@@ -2284,6 +2284,7 @@ source "board/Marvell/octeontx2/Kconfig"
source "board/armltd/vexpress/Kconfig"
source "board/armltd/vexpress64/Kconfig"
source "board/cortina/presidio-asic/Kconfig"
+source "board/broadcom/bcmns/Kconfig"
source "board/broadcom/bcmns3/Kconfig"
source "board/cavium/thunderx/Kconfig"
source "board/eets/pdu001/Kconfig"
@@ -1173,6 +1173,8 @@ dtb-$(CONFIG_ARCH_BCM283X) += \
bcm2837-rpi-cm3-io3.dtb \
bcm2711-rpi-4-b.dtb
+dtb-$(CONFIG_TARGET_BCMNS) += ns-board.dtb
+
dtb-$(CONFIG_TARGET_BCMNS3) += ns3-board.dtb
dtb-$(CONFIG_ARCH_BCMSTB) += bcm7xxx.dtb
new file mode 100644
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+/dts-v1/;
+
+#include "bcm5301x.dtsi"
+
+/ {
+ /*
+ * The Northstar does not have a proper fallback compatible, but
+ * these basic chips will suffice.
+ */
+ model = "Northstar model";
+ compatible = "brcm,bcm47094", "brcm,bcm4708";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>,
+ <0x88000000 0x08000000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ nand-controller@18028000 {
+ nandcs: nand@0 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * Same as using the bcm5301x-nand-cs0-bch1.dtsi
+ * include from the Linux kernel.
+ */
+ nand-ecc-algo = "bch";
+ nand-ecc-strength = <1>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "brcm,bcm947xx-cfe-partitions";
+ };
+ };
+ };
+};
+
+&uart0 {
+ clock-frequency = <125000000>;
+ status = "okay";
+};
new file mode 100644
@@ -0,0 +1,12 @@
+if TARGET_BCMNS
+
+config SYS_BOARD
+ default "bcmns"
+
+config SYS_VENDOR
+ default "broadcom"
+
+config SYS_CONFIG_NAME
+ default "bcmns"
+
+endif
new file mode 100644
@@ -0,0 +1,6 @@
+BCMNS BOARD
+M: Linus Walleij <linus.walleij@linaro.org>
+S: Maintained
+F: board/broadcom/bcmnsp/
+F: configs/bcmnsp_defconfig
+F: include/configs/bcmnsp.h
new file mode 100644
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+obj-y := ns.o
new file mode 100644
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Broadcom Northstar generic board set-up code
+ * Copyright (C) 2023 Linus Walleij <linus.walleij@linaro.org>
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <init.h>
+#include <log.h>
+#include <ram.h>
+#include <serial.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <asm/armv7m.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+ return fdtdec_setup_mem_size_base();
+}
+
+int dram_init_banksize(void)
+{
+ return fdtdec_setup_memory_banksize();
+}
+
+int board_late_init(void)
+{
+ /* LEDs etc can be initialized here */
+ return 0;
+}
+
+int board_init(void)
+{
+ return 0;
+}
+
+void reset_cpu(void)
+{
+}
+
+int print_cpuinfo(void)
+{
+ printf("BCMNS Northstar SoC\n");
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+int ft_board_setup(void *fdt, struct bd_info *bd)
+{
+ printf("Northstar board setup: DTB at 0x%08lx\n", (ulong)fdt);
+ return 0;
+}
+
new file mode 100644
@@ -0,0 +1,41 @@
+CONFIG_ARM=y
+CONFIG_TARGET_BCMNS=y
+CONFIG_TEXT_BASE=0x00008000
+CONFIG_SYS_MALLOC_LEN=0x2000000
+CONFIG_SYS_MALLOC_F_LEN=0x8000
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_DEFAULT_DEVICE_TREE="ns-board"
+CONFIG_IDENT_STRING="Broadcom Northstar"
+CONFIG_SYS_LOAD_ADDR=0x00008000
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x00100000
+# CONFIG_BOOTSTD is not set
+CONFIG_AUTOBOOT_KEYED=y
+CONFIG_AUTOBOOT_PROMPT="Boot Northstar system in %d seconds\n"
+CONFIG_BOOTDELAY=1
