@@ -25,7 +25,6 @@
#include <linux/irq.h>
#include <linux/mutex.h>
#include <linux/slab.h>
-#include <linux/i2c/sx150x.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
@@ -85,6 +84,65 @@ struct sx150x_device_data {
} pri;
};
+/**
+ * struct sx150x_platform_data - config data for SX150x driver
+ * @gpio_base: The index number of the first GPIO assigned to this
+ * GPIO expander. The expander will create a block of
+ * consecutively numbered gpios beginning at the given base,
+ * with the size of the block depending on the model of the
+ * expander chip.
+ * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
+ * instead of as an oscillator, increasing the size of the
+ * GP(I)O pool created by this expander by one. The
+ * output-only GPO pin will be added at the end of the block.
+ * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
+ * for each IO line in the expander. Setting the bit at
+ * position n will enable the pull-up for the IO at
+ * the corresponding offset. For chips with fewer than
+ * 16 IO pins, high-end bits are ignored.
+ * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
+ * resistor for each IO line in the expander. Setting the
+ * bit at position n will enable the pull-down for the IO at
+ * the corresponding offset. For chips with fewer than
+ * 16 IO pins, high-end bits are ignored.
+ * @io_open_drain_ena: A bit-mask which enables-or disables open-drain
+ * operation for each IO line in the expander. Setting the
+ * bit at position n enables open-drain operation for
+ * the IO at the corresponding offset. Clearing the bit
+ * enables regular push-pull operation for that IO.
+ * For chips with fewer than 16 IO pins, high-end bits
+ * are ignored.
+ * @io_polarity: A bit-mask which enables polarity inversion for each IO line
+ * in the expander. Setting the bit at position n inverts
+ * the polarity of that IO line, while clearing it results
+ * in normal polarity. For chips with fewer than 16 IO pins,
+ * high-end bits are ignored.
+ * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
+ * is connected, via which it reports interrupt events
+ * across all GPIO lines. This must be a real,
+ * pre-existing IRQ line.
+ * Setting this value < 0 disables the irq_chip functionality
+ * of the driver.
+ * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
+ * IRQ lines will appear. Similarly to gpio_base, the expander
+ * will create a block of irqs beginning at this number.
+ * This value is ignored if irq_summary is < 0.
+ * @reset_during_probe: If set to true, the driver will trigger a full
+ * reset of the chip at the beginning of the probe
+ * in order to place it in a known state.
+ */
+struct sx150x_platform_data {
+ unsigned gpio_base;
+ bool oscio_is_gpo;
+ u16 io_pullup_ena;
+ u16 io_pulldn_ena;
+ u16 io_open_drain_ena;
+ u16 io_polarity;
+ int irq_summary;
+ unsigned irq_base;
+ bool reset_during_probe;
+};
+
struct sx150x_chip {
struct gpio_chip gpio_chip;
struct i2c_client *client;
deleted file mode 100644
@@ -1,82 +0,0 @@
-/*
- * Driver for the Semtech SX150x I2C GPIO Expanders
- *
- * Copyright (c) 2010, Code Aurora Forum. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
- */
-#ifndef __LINUX_I2C_SX150X_H
-#define __LINUX_I2C_SX150X_H
-
-/**
- * struct sx150x_platform_data - config data for SX150x driver
- * @gpio_base: The index number of the first GPIO assigned to this
- * GPIO expander. The expander will create a block of
- * consecutively numbered gpios beginning at the given base,
- * with the size of the block depending on the model of the
- * expander chip.
- * @oscio_is_gpo: If set to true, the driver will configure OSCIO as a GPO
- * instead of as an oscillator, increasing the size of the
- * GP(I)O pool created by this expander by one. The
- * output-only GPO pin will be added at the end of the block.
- * @io_pullup_ena: A bit-mask which enables or disables the pull-up resistor
- * for each IO line in the expander. Setting the bit at
- * position n will enable the pull-up for the IO at
- * the corresponding offset. For chips with fewer than
- * 16 IO pins, high-end bits are ignored.
- * @io_pulldn_ena: A bit-mask which enables-or disables the pull-down
- * resistor for each IO line in the expander. Setting the
- * bit at position n will enable the pull-down for the IO at
- * the corresponding offset. For chips with fewer than
- * 16 IO pins, high-end bits are ignored.
- * @io_open_drain_ena: A bit-mask which enables-or disables open-drain
- * operation for each IO line in the expander. Setting the
- * bit at position n enables open-drain operation for
- * the IO at the corresponding offset. Clearing the bit
- * enables regular push-pull operation for that IO.
- * For chips with fewer than 16 IO pins, high-end bits
- * are ignored.
- * @io_polarity: A bit-mask which enables polarity inversion for each IO line
- * in the expander. Setting the bit at position n inverts
- * the polarity of that IO line, while clearing it results
- * in normal polarity. For chips with fewer than 16 IO pins,
- * high-end bits are ignored.
- * @irq_summary: The 'summary IRQ' line to which the GPIO expander's INT line
- * is connected, via which it reports interrupt events
- * across all GPIO lines. This must be a real,
- * pre-existing IRQ line.
- * Setting this value < 0 disables the irq_chip functionality
- * of the driver.
- * @irq_base: The first 'virtual IRQ' line at which our block of GPIO-based
- * IRQ lines will appear. Similarly to gpio_base, the expander
- * will create a block of irqs beginning at this number.
- * This value is ignored if irq_summary is < 0.
- * @reset_during_probe: If set to true, the driver will trigger a full
- * reset of the chip at the beginning of the probe
- * in order to place it in a known state.
- */
-struct sx150x_platform_data {
- unsigned gpio_base;
- bool oscio_is_gpo;
- u16 io_pullup_ena;
- u16 io_pulldn_ena;
- u16 io_open_drain_ena;
- u16 io_polarity;
- int irq_summary;
- unsigned irq_base;
- bool reset_during_probe;
-};
-
-#endif /* __LINUX_I2C_SX150X_H */
The sx150x has some platform data definition in <linux/i2c/sx150x.h> but this file is only included from the driver in the whole kernel so move its contents into the driver. Cc: Wei Chen <Wei.Chen@csr.com> Cc: Peter Rosin <peda@axentia.se> Cc: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- Wolfram: I assume you're OK with me stealing this file. --- drivers/gpio/gpio-sx150x.c | 60 ++++++++++++++++++++++++++++++++- include/linux/i2c/sx150x.h | 82 ---------------------------------------------- 2 files changed, 59 insertions(+), 83 deletions(-) delete mode 100644 include/linux/i2c/sx150x.h -- 2.4.3 -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html