@@ -6,6 +6,14 @@
*/
#include <common.h>
#include <phy.h>
+#include <linux/compat.h>
+#include <malloc.h>
+
+#include <fdtdec.h>
+#include <dm.h>
+#include <dt-bindings/net/ti-dp83867.h>
+
+DECLARE_GLOBAL_DATA_PTR;
/* TI DP83867 */
#define DP83867_DEVADDR 0x1f
@@ -57,6 +65,17 @@
#define MII_MMD_CTRL_INCR_RDWT 0x8000 /* post increment on reads & writes */
#define MII_MMD_CTRL_INCR_ON_WT 0xC000 /* post increment on writes only */
+/* User setting - can be taken from DTS */
+#define DEFAULT_RX_ID_DELAY DP83867_RGMIIDCTL_2_25_NS
+#define DEFAULT_TX_ID_DELAY DP83867_RGMIIDCTL_2_75_NS
+#define DEFAULT_FIFO_DEPTH DP83867_PHYCR_FIFO_DEPTH_4_B_NIB
+
+struct dp83867_private {
+ int rx_id_delay;
+ int tx_id_delay;
+ int fifo_depth;
+};
+
/**
* phy_read_mmd_indirect - reads data from the MMD registers
* @phydev: The PHY device bus
@@ -134,16 +153,58 @@ static inline bool phy_interface_is_rgmii(struct phy_device *phydev)
phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID;
}
-/* User setting - can be taken from DTS */
-#define RX_ID_DELAY 8
-#define TX_ID_DELAY 0xa
-#define FIFO_DEPTH 1
+#if defined(CONFIG_DM_ETH)
+/**
+ * dp83867_data_init - Convenience function for setting PHY specific data
+ *
+ * @phydev: the phy_device struct
+ */
+static int dp83867_of_init(struct phy_device *phydev)
+{
+ struct dp83867_private *dp83867 = phydev->priv;
+ struct udevice *dev = phydev->dev;
+
+ dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+ "ti,rx_int_delay", DEFAULT_RX_ID_DELAY);
+
+ dp83867->tx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+ "ti,tx_int_delay", DEFAULT_TX_ID_DELAY);
+
+ dp83867->fifo_depth = fdtdec_get_uint(gd->fdt_blob, dev->of_offset,
+ "ti,fifo_depth", DEFAULT_FIFO_DEPTH);
+
+ return 0;
+}
+#else
+static int dp83867_of_init(struct phy_device *phydev)
+{
+ dp83867->rx_id_delay = DEFAULT_RX_ID_DELAY;
+ dp83867->tx_id_delay = DEFAULT_TX_ID_DELAY;
+ dp83867->fifo_depth = DEFAULT_FIFO_DEPTH;
+
+ return 0;
+}
+#endif
static int dp83867_config(struct phy_device *phydev)
{
+ struct dp83867_private *dp83867;
unsigned int val, delay;
int ret;
+ if (!phydev->priv) {
+ dp83867 = kzalloc(sizeof(*dp83867), GFP_KERNEL);
+ if (!dp83867)
+ return -ENOMEM;
+
+ phydev->priv = dp83867;
+ ret = dp83867_of_init(phydev);
+ if (ret)
+ goto err_out;
+ } else {
+ dp83867 = (struct dp83867_private *)phydev->priv;
+ }
+
/* Restart the PHY. */
val = phy_read(phydev, MDIO_DEVAD_NONE, DP83867_CTRL);
phy_write(phydev, MDIO_DEVAD_NONE, DP83867_CTRL,
@@ -152,9 +213,9 @@ static int dp83867_config(struct phy_device *phydev)
if (phy_interface_is_rgmii(phydev)) {
ret = phy_write(phydev, MDIO_DEVAD_NONE, MII_DP83867_PHYCTRL,
(DP83867_MDI_CROSSOVER_AUTO << DP83867_MDI_CROSSOVER) |
- (FIFO_DEPTH << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
+ (dp83867->fifo_depth << DP83867_PHYCR_FIFO_DEPTH_SHIFT));
if (ret)
- return ret;
+ goto err_out;
}
if ((phydev->interface >= PHY_INTERFACE_MODE_RGMII_ID) &&
@@ -175,8 +236,8 @@ static int dp83867_config(struct phy_device *phydev)
phy_write_mmd_indirect(phydev, DP83867_RGMIICTL,
DP83867_DEVADDR, phydev->addr, val);
- delay = (RX_ID_DELAY |
- (TX_ID_DELAY << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
+ delay = (dp83867->rx_id_delay |
+ (dp83867->tx_id_delay << DP83867_RGMII_TX_CLK_DELAY_SHIFT));
phy_write_mmd_indirect(phydev, DP83867_RGMIIDCTL,
DP83867_DEVADDR, phydev->addr, delay);
@@ -184,6 +245,10 @@ static int dp83867_config(struct phy_device *phydev)
genphy_config_aneg(phydev);
return 0;
+
+err_out:
+ kfree(dp83867);
+ return ret;
}
static struct phy_driver DP83867_driver = {
Not all devices use the same internal delay or fifo depth. Add the ability to set the internal delay for rx or tx and the fifo depth via the devicetree. If the value is not set in the devicetree then set the delay to the default. If devicetree is not used then use the default defines within the driver. Signed-off-by: Dan Murphy <dmurphy@ti.com> --- v2 - no change from v1 drivers/net/phy/ti.c | 81 ++++++++++++++++++++++++++++++++++++++++++++++------ 1 file changed, 73 insertions(+), 8 deletions(-) -- 2.8.0.rc3 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot