- .../jh7110-starfive-visionfive-2.dtsi | 7 +++ arch/riscv/boot/dts/starfive/jh7110.dtsi | 54 +++++++++++++++++++ 2 files changed, 61 insertions(+)