diff mbox series

nand: brcmnand: add iproc support

Message ID 20230121234532.2242857-1-linus.walleij@linaro.org
State Superseded
Headers show
Series nand: brcmnand: add iproc support | expand

Commit Message

Linus Walleij Jan. 21, 2023, 11:45 p.m. UTC
Add support for the iproc Broadcom NAND controller,
used in Northstar SoCs for example. Based on the Linux
driver.

Cc: Philippe Reynes <philippe.reynes@softathome.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 drivers/mtd/nand/raw/Kconfig               |   7 +
 drivers/mtd/nand/raw/brcmnand/Makefile     |   1 +
 drivers/mtd/nand/raw/brcmnand/iproc_nand.c | 141 +++++++++++++++++++++
 3 files changed, 149 insertions(+)
 create mode 100644 drivers/mtd/nand/raw/brcmnand/iproc_nand.c

Comments

Linus Walleij March 7, 2023, 11:04 p.m. UTC | #1
On Sun, Jan 22, 2023 at 12:45 AM Linus Walleij <linus.walleij@linaro.org> wrote:

> Add support for the iproc Broadcom NAND controller,
> used in Northstar SoCs for example. Based on the Linux
> driver.
>
> Cc: Philippe Reynes <philippe.reynes@softathome.com>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

It's been 1 1/2 month, could we apply this patch?

Yours,
Linus Walleij
Tom Rini March 8, 2023, 4:54 p.m. UTC | #2
On Wed, Mar 08, 2023 at 12:04:53AM +0100, Linus Walleij wrote:
> On Sun, Jan 22, 2023 at 12:45 AM Linus Walleij <linus.walleij@linaro.org> wrote:
> 
> > Add support for the iproc Broadcom NAND controller,
> > used in Northstar SoCs for example. Based on the Linux
> > driver.
> >
> > Cc: Philippe Reynes <philippe.reynes@softathome.com>
> > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> 
> It's been 1 1/2 month, could we apply this patch?

Adding the nand custodians.
Linus Walleij March 8, 2023, 7:44 p.m. UTC | #3
On Wed, Mar 8, 2023 at 5:54 PM Tom Rini <trini@konsulko.com> wrote:
> On Wed, Mar 08, 2023 at 12:04:53AM +0100, Linus Walleij wrote:
> > On Sun, Jan 22, 2023 at 12:45 AM Linus Walleij <linus.walleij@linaro.org> wrote:
> >
> > > Add support for the iproc Broadcom NAND controller,
> > > used in Northstar SoCs for example. Based on the Linux
> > > driver.
> > >
> > > Cc: Philippe Reynes <philippe.reynes@softathome.com>
> > > Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> >
> > It's been 1 1/2 month, could we apply this patch?
>
> Adding the nand custodians.

Thanks Tom, I need to get better at identifying the right people
for patches.

Yours,
Linus Walleij
Michael Nazzareno Trimarchi March 8, 2023, 8:13 p.m. UTC | #4
Hi

