| Message ID | 20230210114957.2667963-2-danishanwar@ti.com |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Introduce ICSSG based ethernet Driver | expand |
On Fri, 10 Feb 2023 17:19:56 +0530, MD Danish Anwar wrote: > From: Puranjay Mohan <p-mohan@ti.com> > > Add a YAML binding document for the ICSSG Programmable real time unit > based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer > APIs to interface the PRUs and load/run the firmware for supporting > ethernet functionality. > > Signed-off-by: Puranjay Mohan <p-mohan@ti.com> > Signed-off-by: Md Danish Anwar <danishanwar@ti.com> > --- > .../bindings/net/ti,icssg-prueth.yaml | 184 ++++++++++++++++++ > 1 file changed, 184 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: ./Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml: Unable to find schema file matching $id: http://devicetree.org/schemas/remoteproc/ti,pru-consumer.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.example.dtb: ethernet: False schema does not allow {'compatible': ['ti,am654-icssg-prueth'], 'pinctrl-names': ['default'], 'pinctrl-0': [[4294967295]], 'ti,sram': [[4294967295]], 'ti,prus': [[4294967295, 4294967295, 4294967295, 4294967295, 4294967295, 4294967295]], 'firmware-name': ['ti-pruss/am65x-pru0-prueth-fw.elf', 'ti-pruss/am65x-rtu0-prueth-fw.elf', 'ti-pruss/am65x-txpru0-prueth-fw.elf', 'ti-pruss/am65x-pru1-prueth-fw.elf', 'ti-pruss/am65x-rtu1-prueth-fw.elf', 'ti-pruss/am65x-txpru1-prueth-fw.elf'], 'ti,pruss-gp-mux-sel': [[2, 2, 2, 2, 2, 2]], 'dmas': [[4294967295, 49920], [4294967295, 49921], [4294967295, 49922], [4294967295, 49923], [4294967295, 49924], [4294967295, 49925], [4294967295, 49926], [4294967295, 49927], [4294967295, 17152], [4294967295, 17153]], 'dma-names': ['tx0-0', 'tx0-1', 'tx0-2', 'tx0-3', 'tx1-0', 'tx1-1', 'tx1-2', 'tx1-3', 'rx0', 'rx1'], 'ti,mii-g-rt': [[4294967295]] , 'interrupts': [[24, 0, 2], [25, 1, 3]], 'interrupt-names': ['tx_ts0', 'tx_ts1'], 'ethernet-ports': {'#address-cells': [[1]], '#size-cells': [[0]], 'port@0': {'reg': [[0]], 'phy-handle': [[4294967295]], 'phy-mode': ['rgmii-id'], 'interrupts-extended': [[4294967295, 24]], 'ti,syscon-rgmii-delay': [[4294967295, 16672]], 'local-mac-address': [[0, 0, 0, 0, 0, 0]]}, 'port@1': {'reg': [[1]], 'phy-handle': [[4294967295]], 'phy-mode': ['rgmii-id'], 'interrupts-extended': [[4294967295, 25]], 'ti,syscon-rgmii-delay': [[4294967295, 16676]], 'local-mac-address': [[0, 0, 0, 0, 0, 0]]}}, '$nodename': ['ethernet']} From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.example.dtb: ethernet: Unevaluated properties are not allowed ('firmware-name', 'ti,prus', 'ti,pruss-gp-mux-sel' were unexpected) From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230210114957.2667963-2-danishanwar@ti.com The base for the series is generally the latest rc1. A different dependency should be noted in *this* patch. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit after running the above command yourself. Note that DT_SCHEMA_FILES can be set to your schema file to speed up checking your schema. However, it must be unset to test all examples with your schema.
