new file mode 100644
@@ -0,0 +1,152 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/samsung,exynos4210-fimc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S5P/Exynos SoC Fully Integrated Mobile Camera
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+ - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+description:
+ Each FIMC device should have an alias in the aliases node, in the form of
+ fimc<n>, where <n> is an integer specifying the IP block instance.
+
+properties:
+ compatible:
+ enum:
+ - samsung,exynos4210-fimc
+ - samsung,exynos4212-fimc
+ - samsung,s5pv210-fimc
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: fimc
+ - const: sclk_fimc
+
+ clock-frequency:
+ description:
+ Maximum FIMC local clock (LCLK) frequency.
+
+ interrupts:
+ maxItems: 1
+
+ iommus:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ samsung,cam-if:
+ type: boolean
+ description:
+ The FIMC IP block includes the camera input interface.
+
+ samsung,isp-wb:
+ type: boolean
+ description: |
+ The FIMC IP block has the ISP writeback input.
+
+ samsung,lcd-wb:
+ type: boolean
+ description: |
+ The FIMC IP block has the LCD writeback input.
+
+ samsung,mainscaler-ext:
+ type: boolean
+ description:
+ FIMC IP supports extended image size and has CIEXTEN register.
+
+ samsung,min-pix-alignment:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ - description: Minimum supported image height alignment.
+ - description: Horizontal image offset.
+ description:
+ The values are in pixels and default is <2 1>.
+
+ samsung,min-pix-sizes:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 2
+ description: |
+ An array specyfing minimum image size in pixels at the FIMC input and
+ output DMA, in the first and second cell respectively. Default value
+ is <16 16>.
+
+ samsung,pix-limits:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ maxItems: 4
+ description: |
+ An array of maximum supported image sizes in pixels, for details refer to
+ Table 2-1 in the S5PV210 SoC User Manual. The meaning of each cell is as
+ follows:
+ 0 - scaler input horizontal size
+ 1 - input horizontal size for the scaler bypassed
+ 2 - REAL_WIDTH without input rotation
+ 3 - REAL_HEIGHT with input rotation
+
+ samsung,rotators:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0x11
+ description: |
+ A bitmask specifying whether this IP has the input and the output
+ rotator. Bits 4 and 0 correspond to input and output rotator
+ respectively. If a rotator is present its corresponding bit should be
+ set.
+
+ samsung,sysreg:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ System Registers (SYSREG) node.
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - samsung,pix-limits
+
+allOf:
+ - if:
+ required:
+ - samsung,isp-wb
+ then:
+ required:
+ - samsung,sysreg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/exynos4.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ fimc@11800000 {
+ compatible = "samsung,exynos4212-fimc";
+ reg = <0x11800000 0x1000>;
+ clocks = <&clock CLK_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ clock-names = "fimc", "sclk_fimc";
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ iommus = <&sysmmu_fimc0>;
+ power-domains = <&pd_cam>;
+ samsung,sysreg = <&sys_reg>;
+
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,cam-if;
+
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+ };
new file mode 100644
@@ -0,0 +1,279 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/samsung,fimc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S5P/Exynos SoC Camera Subsystem (FIMC)
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+ - Sylwester Nawrocki <s.nawrocki@samsung.com>
+
+description: |
+ The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices
+ represented by separate device tree nodes. Currently this includes: Fully
+ Integrated Mobile Camera (FIMC, in the S5P SoCs series known as CAMIF), MIPI
+ CSIS, FIMC-LITE and FIMC-IS (ISP).
+
+properties:
+ compatible:
+ const: samsung,fimc
+
+ ranges: true
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 1
+
+ '#clock-cells':
+ const: 1
+ description: |
+ The clock specifier cell stores an index of a clock: 0, 1 for
+ CAM_A_CLKOUT, CAM_B_CLKOUT clocks respectively.