On Sun, Jan 22, 2023 at 12:45 AM Linus Walleij <linus.walleij@linaro.org> wrote:
>
> Add support for the iproc Broadcom NAND controller,
> used in Northstar SoCs for example. Based on the Linux
> driver.
>
> Cc: Philippe Reynes <philippe.reynes@softathome.com>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  drivers/mtd/nand/raw/Kconfig               |   7 +
>  drivers/mtd/nand/raw/brcmnand/Makefile     |   1 +
>  drivers/mtd/nand/raw/brcmnand/iproc_nand.c | 141 +++++++++++++++++++++
>  3 files changed, 149 insertions(+)
>  create mode 100644 drivers/mtd/nand/raw/brcmnand/iproc_nand.c
>
> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
> index 5b35da45f584..6a13bc1e228a 100644
> --- a/drivers/mtd/nand/raw/Kconfig
> +++ b/drivers/mtd/nand/raw/Kconfig
> @@ -156,6 +156,13 @@ config NAND_BRCMNAND_63158
>         help
>           Enable support for broadcom nand driver on bcm63158.
>
> +config NAND_BRCMNAND_IPROC
> +       bool "Support Broadcom NAND controller on the iproc family"
> +       depends on NAND_BRCMNAND
> +       help
> +         Enable support for broadcom nand driver on the Broadcom
> +         iproc family such as Northstar (BCM5301x, BCM4708...)
> +
>  config NAND_DAVINCI
>         bool "Support TI Davinci NAND controller"
>         select SYS_NAND_SELF_INIT if TARGET_DA850EVM
> diff --git a/drivers/mtd/nand/raw/brcmnand/Makefile b/drivers/mtd/nand/raw/brcmnand/Makefile
> index f46a7edae321..0c6325aaa618 100644
> --- a/drivers/mtd/nand/raw/brcmnand/Makefile
> +++ b/drivers/mtd/nand/raw/brcmnand/Makefile
> @@ -6,5 +6,6 @@ obj-$(CONFIG_NAND_BRCMNAND_6753) += bcm6753_nand.o
>  obj-$(CONFIG_NAND_BRCMNAND_68360) += bcm68360_nand.o
>  obj-$(CONFIG_NAND_BRCMNAND_6838) += bcm6838_nand.o
>  obj-$(CONFIG_NAND_BRCMNAND_6858) += bcm6858_nand.o
> +obj-$(CONFIG_NAND_BRCMNAND_IPROC) += iproc_nand.o
>  obj-$(CONFIG_NAND_BRCMNAND) += brcmnand.o
>  obj-$(CONFIG_NAND_BRCMNAND) += brcmnand_compat.o
> diff --git a/drivers/mtd/nand/raw/brcmnand/iproc_nand.c b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
> new file mode 100644
> index 000000000000..c61a120b6d27
> --- /dev/null
> +++ b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
> @@ -0,0 +1,141 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Code borrowed from the Linux driver
> + * Copyright (C) 2015 Broadcom Corporation
> + */
> +
> +#include <common.h>
> +#include <asm/io.h>
> +#include <memalign.h>
> +#include <nand.h>
> +#include <linux/bitops.h>
> +#include <linux/err.h>
> +#include <linux/errno.h>
> +#include <linux/io.h>
> +#include <linux/ioport.h>
> +#include <dm.h>
> +
> +#include "brcmnand.h"
> +
> +struct iproc_nand_soc {
> +       struct brcmnand_soc soc;
> +       void __iomem *idm_base;
> +       void __iomem *ext_base;
> +};
> +
> +#define IPROC_NAND_CTLR_READY_OFFSET   0x10
> +#define IPROC_NAND_CTLR_READY          BIT(0)
> +
> +#define IPROC_NAND_IO_CTRL_OFFSET      0x00
> +#define IPROC_NAND_APB_LE_MODE         BIT(24)
> +#define IPROC_NAND_INT_CTRL_READ_ENABLE        BIT(6)
> +
> +static bool iproc_nand_intc_ack(struct brcmnand_soc *soc)
> +{
> +       struct iproc_nand_soc *priv =
> +                       container_of(soc, struct iproc_nand_soc, soc);
> +       void __iomem *mmio = priv->ext_base + IPROC_NAND_CTLR_READY_OFFSET;
> +       u32 val = brcmnand_readl(mmio);
> +
> +       if (val & IPROC_NAND_CTLR_READY) {
> +               brcmnand_writel(IPROC_NAND_CTLR_READY, mmio);
> +               return true;
> +       }
> +
> +       return false;
> +}
> +
> +static void iproc_nand_intc_set(struct brcmnand_soc *soc, bool en)
> +{
> +       struct iproc_nand_soc *priv =
> +                       container_of(soc, struct iproc_nand_soc, soc);
> +       void __iomem *mmio = priv->idm_base + IPROC_NAND_IO_CTRL_OFFSET;
> +       u32 val = brcmnand_readl(mmio);
> +
> +       if (en)
> +               val |= IPROC_NAND_INT_CTRL_READ_ENABLE;
> +       else
> +               val &= ~IPROC_NAND_INT_CTRL_READ_ENABLE;
> +
> +       brcmnand_writel(val, mmio);
> +}
> +
> +static void iproc_nand_apb_access(struct brcmnand_soc *soc, bool prepare,
> +                                 bool is_param)
> +{
> +       struct iproc_nand_soc *priv =
> +               container_of(soc, struct iproc_nand_soc, soc);
> +       void __iomem *mmio = priv->idm_base + IPROC_NAND_IO_CTRL_OFFSET;
> +       u32 val;
> +
> +       val = brcmnand_readl(mmio);
> +
> +       /*
> +        * In the case of BE or when dealing with NAND data, always configure
> +        * the APB bus to LE mode before accessing the FIFO and back to BE mode
> +        * after the access is done
> +        */
> +       if (IS_ENABLED(CONFIG_SYS_BIG_ENDIAN) || !is_param) {
> +               if (prepare)
> +                       val |= IPROC_NAND_APB_LE_MODE;
> +               else
> +                       val &= ~IPROC_NAND_APB_LE_MODE;
> +       } else { /* when in LE accessing the parameter page, keep APB in BE */
> +               val &= ~IPROC_NAND_APB_LE_MODE;
> +       }
> +
> +       brcmnand_writel(val, mmio);
> +}
> +
> +static int iproc_nand_probe(struct udevice *dev)
> +{
> +       struct udevice *pdev = dev;
> +       struct iproc_nand_soc *priv = dev_get_priv(dev);
> +       struct brcmnand_soc *soc;
> +       struct resource res;
> +
> +       soc = &priv->soc;
> +
> +       dev_read_resource_byname(pdev, "iproc-idm", &res);


Check the return value of dev_read_resource

>
> +       priv->idm_base = ioremap(res.start, resource_size(&res));

To be more close to linux use devm_ioremap.