On 10/02/23 19:28, Rob Herring wrote: > > On Fri, 10 Feb 2023 17:19:56 +0530, MD Danish Anwar wrote: >> From: Puranjay Mohan <p-mohan@ti.com> >> >> Add a YAML binding document for the ICSSG Programmable real time unit >> based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer >> APIs to interface the PRUs and load/run the firmware for supporting >> ethernet functionality. >> >> Signed-off-by: Puranjay Mohan <p-mohan@ti.com> >> Signed-off-by: Md Danish Anwar <danishanwar@ti.com> >> --- >> .../bindings/net/ti,icssg-prueth.yaml | 184 ++++++++++++++++++ >> 1 file changed, 184 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml >> > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > yamllint warnings/errors: > > dtschema/dtc warnings/errors: > ./Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml: Unable to find schema file matching $id: http://devicetree.org/schemas/remoteproc/ti,pru-consumer.yaml > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.example.dtb: ethernet: False schema does not allow {'compatible': ['ti,am654-icssg-prueth'], 'pinctrl-names': ['default'], 'pinctrl-0': [[4294967295]], 'ti,sram': [[4294967295]], 'ti,prus': [[4294967295, 4294967295, 4294967295, 4294967295, 4294967295, 4294967295]], 'firmware-name': ['ti-pruss/am65x-pru0-prueth-fw.elf', 'ti-pruss/am65x-rtu0-prueth-fw.elf', 'ti-pruss/am65x-txpru0-prueth-fw.elf', 'ti-pruss/am65x-pru1-prueth-fw.elf', 'ti-pruss/am65x-rtu1-prueth-fw.elf', 'ti-pruss/am65x-txpru1-prueth-fw.elf'], 'ti,pruss-gp-mux-sel': [[2, 2, 2, 2, 2, 2]], 'dmas': [[4294967295, 49920], [4294967295, 49921], [4294967295, 49922], [4294967295, 49923], [4294967295, 49924], [4294967295, 49925], [4294967295, 49926], [4294967295, 49927], [4294967295, 17152], [4294967295, 17153]], 'dma-names': ['tx0-0', 'tx0-1', 'tx0-2', 'tx0-3', 'tx1-0', 'tx1-1', 'tx1-2', 'tx1-3', 'rx0', 'rx1'], 'ti,mii-g-rt': [[429! > 4967295]], 'interrupts': [[24, 0, 2], [25, 1, 3]], 'interrupt-names': ['tx_ts0', 'tx_ts1'], 'ethernet-ports': {'#address-cells': [[1]], '#size-cells': [[0]], 'port@0': {'reg': [[0]], 'phy-handle': [[4294967295]], 'phy-mode': ['rgmii-id'], 'interrupts-extended': [[4294967295, 24]], 'ti,syscon-rgmii-delay': [[4294967295, 16672]], 'local-mac-address': [[0, 0, 0, 0, 0, 0]]}, 'port@1': {'reg': [[1]], 'phy-handle': [[4294967295]], 'phy-mode': ['rgmii-id'], 'interrupts-extended': [[4294967295, 25]], 'ti,syscon-rgmii-delay': [[4294967295, 16676]], 'local-mac-address': [[0, 0, 0, 0, 0, 0]]}}, '$nodename': ['ethernet']} > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.example.dtb: ethernet: Unevaluated properties are not allowed ('firmware-name', 'ti,prus', 'ti,pruss-gp-mux-sel' were unexpected) > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > > doc reference errors (make refcheckdocs): > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230210114957.2667963-2-danishanwar@ti.com Hi Rob, This patch depends on the patch [1] which is posted through series [2]. Patch [1] is currently approved, reviewed and will soon be merged to mainline Linux. Once it is merged this patch won't throw the above error. In the meantime I have posted this patch to get it reviewed so that once patch [1] gets merged, this will be ready to be merged. [1] https://lore.kernel.org/all/20230106121046.886863-2-danishanwar@ti.com/ [2] https://lore.kernel.org/all/20230106121046.886863-1-danishanwar@ti.com/ > > The base for the series is generally the latest rc1. A different dependency > should be noted in *this* patch. > > If you already ran 'make dt_binding_check' and didn't see the above > error(s), then make sure 'yamllint' is installed and dt-schema is up to > date: > > pip3 install dtschema --upgrade > > Please check and re-submit after running the above command yourself. Note > that DT_SCHEMA_FILES can be set to your schema file to speed up checking > your schema. However, it must be unset to test all examples with your schema. >