+
+ clocks:
+ minItems: 2
+ maxItems: 4
+
+ clock-names:
+ minItems: 2
+ items:
+ - const: sclk_cam0
+ - const: sclk_cam1
+ - const: pxl_async0
+ - const: pxl_async1
+
+ clock-output-names:
+ maxItems: 2
+
+ parallel-ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ description:
+ Active parallel video input ports.
+
+ patternProperties:
+ "^port@[01]$":
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ description:
+ Camera A and camera B inputs.
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ pinctrl-names:
+ minItems: 1
+ items:
+ - const: default
+ - const: idle
+ - const: active_a
+ - const: active_b
+
+patternProperties:
+ "^csis@[0-9a-f]+$":
+ type: object
+ $ref: samsung,exynos4210-csis.yaml#
+ description: MIPI CSI-2 receiver.
+
+ "^fimc@[0-9a-f]+$":
+ type: object
+ $ref: samsung,exynos4210-fimc.yaml#
+ description: Fully Integrated Mobile Camera.
+
+ "^fimc-is@[0-9a-f]+$":
+ type: object
+ $ref: samsung,exynos4212-fimc-is.yaml#
+ description: Imaging Subsystem (FIMC-IS).
+
+ "^fimc-lite@[0-9a-f]+$":
+ type: object
+ $ref: samsung,exynos4212-fimc-lite.yaml#
+ description: Camera host interface (FIMC-LITE).
+
+required:
+ - compatible
+ - '#address-cells'
+ - '#clock-cells'
+ - clocks
+ - clock-names
+ - clock-output-names
+ - ranges
+ - '#size-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/exynos4.h>
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ camera@11800000 {
+ compatible = "samsung,fimc";
+ #clock-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x18000000>;
+
+ clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>,
+ <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
+ clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
+ clock-output-names = "cam_a_clkout", "cam_b_clkout";
+
+ assigned-clocks = <&clock CLK_MOUT_CAM0>,
+ <&clock CLK_MOUT_CAM1>;
+ assigned-clock-parents = <&clock CLK_XUSBXTI>,
+ <&clock CLK_XUSBXTI>;
+
+ pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
+ pinctrl-names = "default";
+
+ fimc@11800000 {
+ compatible = "samsung,exynos4212-fimc";
+ reg = <0x11800000 0x1000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clock CLK_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ clock-names = "fimc", "sclk_fimc";
+ power-domains = <&pd_cam>;
+ samsung,sysreg = <&sys_reg>;
+ iommus = <&sysmmu_fimc0>;
+
+ samsung,pix-limits = <4224 8192 1920 4224>;
+ samsung,mainscaler-ext;
+ samsung,isp-wb;
+ samsung,cam-if;
+ };
+
+ /* ... FIMC 1-3 */
+
+ csis@11880000 {
+ compatible = "samsung,exynos4210-csis";
+ reg = <0x11880000 0x4000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clock CLK_CSIS0>,
+ <&clock CLK_SCLK_CSIS0>;
+ clock-names = "csis", "sclk_csis";
+ assigned-clocks = <&clock CLK_MOUT_CSIS0>,
+ <&clock CLK_SCLK_CSIS0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+
+ bus-width = <4>;
+ power-domains = <&pd_cam>;
+ phys = <&mipi_phy 0>;
+ phy-names = "csis";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+
+ /* Camera C (3) MIPI CSI-2 (CSIS0) */
+ port@3 {
+ reg = <3>;
+ endpoint {
+ remote-endpoint = <&s5c73m3_ep>;
