@@ -526,6 +526,7 @@
#define DWC3_DGCMD_SET_ENDPOINT_NRDY 0x0c
#define DWC3_DGCMD_SET_ENDPOINT_PRIME 0x0d
#define DWC3_DGCMD_RUN_SOC_BUS_LOOPBACK 0x10
+#define DWC3_DGCMD_DEV_NOTIFICATION 0x07
#define DWC3_DGCMD_STATUS(n) (((n) >> 12) & 0x0F)
#define DWC3_DGCMD_CMDACT BIT(10)
@@ -72,6 +72,8 @@ dwc3_gadget_generic_cmd_string(u8 cmd)
return "Set Endpoint Prime";
case DWC3_DGCMD_RUN_SOC_BUS_LOOPBACK:
return "Run SoC Bus Loopback Test";
+ case DWC3_DGCMD_DEV_NOTIFICATION:
+ return "Device Notification";
default:
return "UNKNOWN";
}
@@ -30,6 +30,8 @@
static void __dwc3_ep0_do_control_status(struct dwc3 *dwc, struct dwc3_ep *dep);
static void __dwc3_ep0_do_control_data(struct dwc3 *dwc,
struct dwc3_ep *dep, struct dwc3_request *req);
+static int dwc3_ep0_delegate_req(struct dwc3 *dwc,
+ struct usb_ctrlrequest *ctrl);
static void dwc3_ep0_prepare_one_trb(struct dwc3_ep *dep,
dma_addr_t buf_dma, u32 len, u32 type, bool chain)
@@ -367,7 +369,7 @@ static int dwc3_ep0_handle_status(struct dwc3 *dwc,
* Function Remote Wake Capable D0
* Function Remote Wakeup D1
*/
- break;
+ return dwc3_ep0_delegate_req(dwc, ctrl);
case USB_RECIP_ENDPOINT:
dep = dwc3_wIndex_to_dep(dwc, ctrl->wIndex);
@@ -514,13 +516,7 @@ static int dwc3_ep0_handle_intf(struct dwc3 *dwc,
switch (wValue) {
case USB_INTRF_FUNC_SUSPEND:
- /*
- * REVISIT: Ideally we would enable some low power mode here,
- * however it's unclear what we should be doing here.
- *
- * For now, we're not doing anything, just making sure we return
- * 0 so USB Command Verifier tests pass without any errors.
- */
+ ret = dwc3_ep0_delegate_req(dwc, ctrl);
break;
default:
ret = -EINVAL;
@@ -2346,7 +2346,7 @@ static int __dwc3_gadget_wakeup(struct dwc3 *dwc, bool async)
return 0;
/* poll until Link State changes to ON */
- retries = 20000;
+ retries = 30000;
while (retries--) {
reg = dwc3_readl(dwc->regs, DWC3_DSTS);
@@ -2383,6 +2383,39 @@ static int dwc3_gadget_wakeup(struct usb_gadget *g)
return ret;
}
+static void dwc3_resume_gadget(struct dwc3 *dwc);
+
+static int dwc3_gadget_func_wakeup(struct usb_gadget *g, int interface_id)
+{
+ struct dwc3 *dwc = gadget_to_dwc(g);
+ unsigned long flags;
+ int ret;
+
+ spin_lock_irqsave(&dwc->lock, flags);
+ /*
+ * If the link is in LPM, first bring the link to U0
+ * before triggering function remote wakeup.
+ */
+ if (dwc->link_state == DWC3_LINK_STATE_U3) {
+ ret = __dwc3_gadget_wakeup(dwc, false);
+ if (ret) {
+ spin_unlock_irqrestore(&dwc->lock, flags);
+ return -EINVAL;
+ }
+ dwc3_resume_gadget(dwc);
+ dwc->link_state = DWC3_LINK_STATE_U0;
+ }
+
+ ret = dwc3_send_gadget_generic_command(dwc, DWC3_DGCMD_DEV_NOTIFICATION,
+ 0x1 | (interface_id << 4));
+ if (ret)
+ dev_err(dwc->dev, "function remote wakeup failed, ret:%d\n", ret);
+
+ spin_unlock_irqrestore(&dwc->lock, flags);
+
+ return ret;
+}
+
static int dwc3_gadget_set_selfpowered(struct usb_gadget *g,
int is_selfpowered)
{
@@ -3012,6 +3045,7 @@ static void dwc3_gadget_async_callbacks(struct usb_gadget *g, bool enable)
static const struct usb_gadget_ops dwc3_gadget_ops = {
.get_frame = dwc3_gadget_get_frame,
.wakeup = dwc3_gadget_wakeup,
+ .func_wakeup = dwc3_gadget_func_wakeup,
.set_selfpowered = dwc3_gadget_set_selfpowered,
.pullup = dwc3_gadget_pullup,
.udc_start = dwc3_gadget_start,
USB host sends function suspend and function resume notifications to the interface through SET_FEATURE/CLEAR_FEATURE setup packets. Add support to handle these packets by delegating the requests to composite layer. Also add support to handle function wake notification requests to exit from function suspend state. Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> --- drivers/usb/dwc3/core.h | 1 + drivers/usb/dwc3/debug.h | 2 ++ drivers/usb/dwc3/ep0.c | 12 ++++-------- drivers/usb/dwc3/gadget.c | 36 +++++++++++++++++++++++++++++++++++- 4 files changed, 42 insertions(+), 9 deletions(-)