On Fri, Feb 10, 2023 at 09:00:59PM +0530, Md Danish Anwar wrote: > > > On 10/02/23 19:28, Rob Herring wrote: > > > > On Fri, 10 Feb 2023 17:19:56 +0530, MD Danish Anwar wrote: > >> From: Puranjay Mohan <p-mohan@ti.com> > >> > >> Add a YAML binding document for the ICSSG Programmable real time unit > >> based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer > >> APIs to interface the PRUs and load/run the firmware for supporting > >> ethernet functionality. > >> > >> Signed-off-by: Puranjay Mohan <p-mohan@ti.com> > >> Signed-off-by: Md Danish Anwar <danishanwar@ti.com> > >> --- > >> .../bindings/net/ti,icssg-prueth.yaml | 184 ++++++++++++++++++ > >> 1 file changed, 184 insertions(+) > >> create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > >> > > > > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' > > on your patch (DT_CHECKER_FLAGS is new in v5.13): > > > > yamllint warnings/errors: > > > > dtschema/dtc warnings/errors: > > ./Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml: Unable to find schema file matching $id: http://devicetree.org/schemas/remoteproc/ti,pru-consumer.yaml > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.example.dtb: ethernet: False schema does not allow {'compatible': ['ti,am654-icssg-prueth'], 'pinctrl-names': ['default'], 'pinctrl-0': [[4294967295]], 'ti,sram': [[4294967295]], 'ti,prus': [[4294967295, 4294967295, 4294967295, 4294967295, 4294967295, 4294967295]], 'firmware-name': ['ti-pruss/am65x-pru0-prueth-fw.elf', 'ti-pruss/am65x-rtu0-prueth-fw.elf', 'ti-pruss/am65x-txpru0-prueth-fw.elf', 'ti-pruss/am65x-pru1-prueth-fw.elf', 'ti-pruss/am65x-rtu1-prueth-fw.elf', 'ti-pruss/am65x-txpru1-prueth-fw.elf'], 'ti,pruss-gp-mux-sel': [[2, 2, 2, 2, 2, 2]], 'dmas': [[4294967295, 49920], [4294967295, 49921], [4294967295, 49922], [4294967295, 49923], [4294967295, 49924], [4294967295, 49925], [4294967295, 49926], [4294967295, 49927], [4294967295, 17152], [4294967295, 17153]], 'dma-names': ['tx0-0', 'tx0-1', 'tx0-2', 'tx0-3', 'tx1-0', 'tx1-1', 'tx1-2', 'tx1-3', 'rx0', 'rx1'], 'ti,mii-g-rt': [[429! > > 4967295]], 'interrupts': [[24, 0, 2], [25, 1, 3]], 'interrupt-names': ['tx_ts0', 'tx_ts1'], 'ethernet-ports': {'#address-cells': [[1]], '#size-cells': [[0]], 'port@0': {'reg': [[0]], 'phy-handle': [[4294967295]], 'phy-mode': ['rgmii-id'], 'interrupts-extended': [[4294967295, 24]], 'ti,syscon-rgmii-delay': [[4294967295, 16672]], 'local-mac-address': [[0, 0, 0, 0, 0, 0]]}, 'port@1': {'reg': [[1]], 'phy-handle': [[4294967295]], 'phy-mode': ['rgmii-id'], 'interrupts-extended': [[4294967295, 25]], 'ti,syscon-rgmii-delay': [[4294967295, 16676]], 'local-mac-address': [[0, 0, 0, 0, 0, 0]]}}, '$nodename': ['ethernet']} > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > > /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.example.dtb: ethernet: Unevaluated properties are not allowed ('firmware-name', 'ti,prus', 'ti,pruss-gp-mux-sel' were unexpected) > > From schema: /builds/robherring/dt-review-ci/linux/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > > > > doc