+ data-lanes = <1 2 3 4>;
+ samsung,csis-hs-settle = <12>;
+ };
+ };
+ };
+
+ /* ... CSIS 1 */
+
+ fimc-lite@12390000 {
+ compatible = "samsung,exynos4212-fimc-lite";
+ reg = <0x12390000 0x1000>;
+ interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ power-domains = <&pd_isp>;
+ clocks = <&isp_clock CLK_ISP_FIMC_LITE0>;
+ clock-names = "flite";
+ iommus = <&sysmmu_fimc_lite0>;
+ };
+
+ /* ... FIMC-LITE 1 */
+
+ fimc-is@12000000 {
+ compatible = "samsung,exynos4212-fimc-is";
+ reg = <0x12000000 0x260000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&isp_clock CLK_ISP_FIMC_LITE0>,
+ <&isp_clock CLK_ISP_FIMC_LITE1>,
+ <&isp_clock CLK_ISP_PPMUISPX>,
+ <&isp_clock CLK_ISP_PPMUISPMX>,
+ <&isp_clock CLK_ISP_FIMC_ISP>,
+ <&isp_clock CLK_ISP_FIMC_DRC>,
+ <&isp_clock CLK_ISP_FIMC_FD>,
+ <&isp_clock CLK_ISP_MCUISP>,
+ <&isp_clock CLK_ISP_GICISP>,
+ <&isp_clock CLK_ISP_MCUCTL_ISP>,
+ <&isp_clock CLK_ISP_PWM_ISP>,
+ <&isp_clock CLK_ISP_DIV_ISP0>,
+ <&isp_clock CLK_ISP_DIV_ISP1>,
+ <&isp_clock CLK_ISP_DIV_MCUISP0>,
+ <&isp_clock CLK_ISP_DIV_MCUISP1>,
+ <&clock CLK_MOUT_MPLL_USER_T>,
+ <&clock CLK_ACLK200>,
+ <&clock CLK_ACLK400_MCUISP>,
+ <&clock CLK_DIV_ACLK200>,
+ <&clock CLK_DIV_ACLK400_MCUISP>,
+ <&clock CLK_UART_ISP_SCLK>;
+ clock-names = "lite0", "lite1", "ppmuispx",
+ "ppmuispmx", "isp",
+ "drc", "fd", "mcuisp",
+ "gicisp", "mcuctl_isp", "pwm_isp",
+ "ispdiv0", "ispdiv1", "mcuispdiv0",
+ "mcuispdiv1", "mpll", "aclk200",
+ "aclk400mcuisp", "div_aclk200",
+ "div_aclk400mcuisp", "uart";
+ iommus = <&sysmmu_fimc_isp>, <&sysmmu_fimc_drc>,
+ <&sysmmu_fimc_fd>, <&sysmmu_fimc_mcuctl>;
+ iommu-names = "isp", "drc", "fd", "mcuctl";
+ power-domains = <&pd_isp>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pmu@10020000 {
+ reg = <0x10020000 0x3000>;
+ };
+
+ i2c-isp@12140000 {
+ compatible = "samsung,exynos4212-i2c-isp";
+ reg = <0x12140000 0x100>;
+ clocks = <&isp_clock CLK_ISP_I2C1_ISP>;
+ clock-names = "i2c_isp";
+ pinctrl-0 = <&fimc_is_i2c1>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ image-sensor@10 {
+ compatible = "samsung,s5k6a3";
+ reg = <0x10>;
+ svdda-supply = <&cam_io_reg>;
+ svddio-supply = <&ldo19_reg>;
+ afvdd-supply = <&ldo19_reg>;
+ clock-frequency = <24000000>;
+ /* CAM_B_CLKOUT */
+ clocks = <&camera 1>;
+ clock-names = "extclk";
+ gpios = <&gpm1 6 GPIO_ACTIVE_LOW>;
+
+ port {
+ endpoint {
+ remote-endpoint = <&csis1_ep>;
+ data-lanes = <1>;
+ };
+ };
+ };
+ };
+ };
+ };
deleted file mode 100644
@@ -1,210 +0,0 @@
-Samsung S5P/Exynos SoC Camera Subsystem (FIMC)
-----------------------------------------------
-
-The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices
-represented by separate device tree nodes. Currently this includes: FIMC (in
-the S5P SoCs series known as CAMIF), MIPI CSIS, FIMC-LITE and FIMC-IS (ISP).
-
-The sub-subdevices are defined as child nodes of the common 'camera' node which
-also includes common properties of the whole subsystem not really specific to
-any single sub-device, like common camera port pins or the CAMCLK clock outputs
-for external image sensors attached to an SoC.
-
-Common 'camera' node
---------------------
-
-Required properties:
-
-- compatible: must be "samsung,fimc"
-- clocks: list of clock specifiers, corresponding to entries in
- the clock-names property;
-- clock-names : must contain "sclk_cam0", "sclk_cam1", "pxl_async0",
- "pxl_async1" entries, matching entries in the clocks property.
-
-- #clock-cells: from the common clock bindings (../clock/clock-bindings.txt),
- must be 1. A clock provider is associated with the 'camera' node and it should
- be referenced by external sensors that use clocks provided by the SoC on
- CAM_*_CLKOUT pins. The clock specifier cell stores an index of a clock.
- The indices are 0, 1 for CAM_A_CLKOUT, CAM_B_CLKOUT clocks respectively.
-
-- clock-output-names: from the common clock bindings, should contain names of
- clocks registered by the camera subsystem corresponding to CAM_A_CLKOUT,
- CAM_B_CLKOUT output clocks respectively.
-
-The pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt must be used
-to define a required pinctrl state named "default" and optional pinctrl states:
-"idle", "active-a", active-b". These optional states can be used to switch the
-camera port pinmux at runtime. The "idle" state should configure both the camera
-ports A and B into high impedance state, especially the CAMCLK clock output
-should be inactive. For the "active-a" state the camera port A must be activated
-and the port B deactivated and for the state "active-b" it should be the other
-way around.
-
-The 'camera' node must include at least one 'fimc' child node.
-
-
-'fimc' device nodes
--------------------
-
-Required properties:
-
-- compatible: "samsung,s5pv210-fimc" for S5PV210, "samsung,exynos4210-fimc"
- for Exynos4210 and "samsung,exynos4212-fimc" for Exynos4x12 SoCs;
-- reg: physical base address and length of the registers set for the device;
-- interrupts: should contain FIMC interrupt;
-- clocks: list of clock specifiers, must contain an entry for each required
- entry in clock-names;
-- clock-names: must contain "fimc", "sclk_fimc" entries.
-- samsung,pix-limits: an array of maximum supported image sizes in pixels, for
- details refer to Table 2-1 in the S5PV210 SoC User Manual; The meaning of
- each cell is as follows:
- 0 - scaler input horizontal size,
- 1 - input horizontal size for the scaler bypassed,
- 2 - REAL_WIDTH without input rotation,
- 3 - REAL_HEIGHT with input rotation,
-- samsung,sysreg: a phandle to the SYSREG node.
-
-Each FIMC device should have an alias in the aliases node, in the form of
-fimc<n>, where <n> is an integer specifying the IP block instance.
-
-Optional properties:
-
-- clock-frequency: maximum FIMC local clock (LCLK) frequency;
-- samsung,min-pix-sizes: an array specyfing minimum image size in pixels at
- the FIMC input and output DMA, in the first and second cell respectively.
- Default value when this property is not present is <16 16>;
-- samsung,min-pix-alignment: minimum supported image height alignment (first
- cell) and the horizontal image offset (second cell). The values are in pixels
- and default to <2 1> when this property is not present;
-- samsung,mainscaler-ext: a boolean property indicating whether the FIMC IP
- supports extended image size and has CIEXTEN register;
-- samsung,rotators: a bitmask specifying whether this IP has the input and
- the output rotator. Bits 4 and 0 correspond to input and output rotator
- respectively. If a rotator is present its corresponding bit should be set.
- Default value when this property is not specified is 0x11.
-- samsung,cam-if: a bolean property indicating whether the IP block includes
- the camera input interface.
-- samsung,isp-wb: this property must be present if the IP block has the ISP
- writeback input.
-- samsung,lcd-wb: this property must be present if the IP block has the LCD
- writeback input.
-
-
-'parallel-ports' node
----------------------
-
-This node should contain child 'port' nodes specifying active parallel video
-input ports. It includes camera A and camera B inputs. 'reg' property in the
-port nodes specifies data input - 1, 2 indicates input A, B respectively.
