diff mbox series

[v9,09/10] arm64: dts: qcom: Add PMR735d pmic dtsi

Message ID 20230106201047.337409-10-abel.vesa@linaro.org
State New
Headers show
Series arm64: dts: Add base device tree files for SM8550 | expand

Commit Message

Abel Vesa Jan. 6, 2023, 8:10 p.m. UTC 
From: Neil Armstrong <neil.armstrong@linaro.org>

Add nodes for PMR735d in separate dtsi file.

Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 arch/arm64/boot/dts/qcom/pmr735d.dtsi | 104 ++++++++++++++++++++++++++
 1 file changed, 104 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pmr735d.dtsi
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/pmr735d.dtsi b/arch/arm64/boot/dts/qcom/pmr735d.dtsi
new file mode 100644
index 000000000000..41fb664a10b3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmr735d.dtsi
@@ -0,0 +1,104 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pmr735d-k-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmr735d_k_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+
+		pmr735d-l-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmr735d_l_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+
+&spmi_bus {
+	pmr735d_k: pmic@a {
+		compatible = "qcom,pmr735d", "qcom,spmi-pmic";
+		reg = <0xa SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmr735d_k_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0xa 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmr735d_k_gpios: gpio@8800 {
+			compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmr735d_k_gpios 0 0 2>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmr735d_l: pmic@b {
+		compatible = "qcom,pmr735d", "qcom,spmi-pmic";
+		reg = <0xb SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmr735d_l_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0xb 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmr735d_l_gpios: gpio@8800 {
+			compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmr735d_l_gpios 0 0 2>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};