> +       if (IS_ERR(priv->idm_base))
> +               return PTR_ERR(priv->idm_base);
> +
> +       dev_read_resource_byname(pdev, "iproc-ext", &res);


Check the return value of dev_read_resource

>
> +       priv->ext_base = ioremap(res.start, resource_size(&res));

To be more close to linux use devm_ioremap.

> +       if (IS_ERR(priv->ext_base))
> +               return PTR_ERR(priv->ext_base);
> +
> +       soc->ctlrdy_ack = iproc_nand_intc_ack;
> +       soc->ctlrdy_set_enabled = iproc_nand_intc_set;
> +       soc->prepare_data_bus = iproc_nand_apb_access;
> +
> +       return brcmnand_probe(pdev, soc);
> +}
> +
> +static const struct udevice_id iproc_nand_dt_ids[] = {
> +       {
> +               .compatible = "brcm,nand-iproc",
> +       },
> +       { /* sentinel */ }
> +};
> +
> +U_BOOT_DRIVER(iproc_nand) = {
> +       .name = "iproc-nand",
> +       .id = UCLASS_MTD,
> +       .of_match = iproc_nand_dt_ids,
> +       .probe = iproc_nand_probe,
> +       .priv_auto = sizeof(struct iproc_nand_soc),
> +};
> +
> +void board_nand_init(void)
> +{
> +       struct udevice *dev;
> +       int ret;
> +
> +       ret = uclass_get_device_by_driver(UCLASS_MTD,
> +                                         DM_DRIVER_GET(iproc_nand), &dev);
> +       if (ret && ret != -ENODEV)
> +               pr_err("Failed to initialize %s. (error %d)\n", dev->name,
> +                      ret);
> +}
> --
> 2.39.0
>

Another then that:

Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
diff mbox series

Patch

diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 5b35da45f584..6a13bc1e228a 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -156,6 +156,13 @@  config NAND_BRCMNAND_63158
        help
          Enable support for broadcom nand driver on bcm63158.
 