+CONFIG_USE_BOOTCOMMAND=y
+CONFIG_BOOTCOMMAND="run bootcmd_dlink_dir8xxl"
+CONFIG_SYS_PROMPT="northstar> "
+CONFIG_ENV_VARS_UBOOT_CONFIG=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_OF_STDOUT_VIA_ALIAS=y
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_MAXARGS=64
+CONFIG_CMD_SEAMA=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_CACHE=y
+CONFIG_OF_EMBED=y
+CONFIG_USE_HOSTNAME=y
+CONFIG_HOSTNAME="NS"
+CONFIG_CLK=y
+CONFIG_MTD=y
+CONFIG_DM_MTD=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_NAND_BRCMNAND=y
+CONFIG_SYS_NAND_ONFI_DETECTION=y
+CONFIG_CMD_NAND=y
+CONFIG_DM_SERIAL=y
+CONFIG_SYS_NS16550=y
+# CONFIG_NET is not set
+# CONFIG_EFI_LOADER is not set
new file mode 100644
@@ -0,0 +1,49 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+
+#ifndef __BCM_NS_H
+#define __BCM_NS_H
+
+#include <linux/sizes.h>
+
+/* Physical Memory Map */
+#define V2M_BASE 0x00000000
+#define PHYS_SDRAM_1 V2M_BASE
+
+#define CFG_SYS_SDRAM_BASE PHYS_SDRAM_1
+
+/* Called "periph_clk" in Linux, used by the global timer */
+#define CFG_SYS_HZ_CLOCK 500000000
+
+/* Called "iprocslow" in Linux */
+#define CFG_SYS_NS16550_CLK 125000000
+
+/* console configuration */
+#define CONSOLE_ARGS "console_args=console=ttyS0,115200n8\0"
+#define MAX_CPUS "max_cpus=maxcpus=2\0"
+#define EXTRA_ARGS "extra_args=earlycon=uart8250,mmio32,0x18000300\0"
+
+#define BASE_ARGS "${console_args} ${extra_args} ${pcie_args}" \
+ " ${max_cpus} ${log_level} ${reserved_mem}"
+#define SETBOOTARGS "setbootargs=setenv bootargs " BASE_ARGS "\0"
+
+#define KERNEL_LOADADDR_CFG \
+ "loadaddr=0x01000000\0" \
+ "dtb_loadaddr=0x02000000\0"
+
+/*
+ * Hardcoded for the only boards we support, if you add more
+ * boards, add a more clever bootcmd!
+ */
+#define NS_BOOTCMD "bootcmd_dlink_dir8xxl=seama 0x00fe0000; go 0x01000000"
+
+#define ARCH_ENV_SETTINGS \
+ CONSOLE_ARGS \
+ MAX_CPUS \
+ EXTRA_ARGS \
+ KERNEL_LOADADDR_CFG \
+ NS_BOOTCMD
+
+#define CFG_EXTRA_ENV_SETTINGS \
+ ARCH_ENV_SETTINGS
+
+#endif /* __BCM_NS_H */
This adds a simple Northstar "BRCMNS" board to be used with the BCM4709x and BCM5301x chips. The main intention is to use this with the D-Link DIR-890L and DIR-885L routers for loading the kernel into RAM from NAND memory using the BCH-1 ECC and using the separately submitted SEAMA load command, so we are currently not adding support for things such as networking. If other board need other ECC for example, they need to create a separate DTS file and augment the code, but I don't know if any other users will turn up. Cc: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- arch/arm/Kconfig | 1 + arch/arm/dts/Makefile | 2 ++ arch/arm/dts/ns-board.dts | 57 ++++++++++++++++++++++++++++++ board/broadcom/bcmns/Kconfig | 12 +++++++ board/broadcom/bcmns/MAINTAINERS | 6 ++++ board/broadcom/bcmns/Makefile | 2 ++ board/broadcom/bcmns/ns.c | 60 ++++++++++++++++++++++++++++++++ configs/bcmns_defconfig | 41 ++++++++++++++++++++++ include/configs/bcmns.h | 49 ++++++++++++++++++++++++++ 9 files changed, 230 insertions(+) create mode 100644 arch/arm/dts/ns-board.dts create mode 100644 board/broadcom/bcmns/Kconfig create mode 100644 board/broadcom/bcmns/MAINTAINERS create mode 100644 board/broadcom/bcmns/Makefile create mode 100644 board/broadcom/bcmns/ns.c create mode 100644 configs/bcmns_defconfig create mode 100644 include/configs/bcmns.h