@@ -2695,7 +2695,7 @@ qup_i2c0_data_clk: qup-i2c0-data-clk-state {
pins = "gpio28", "gpio29";
function = "qup1_se0";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c1_data_clk: qup-i2c1-data-clk-state {
@@ -2703,7 +2703,7 @@ qup_i2c1_data_clk: qup-i2c1-data-clk-state {
pins = "gpio32", "gpio33";
function = "qup1_se1";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c2_data_clk: qup-i2c2-data-clk-state {
@@ -2711,7 +2711,7 @@ qup_i2c2_data_clk: qup-i2c2-data-clk-state {
pins = "gpio36", "gpio37";
function = "qup1_se2";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c3_data_clk: qup-i2c3-data-clk-state {
@@ -2719,7 +2719,7 @@ qup_i2c3_data_clk: qup-i2c3-data-clk-state {
pins = "gpio40", "gpio41";
function = "qup1_se3";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c4_data_clk: qup-i2c4-data-clk-state {
@@ -2727,7 +2727,7 @@ qup_i2c4_data_clk: qup-i2c4-data-clk-state {
pins = "gpio44", "gpio45";
function = "qup1_se4";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c5_data_clk: qup-i2c5-data-clk-state {
@@ -2735,7 +2735,7 @@ qup_i2c5_data_clk: qup-i2c5-data-clk-state {
pins = "gpio52", "gpio53";
function = "qup1_se5";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c6_data_clk: qup-i2c6-data-clk-state {
@@ -2743,7 +2743,7 @@ qup_i2c6_data_clk: qup-i2c6-data-clk-state {
pins = "gpio48", "gpio49";
function = "qup1_se6";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c8_data_clk: qup-i2c8-data-clk-state {
@@ -2751,14 +2751,14 @@ scl-pins {
pins = "gpio57";
function = "qup2_se0_l1_mira";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
sda-pins {
pins = "gpio56";
function = "qup2_se0_l0_mira";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
};
@@ -2767,7 +2767,7 @@ qup_i2c9_data_clk: qup-i2c9-data-clk-state {
pins = "gpio60", "gpio61";
function = "qup2_se1";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c10_data_clk: qup-i2c10-data-clk-state {
@@ -2775,7 +2775,7 @@ qup_i2c10_data_clk: qup-i2c10-data-clk-state {
pins = "gpio64", "gpio65";
function = "qup2_se2";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c11_data_clk: qup-i2c11-data-clk-state {
@@ -2783,7 +2783,7 @@ qup_i2c11_data_clk: qup-i2c11-data-clk-state {
pins = "gpio68", "gpio69";
function = "qup2_se3";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c12_data_clk: qup-i2c12-data-clk-state {
@@ -2791,7 +2791,7 @@ qup_i2c12_data_clk: qup-i2c12-data-clk-state {
pins = "gpio2", "gpio3";
function = "qup2_se4";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c13_data_clk: qup-i2c13-data-clk-state {
@@ -2799,7 +2799,7 @@ qup_i2c13_data_clk: qup-i2c13-data-clk-state {
pins = "gpio80", "gpio81";
function = "qup2_se5";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_i2c15_data_clk: qup-i2c15-data-clk-state {
@@ -2807,7 +2807,7 @@ qup_i2c15_data_clk: qup-i2c15-data-clk-state {
pins = "gpio72", "gpio106";
function = "qup2_se7";
drive-strength = <2>;
- bias-pull-up;
+ bias-pull-up = <2200>;
};
qup_spi0_cs: qup-spi0-cs-state {
The default bias pull up value for the tlmm i2c data clk states is 2.2kOhms. Add this value to make sure the driver factors in the i2c pull up bit when writing the config register. Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- The v3 of this specific patch is here: https://lore.kernel.org/all/20230208081836.984673-2-abel.vesa@linaro.org/ Changes since v3: * none arch/arm64/boot/dts/qcom/sm8550.dtsi | 30 ++++++++++++++-------------- 1 file changed, 15 insertions(+), 15 deletions(-)