+config NAND_BRCMNAND_IPROC
+       bool "Support Broadcom NAND controller on the iproc family"
+       depends on NAND_BRCMNAND
+       help
+         Enable support for broadcom nand driver on the Broadcom
+         iproc family such as Northstar (BCM5301x, BCM4708...)
+
 config NAND_DAVINCI
 	bool "Support TI Davinci NAND controller"
 	select SYS_NAND_SELF_INIT if TARGET_DA850EVM
diff --git a/drivers/mtd/nand/raw/brcmnand/Makefile b/drivers/mtd/nand/raw/brcmnand/Makefile
index f46a7edae321..0c6325aaa618 100644
--- a/drivers/mtd/nand/raw/brcmnand/Makefile
+++ b/drivers/mtd/nand/raw/brcmnand/Makefile
@@ -6,5 +6,6 @@  obj-$(CONFIG_NAND_BRCMNAND_6753) += bcm6753_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_68360) += bcm68360_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_6838) += bcm6838_nand.o
 obj-$(CONFIG_NAND_BRCMNAND_6858) += bcm6858_nand.o
+obj-$(CONFIG_NAND_BRCMNAND_IPROC) += iproc_nand.o
 obj-$(CONFIG_NAND_BRCMNAND) += brcmnand.o
 obj-$(CONFIG_NAND_BRCMNAND) += brcmnand_compat.o
diff --git a/drivers/mtd/nand/raw/brcmnand/iproc_nand.c b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
new file mode 100644
index 000000000000..c61a120b6d27
--- /dev/null
+++ b/drivers/mtd/nand/raw/brcmnand/iproc_nand.c
@@ -0,0 +1,141 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Code borrowed from the Linux driver
+ * Copyright (C) 2015 Broadcom Corporation
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <memalign.h>
+#include <nand.h>
+#include <linux/bitops.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <dm.h>
+
+#include "brcmnand.h"
+
+struct iproc_nand_soc {
+	struct brcmnand_soc soc;
+	void __iomem *idm_base;
+	void __iomem *ext_base;
+};
+
+#define IPROC_NAND_CTLR_READY_OFFSET	0x10
+#define IPROC_NAND_CTLR_READY		BIT(0)
+
+#define IPROC_NAND_IO_CTRL_OFFSET	0x00
+#define IPROC_NAND_APB_LE_MODE		BIT(24)
+#define IPROC_NAND_INT_CTRL_READ_ENABLE	BIT(6)
+
+static bool iproc_nand_intc_ack(struct brcmnand_soc *soc)
+{
+	struct iproc_nand_soc *priv =
+			container_of(soc, struct iproc_nand_soc, soc);
+	void __iomem *mmio = priv->ext_base + IPROC_NAND_CTLR_READY_OFFSET;
+	u32 val = brcmnand_readl(mmio);
+
+	if (val & IPROC_NAND_CTLR_READY) {
+		brcmnand_writel(IPROC_NAND_CTLR_READY, mmio);
+		return true;
+	}
+
+	return false;
+}
+
+static void iproc_nand_intc_set(struct brcmnand_soc *soc, bool en)
+{
+	struct iproc_nand_soc *priv =
+			container_of(soc, struct iproc_nand_soc, soc);
+	void __iomem *mmio = priv->idm_base + IPROC_NAND_IO_CTRL_OFFSET;
+	u32 val = brcmnand_readl(mmio);
+
+	if (en)
+		val |= IPROC_NAND_INT_CTRL_READ_ENABLE;
+	else
+		val &= ~IPROC_NAND_INT_CTRL_READ_ENABLE;
+
+	brcmnand_writel(val, mmio);
+}
+
+static void iproc_nand_apb_access(struct brcmnand_soc *soc, bool prepare,
+				  bool is_param)
+{
+	struct iproc_nand_soc *priv =
+		container_of(soc, struct iproc_nand_soc, soc);
+	void __iomem *mmio = priv->idm_base + IPROC_NAND_IO_CTRL_OFFSET;
+	u32 val;
+
+	val = brcmnand_readl(mmio);
+
+	/*
+	 * In the case of BE or when dealing with NAND data, always configure
+	 * the APB bus to LE mode before accessing the FIFO and back to BE mode
+	 * after the access is done
+	 */
+	if (IS_ENABLED(CONFIG_SYS_BIG_ENDIAN) || !is_param) {
+		if (prepare)
+			val |= IPROC_NAND_APB_LE_MODE;
+		else
+			val &= ~IPROC_NAND_APB_LE_MODE;
+	} else { /* when in LE accessing the parameter page, keep APB in BE */
+		val &= ~IPROC_NAND_APB_LE_MODE;
+	}
+
+	brcmnand_writel(val, mmio);
+}
+
+static int iproc_nand_probe(struct udevice *dev)
+{
+	struct udevice *pdev = dev;
+	struct iproc_nand_soc *priv = dev_get_priv(dev);
+	struct brcmnand_soc *soc;
+	struct resource res;
+
+	soc = &priv->soc;
+
+	dev_read_resource_byname(pdev, "iproc-idm", &res);
+	priv->idm_base = ioremap(res.start, resource_size(&res));
+	if (IS_ERR(priv->idm_base))
+		return PTR_ERR(priv->idm_base);
+
+	dev_read_resource_byname(pdev, "iproc-ext", &res);
+	priv->ext_base = ioremap(res.start, resource_size(&res));
+	if (IS_ERR(priv->ext_base))
+		return PTR_ERR(priv->ext_base);
+
+	soc->ctlrdy_ack = iproc_nand_intc_ack;
+	soc->ctlrdy_set_enabled = iproc_nand_intc_set;
+	soc->prepare_data_bus = iproc_nand_apb_access;
+
+	return brcmnand_probe(pdev, soc);
+}
+
+static const struct udevice_id iproc_nand_dt_ids[] = {
+	{
+		.compatible = "brcm,nand-iproc",
+	},
+	{ /* sentinel */ }
+};
+
+U_BOOT_DRIVER(iproc_nand) = {
+	.name = "iproc-nand",
+	.id = UCLASS_MTD,
+	.of_match = iproc_nand_dt_ids,
+	.probe = iproc_nand_probe,
+	.priv_auto = sizeof(struct iproc_nand_soc),
+};
+
+void board_nand_init(void)
+{
+	struct udevice *dev;
+	int ret;
+
+	ret = uclass_get_device_by_driver(UCLASS_MTD,
+					  DM_DRIVER_GET(iproc_nand), &dev);
+	if (ret && ret != -ENODEV)
+		pr_err("Failed to initialize %s. (error %d)\n", dev->name,
+		       ret);
+}