reference errors (make refcheckdocs): > > > > See https://patchwork.ozlabs.org/project/devicetree-bindings/patch/20230210114957.2667963-2-danishanwar@ti.com > > Hi Rob, > This patch depends on the patch [1] which is posted through series [2]. Patch > [1] is currently approved, reviewed and will soon be merged to mainline Linux. > Once it is merged this patch won't throw the above error. > > In the meantime I have posted this patch to get it reviewed so that once patch > [1] gets merged, this will be ready to be merged. > > [1] https://lore.kernel.org/all/20230106121046.886863-2-danishanwar@ti.com/ > [2] https://lore.kernel.org/all/20230106121046.886863-1-danishanwar@ti.com/ State that in *this* patch if you don't want to get the report. Rob
On Fri, Feb 10, 2023 at 05:19:56PM +0530, MD Danish Anwar wrote: > From: Puranjay Mohan <p-mohan@ti.com> > > Add a YAML binding document for the ICSSG Programmable real time unit > based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer > APIs to interface the PRUs and load/run the firmware for supporting > ethernet functionality. > > Signed-off-by: Puranjay Mohan <p-mohan@ti.com> > Signed-off-by: Md Danish Anwar <danishanwar@ti.com> > --- > .../bindings/net/ti,icssg-prueth.yaml | 184 ++++++++++++++++++ > 1 file changed, 184 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > > diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > new file mode 100644 > index 000000000000..8b860f29ecc0 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml > @@ -0,0 +1,184 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Texas Instruments ICSSG PRUSS Ethernet > + > +maintainers: > + - Md Danish Anwar <danishanwar@ti.com> > + > +description: > + Ethernet based on the Programmable Real-Time > + Unit and Industrial Communication Subsystem. Odd line wrap length. It should be 80 chars. > + > +allOf: > + - $ref: /schemas/remoteproc/ti,pru-consumer.yaml# > + > +properties: > + compatible: > + enum: > + - ti,am654-icssg-prueth # for AM65x SoC family > + > + ti,sram: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: > + phandle to MSMC SRAM node I believe we have a standard 'sram' property to point to SRAM nodes assuming this is just mmio-sram or similar. > + > + dmas: > + maxItems: 10 > + > + dma-names: > + items: > + - const: tx0-0 > + - const: tx0-1 > + - const: tx0-2 > + - const: tx0-3 > + - const: tx1-0 > + - const: tx1-1 > + - const: tx1-2 > + - const: tx1-3 > + - const: rx0 > + - const: rx1 > + > + ti,mii-g-rt: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: | > + phandle to MII_G_RT module's syscon regmap. > + > + ti,mii-rt: > + $ref: /schemas/types.yaml#/definitions/phandle > + description: | > + phandle to MII_RT module's syscon regmap > + > + interrupts: > + maxItems: 2 > + description: | Don't need '|' > + Interrupt specifiers to TX timestamp IRQ. > + > + interrupt-names: > + items: > + - const: tx_ts0 > + - const: tx_ts1 > + > + ethernet-ports: > + type: object > + additionalProperties: false > + > + properties: > + '#address-cells': > + const: 1 > + '#size-cells': > + const: 0 > + > + patternProperties: > + ^port@[0-1]$: > + type: object > + description: ICSSG PRUETH external ports > + $ref: ethernet-controller.yaml# > + unevaluatedProperties: false > + > + properties: > + reg: > + items: > + - enum: [0, 1] > + description: ICSSG PRUETH port number > + > + interrupts: > + maxItems: 1 > + > + ti,syscon-rgmii-delay: > + items: > + - items: > + - description: phandle to system controller node > + - description: The offset to ICSSG control register > + $ref: /schemas/types.yaml#/definitions/phandle-array > + description: > + phandle to system controller node and register offset > + to ICSSG control register for RGMII transmit delay > + > + required: > + - reg > + anyOf: > + - required: > + - port@0 > + - required: > + - port@1 > + > +required: > + - compatible > + - ti,sram > + - dmas > + - dma-names > + - ethernet-ports > + - ti,mii-g-rt > + - interrupts > + - interrupt-names > + > +unevaluatedProperties: false > + > +examples: > + - | > + /* Example k3-am654 base board SR2.0, dual-emac */ > + pruss2_eth: ethernet { > + compatible = "ti,am654-icssg-prueth"; > + pinctrl-names = "default"; > + pinctrl-0 = <&icssg2_rgmii_pins_default>; > + ti,sram = <&msmc_ram>; > + > + ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>, > + <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>; > + firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf", > + "ti-pruss/am65x-rtu0-prueth-fw.elf", > + "ti-pruss/am65x-txpru0-prueth-fw.elf", > + "ti-pruss/am65x-pru1-prueth-fw.elf", > + "ti-pruss/am65x-rtu1-prueth-fw.elf", > + "ti-pruss/am65x-txpru1-prueth-fw.elf"; > + ti,pruss-gp-mux-sel = <2>, /* MII mode */ > + <2>, > + <2>, > + <2>, /* MII mode */ > + <2>, > + <2>; > + dmas = <&main_udmap 0xc300>, /* egress slice 0 */ > + <&main_udmap 0xc301>, /* egress slice 0 */ > + <&main_udmap 0xc302>, /* egress slice 0 */ > + <&main_udmap 0xc303>, /* egress slice 0 */ > + <&main_udmap 0xc304>, /* egress slice 1 */ > + <&main_udmap 0xc305>, /* egress slice 1 */ > + <&main_udmap 0xc306>, /* egress slice 1 */ > + <&main_udmap 0xc307>, /* egress slice 1 */ > + <&main_udmap 0x4300>, /* ingress slice 0 */ > + <&main_udmap 0x4301>; /* ingress slice 1 */ > + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3", > + "tx1-0", "tx1-1", "tx1-2", "tx1-3", > + "rx0", "rx1"; > + ti,mii-g-rt = <&icssg2_mii_g_rt>; > + interrupt-parent = <&icssg2_intc>; > + interrupts = <24 0 2>, <25 1 3>; > + interrupt-names = "tx_ts0", "tx_ts1"; > + ethernet-ports { > + #address-cells = <1>; > + #size-cells = <0>; > + pruss2_emac0: port@0 { > + reg = <0>; > + phy-handle = <&pruss2_eth0_phy>; > + phy-mode = "rgmii-id"; > + interrupts-extended = <&icssg2_intc 24>; > + ti,syscon-rgmii-delay = <&scm_conf 0x4120>; > + /* Filled in by bootloader */ > + local-mac-address = [00 00 00 00 00 00]; > + }; > + > + pruss2_emac1: port@1 { > + reg = <1>; > + phy-handle = <&pruss2_eth1_phy>; > + phy-mode = "rgmii-id"; > + interrupts-extended = <&icssg2_intc 25>; > + ti,syscon-rgmii-delay = <&scm_conf 0x4124>; > + /* Filled in by bootloader */ > + local-mac-address = [00 00 00 00 00 00]; > + }; > + }; > + }; > -- > 2.25.1 >
Hi Rob, On 11/02/23 00:50, Rob Herring wrote: > On Fri, Feb 10, 2023 at 05:19:56PM +0530, MD Danish Anwar wrote: >> From: Puranjay Mohan <p-mohan@ti.com> >> >> Add a YAML binding document for the ICSSG Programmable real time unit >> based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer >> APIs to interface the PRUs and load/run the firmware for supporting >> ethernet functionality. >> >> Signed-off-by: Puranjay Mohan <p-mohan@ti.com> >> Signed-off-by: Md Danish Anwar <danishanwar@ti.com> >> --- >> .../bindings/net/ti,icssg-prueth.yaml | 184 ++++++++++++++++++ >> 1 file changed, 184 insertions(+) >> create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml >> >> diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml >> new file mode 100644 >> index 000000000000..8b860f29ecc0 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml >> @@ -0,0 +1,184 @@ >> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) >> +%YAML 1.2 >> +--- >> +$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml# >> +$schema: http://devicetree.org/meta-schemas/core.yaml# >> + >> +title: Texas Instruments ICSSG PRUSS Ethernet >> + >> +maintainers: >> + - Md Danish Anwar <danishanwar@ti.com> >> + >> +description: >> + Ethernet based on the Programmable Real-Time >> + Unit and Industrial Communication Subsystem. > > Odd line wrap length. It should be 80 chars. > Sure, I will modify it. >> + >> +allOf: >> + - $ref: /schemas/remoteproc/ti,pru-consumer.yaml# >> + >> +properties: >> + compatible: >> + enum: >> + - ti,am654-icssg-prueth # for AM65x SoC family >> + >> + ti,sram: >> + $ref: /schemas/types.yaml#/definitions/phandle >> + description: >> + phandle to MSMC SRAM node > > I believe we have a standard 'sram' property to point to SRAM nodes > assuming this is just mmio-sram or similar. > Yes, we have standard 'sram' property but Krzysztof had asked me to make the sram property vendor specific in last revision of this series. >> + >> + dmas: >> + maxItems: 10 >> + >> + dma-names: >> + items: >> + - const: tx0-0 >> + - const: tx0-1 >> + - const: tx0-2 >> + - const: tx0-3 >> + - const: tx1-0 >> + - const: tx1-1 >> + - const: tx1-2 >> + - const: tx1-3 >> + - const: rx0 >> + - const: rx1 >> + >> + ti,mii-g-rt: >> + $ref: /schemas/types.yaml#/definitions/phandle >> + description: | >> + phandle to MII_G_RT module's syscon regmap. >> + >> + ti,mii-rt: >> + $ref: /schemas/types.yaml#/definitions/phandle >> + description: | >> + phandle to MII_RT module's syscon regmap >> + >> + interrupts: >> + maxItems: 2 >> + description: | > > Don't need '|' > Sure, I will drop this. >> + Interrupt specifiers to TX timestamp IRQ. >> + >> + interrupt-names: >> + items: >> + - const: tx_ts0 >> + - const: tx_ts1 >> + >> + ethernet-ports: >> + type: object >> + additionalProperties: false >> + >> + properties: >> + '#address-cells': >> + const: 1 >> + '#size-cells': >> + const: 0 >> + >> + patternProperties: >> + ^port@[0-1]$: >> + type: object >> + description: ICSSG PRUETH external ports >> + $ref: ethernet-controller.yaml# >> + unevaluatedProperties: false >> + >> + properties: >> + reg: >> + items: >> + - enum: [0, 1] >> + description: ICSSG PRUETH port number >> + >> + interrupts: >> + maxItems: 1 >> + >> + ti,syscon-rgmii-delay: >> + items: >> + - items: >> + - description: phandle to system controller node >> + - description: The offset to ICSSG control register >> + $ref: /schemas/types.yaml#/definitions/phandle-array >> + description: >> + phandle to system controller node and register offset >> + to ICSSG control register for RGMII transmit delay >> + >> + required: >> + - reg >> + anyOf: >> + - required: >> + - port@0 >> + - required: >> + - port@1 >> + >> +required: >> + - compatible >> + - ti,sram >> + - dmas >> + - dma-names >> + - ethernet-ports >> + - ti,mii-g-rt >> + - interrupts >> + - interrupt-names >> + >> +unevaluatedProperties: false >> + >> +examples: >> + - | >> + /* Example k3-am654 base board SR2.0, dual-emac */ >> + pruss2_eth: ethernet { >> + compatible = "ti,am654-icssg-prueth"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&icssg2_rgmii_pins_default>; >> + ti,sram = <&msmc_ram>; >> + >> + ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>, >> + <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>; >> + firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf", >> + "ti-pruss/am65x-rtu0-prueth-fw.elf", >> + "ti-pruss/am65x-txpru0-prueth-fw.elf", >> + "ti-pruss/am65x-pru1-prueth-fw.elf", >> + "ti-pruss/am65x-rtu1-prueth-fw.elf", >> + "ti-pruss/am65x-txpru1-prueth-fw.elf"; >> + ti,pruss-gp-mux-sel = <2>, /* MII mode */ >> + <2>, >> + <2>, >> + <2>, /* MII mode */ >> + <2>, >> + <2>; >> + dmas = <&main_udmap 0xc300>, /* egress slice 0 */ >> + <&main_udmap 0xc301>, /* egress slice 0 */ >> + <&main_udmap 0xc302>, /* egress slice 0 */ >> + <&main_udmap 0xc303>, /* egress slice 0 */ >> + <&main_udmap 0xc304>, /* egress slice 1 */ >> + <&main_udmap 0xc305>, /* egress slice 1 */ >> + <&main_udmap 0xc306>, /* egress slice 1 */ >> + <&main_udmap 0xc307>, /* egress slice 1 */ >> + <&main_udmap 0x4300>, /* ingress slice 0 */ >> + <&main_udmap 0x4301>; /* ingress slice 1 */ >> + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3", >> + "tx1-0", "tx1-1", "tx1-2", "tx1-3", >> + "rx0", "rx1"; >> + ti,mii-g-rt = <&icssg2_mii_g_rt>; >> + interrupt-parent = <&icssg2_intc>; >> + interrupts = <24 0 2>, <25 1 3>; >> + interrupt-names = "tx_ts0", "tx_ts1"; >> + ethernet-ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + pruss2_emac0: port@0 { >> + reg = <0>; >> + phy-handle = <&pruss2_eth0_phy>; >> + phy-mode = "rgmii-id"; >> + interrupts-extended = <&icssg2_intc 24>; >> + ti,syscon-rgmii-delay = <&scm_conf 0x4120>; >> + /* Filled in by bootloader */ >> + local-mac-address = [00 00 00 00 00 00]; >> + }; >> + >> + pruss2_emac1: port@1 { >> + reg = <1>; >> + phy-handle = <&pruss2_eth1_phy>; >> + phy-mode = "rgmii-id"; >> + interrupts-extended = <&icssg2_intc 25>; >> + ti,syscon-rgmii-delay = <&scm_conf 0x4124>; >> + /* Filled in by bootloader */ >> + local-mac-address = [00 00 00 00 00 00]; >> + }; >> + }; >> + }; >> -- >> 2.25.1 >>
On 07/03/2023 05:57, Md Danish Anwar wrote: >>> +allOf: >>> + - $ref: /schemas/remoteproc/ti,pru-consumer.yaml# >>> + >>> +properties: >>> + compatible: >>> + enum: >>> + - ti,am654-icssg-prueth # for AM65x SoC family >>> + >>> + ti,sram: >>> + $ref: /schemas/types.yaml#/definitions/phandle >>> + description: >>> + phandle to MSMC SRAM node >> >> I believe we have a standard 'sram' property to point to SRAM nodes >> assuming this is just mmio-sram or similar. >> > > Yes, we have standard 'sram' property but Krzysztof had asked me to make the > sram property vendor specific in last revision of this series. Sorry about that. I missed that we already have a 'sram'. The question remains whether this is a phandle to MMIO SRAM or similar (sram.yaml). Best regards, Krzysztof
diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml new file mode 100644 index 000000000000..8b860f29ecc0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml @@ -0,0 +1,184 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments ICSSG PRUSS Ethernet + +maintainers: + - Md Danish Anwar <danishanwar@ti.com> + +description: + Ethernet based on the Programmable Real-Time + Unit and Industrial Communication Subsystem. + +allOf: + - $ref: /schemas/remoteproc/ti,pru-consumer.yaml# + +properties: + compatible: + enum: + - ti,am654-icssg-prueth # for AM65x SoC family + + ti,sram: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle to MSMC SRAM node + + dmas: + maxItems: 10 + + dma-names: + items: + - const: tx0-0 + - const: tx0-1 + - const: tx0-2 + - const: tx0-3 + - const: tx1-0 + - const: tx1-1 + - const: tx1-2 + - const: tx1-3 + - const: rx0 + - const: rx1 + + ti,mii-g-rt: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + phandle to MII_G_RT module's syscon regmap. + + ti,mii-rt: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + phandle to MII_RT module's syscon regmap + + interrupts: + maxItems: 2 + description: | + Interrupt specifiers to TX timestamp IRQ. + + interrupt-names: + items: + - const: tx_ts0 + - const: tx_ts1 + + ethernet-ports: + type: object + additionalProperties: false + + properties: + '#address-cells': + const: 1 + '#size-cells': + const: 0 + + patternProperties: + ^port@[0-1]$: + type: object + description: ICSSG PRUETH external ports + $ref: ethernet-controller.yaml# + unevaluatedProperties: false + + properties: + reg: + items: + - enum: [0, 1] + description: ICSSG PRUETH port number + + interrupts: + maxItems: 1 + + ti,syscon-rgmii-delay: + items: + - items: + - description: phandle to system controller node + - description: The offset to ICSSG control register + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + phandle to system controller node and register offset + to ICSSG control register for RGMII transmit delay + + required: + - reg + anyOf: + - required: + - port@0 + - required: + - port@1 + +required: + - compatible + - ti,sram + - dmas + - dma-names + - ethernet-ports + - ti,mii-g-rt + - interrupts + - interrupt-names + +unevaluatedProperties: false + +examples: + - | + /* Example k3-am654 base board SR2.0, dual-emac */ + pruss2_eth: ethernet { + compatible = "ti,am654-icssg-prueth"; + pinctrl-names = "default"; + pinctrl-0 = <&icssg2_rgmii_pins_default>; + ti,sram = <&msmc_ram>; + + ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>, + <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>; + firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf", + "ti-pruss/am65x-rtu0-prueth-fw.elf", + "ti-pruss/am65x-txpru0-prueth-fw.elf", + "ti-pruss/am65x-pru1-prueth-fw.elf", + "ti-pruss/am65x-rtu1-prueth-fw.elf", + "ti-pruss/am65x-txpru1-prueth-fw.elf"; + ti,pruss-gp-mux-sel = <2>, /* MII mode */ + <2>, + <2>, + <2>, /* MII mode */ + <2>, + <2>; + dmas = <&main_udmap 0xc300>, /* egress slice 0 */ + <&main_udmap 0xc301>, /* egress slice 0 */ + <&main_udmap 0xc302>, /* egress slice 0 */ + <&main_udmap 0xc303>, /* egress slice 0 */ + <&main_udmap 0xc304>, /* egress slice 1 */ + <&main_udmap 0xc305>, /* egress slice 1 */ + <&main_udmap 0xc306>, /* egress slice 1 */ + <&main_udmap 0xc307>, /* egress slice 1 */ + <&main_udmap 0x4300>, /* ingress slice 0 */ + <&main_udmap 0x4301>; /* ingress slice 1 */ + dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3", + "tx1-0", "tx1-1", "tx1-2", "tx1-3", + "rx0", "rx1"; + ti,mii-g-rt = <&icssg2_mii_g_rt>; + interrupt-parent = <&icssg2_intc>; + interrupts = <24 0 2>, <25 1 3>; + interrupt-names = "tx_ts0", "tx_ts1"; + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + pruss2_emac0: port@0 { + reg = <0>; + phy-handle = <&pruss2_eth0_phy>; + phy-mode = "rgmii-id"; + interrupts-extended = <&icssg2_intc 24>; + ti,syscon-rgmii-delay = <&scm_conf 0x4120>; + /* Filled in by bootloader */ + local-mac-address = [00 00 00 00 00 00]; + }; + + pruss2_emac1: port@1 { + reg = <1>; + phy-handle = <&pruss2_eth1_phy>; + phy-mode = "rgmii-id"; + interrupts-extended = <&icssg2_intc 25>; + ti,syscon-rgmii-delay = <&scm_conf 0x4124>; + /* Filled in by bootloader */ + local-mac-address = [00 00 00 00 00 00]; + }; + }; + };