-
-Optional properties
-
-- samsung,camclk-out (deprecated) : specifies clock output for remote sensor,
- 0 - CAM_A_CLKOUT, 1 - CAM_B_CLKOUT;
-
-Image sensor nodes
-------------------
-
-The sensor device nodes should be added to their control bus controller (e.g.
-I2C0) nodes and linked to a port node in the csis or the parallel-ports node,
-using the common video interfaces bindings, defined in video-interfaces.txt.
-
-Example:
-
- aliases {
- fimc0 = &fimc_0;
- };
-
- /* Parallel bus IF sensor */
- i2c_0: i2c@13860000 {
- s5k6aa: sensor@3c {
- compatible = "samsung,s5k6aafx";
- reg = <0x3c>;
- vddio-supply = <...>;
-
- clock-frequency = <24000000>;
- clocks = <&camera 1>;
- clock-names = "mclk";
-
- port {
- s5k6aa_ep: endpoint {
- remote-endpoint = <&fimc0_ep>;
- bus-width = <8>;
- hsync-active = <0>;
- vsync-active = <1>;
- pclk-sample = <1>;
- };
- };
- };
-
- /* MIPI CSI-2 bus IF sensor */
- s5c73m3: sensor@1a {
- compatible = "samsung,s5c73m3";
- reg = <0x1a>;
- vddio-supply = <...>;
-
- clock-frequency = <24000000>;
- clocks = <&camera 0>;
- clock-names = "mclk";
-
- port {
- s5c73m3_1: endpoint {
- data-lanes = <1 2 3 4>;
- remote-endpoint = <&csis0_ep>;
- };
- };
- };
- };
-
- camera@11800000 {
- compatible = "samsung,fimc";
- clocks = <&clock 132>, <&clock 133>, <&clock 351>,
- <&clock 352>;
- clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0",
- "pxl_async1";
- #clock-cells = <1>;
- clock-output-names = "cam_a_clkout", "cam_b_clkout";
- pinctrl-names = "default";
- pinctrl-0 = <&cam_port_a_clk_active>;
- ranges;
- #address-cells = <1>;
- #size-cells = <1>;
-
- /* parallel camera ports */
- parallel-ports {
- /* camera A input */
- port@1 {
- reg = <1>;
- fimc0_ep: endpoint {
- remote-endpoint = <&s5k6aa_ep>;
- bus-width = <8>;
- hsync-active = <0>;
- vsync-active = <1>;
- pclk-sample = <1>;
- };
- };
- };
-
- fimc_0: fimc@11800000 {
- compatible = "samsung,exynos4210-fimc";
- reg = <0x11800000 0x1000>;
- interrupts = <0 85 0>;
- };
-
- csis_0: csis@11880000 {
- compatible = "samsung,exynos4210-csis";
- reg = <0x11880000 0x1000>;
- interrupts = <0 78 0>;
- /* camera C input */
- port@3 {
- reg = <3>;
- csis0_ep: endpoint {
- remote-endpoint = <&s5c73m3_ep>;
- data-lanes = <1 2 3 4>;
- samsung,csis-hs-settle = <12>;
- };
- };
- };
- };
-
-The MIPI-CSIS device binding is defined in samsung-mipi-csis.txt.
@@ -18557,8 +18557,10 @@ L: linux-media@vger.kernel.org
S: Supported
Q: https://patchwork.linuxtv.org/project/linux-media/list/
F: Documentation/devicetree/bindings/media/samsung,exynos4210-csis.yaml
+F: Documentation/devicetree/bindings/media/samsung,exynos4210-fimc.yaml
F: Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-is.yaml
F: Documentation/devicetree/bindings/media/samsung,exynos4212-fimc-lite.yaml
+F: Documentation/devicetree/bindings/media/samsung,fimc.yaml
F: drivers/media/platform/samsung/exynos4-is/
SAMSUNG SOC CLOCK DRIVERS