@@ -817,6 +817,7 @@ properties:
- dmo,imx8mm-data-modul-edm-sbc # i.MX8MM eDM SBC
- emtrion,emcon-mx8mm-avari # emCON-MX8MM SoM on Avari Base
- fsl,imx8mm-ddr4-evk # i.MX8MM DDR4 EVK Board
+ - fsl,imx8mm-lpddr4-evk # i.MX8MM LPDDR4 EVK Board
- fsl,imx8mm-evk # i.MX8MM EVK Board
- gateworks,imx8mm-gw7904
- gw,imx8mm-gw71xx-0x # i.MX8MM Gateworks Development Kit
@@ -55,3 +55,133 @@ MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19
>;
};
};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&i2c1 {
+ pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ rohm,reset-snvs-powered;
+
+ #clock-cells = <0>;
+ clocks = <&osc_32k 0>;
+ clock-output-names = "clk-32k-out";
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ // BUCK5 in datasheet
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ // BUCK6 in datasheet
+ regulator-name = "buck4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ // BUCK7 in datasheet
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ // BUCK8 in datasheet
+ regulator-name = "buck6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
@@ -11,118 +11,134 @@
/ {
model = "FSL i.MX8MM EVK board";
compatible = "fsl,imx8mm-evk", "fsl,imx8mm";
-
- aliases {
- spi0 = &flexspi;
- };
};
-&ddrc {
- operating-points-v2 = <&ddrc_opp_table>;
-
- ddrc_opp_table: opp-table {
- compatible = "operating-points-v2";
-
- opp-25M {
- opp-hz = /bits/ 64 <25000000>;
- };
-
- opp-100M {
- opp-hz = /bits/ 64 <100000000>;
- };
-
- opp-750M {
- opp-hz = /bits/ 64 <750000000>;
- };
- };
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
};
-&flexspi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexspi>;
- status = "okay";
-
- flash@0 {
- reg = <0>;
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "jedec,spi-nor";
- spi-max-frequency = <80000000>;
- spi-tx-bus-width = <1>;
- spi-rx-bus-width = <4>;
- };
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
};
-&usdhc3 {
- assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
- assigned-clock-rates = <400000000>;
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc3>;
- pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
- bus-width = <8>;
- non-removable;
- status = "okay";
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
};
-&iomuxc {
- pinctrl_flexspi: flexspigrp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2
- MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
- MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
- MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
- MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
- MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
- >;
- };
-
- pinctrl_usdhc3: usdhc3grp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
- MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
- MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
- MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
- MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
- MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
- MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
- MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
- MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
- MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
- >;
- };
-
- pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
- MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
- MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
- MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
- MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
- MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
- MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
- MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
- MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
- MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
- >;
- };
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
- pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
- fsl,pins = <
- MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
- MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
- MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
- MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
- MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
- MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
- MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
- MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
- MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
- MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
- MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
- >;
+&i2c1 {
+ pmic@4b {
+ compatible = "rohm,bd71847";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ rohm,reset-snvs-powered;
+
+ #clock-cells = <0>;
+ clocks = <&osc_32k 0>;
+ clock-output-names = "clk-32k-out";
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <1250>;
+ rohm,dvs-run-voltage = <1000000>;
+ rohm,dvs-idle-voltage = <900000>;
+ };
+
+ buck3_reg: BUCK3 {
+ // BUCK5 in datasheet
+ regulator-name = "buck3";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ // BUCK6 in datasheet
+ regulator-name = "buck4";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ // BUCK7 in datasheet
+ regulator-name = "buck5";
+ regulator-min-microvolt = <1605000>;
+ regulator-max-microvolt = <1995000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ // BUCK8 in datasheet
+ regulator-name = "buck6";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
};
};
@@ -14,6 +14,10 @@ chosen {
stdout-path = &uart2;
};
+ aliases {
+ spi0 = &flexspi;
+ };
+
memory@40000000 {
device_type = "memory";
reg = <0x0 0x40000000 0 0x80000000>;
@@ -133,20 +137,24 @@ simple-audio-card,codec {
};
};
-&A53_0 {
- cpu-supply = <&buck2_reg>;
-};
+&ddrc {
+ operating-points-v2 = <&ddrc_opp_table>;
-&A53_1 {
- cpu-supply = <&buck2_reg>;
-};
+ ddrc_opp_table: opp-table {
+ compatible = "operating-points-v2";
-&A53_2 {
- cpu-supply = <&buck2_reg>;
-};
+ opp-25M {
+ opp-hz = /bits/ 64 <25000000>;
+ };
+
+ opp-100M {
+ opp-hz = /bits/ 64 <100000000>;
+ };
-&A53_3 {
- cpu-supply = <&buck2_reg>;
+ opp-750M {
+ opp-hz = /bits/ 64 <750000000>;
+ };
+ };
};
&fec1 {
@@ -177,123 +185,27 @@ vddio: vddio-regulator {
};
};
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <80000000>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
&i2c1 {
clock-frequency = <400000>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c1>;
status = "okay";
-
- pmic@4b {
- compatible = "rohm,bd71847";
- reg = <0x4b>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pmic>;
- interrupt-parent = <&gpio1>;
- interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
- rohm,reset-snvs-powered;
-
- #clock-cells = <0>;
- clocks = <&osc_32k 0>;
- clock-output-names = "clk-32k-out";
-
- regulators {
- buck1_reg: BUCK1 {
- regulator-name = "buck1";
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1300000>;
- regulator-boot-on;
- regulator-always-on;
- regulator-ramp-delay = <1250>;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "buck2";
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1300000>;
- regulator-boot-on;
- regulator-always-on;
- regulator-ramp-delay = <1250>;
- rohm,dvs-run-voltage = <1000000>;
- rohm,dvs-idle-voltage = <900000>;
- };
-
- buck3_reg: BUCK3 {
- // BUCK5 in datasheet
- regulator-name = "buck3";
- regulator-min-microvolt = <700000>;
- regulator-max-microvolt = <1350000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- buck4_reg: BUCK4 {
- // BUCK6 in datasheet
- regulator-name = "buck4";
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- buck5_reg: BUCK5 {
- // BUCK7 in datasheet
- regulator-name = "buck5";
- regulator-min-microvolt = <1605000>;
- regulator-max-microvolt = <1995000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- buck6_reg: BUCK6 {
- // BUCK8 in datasheet
- regulator-name = "buck6";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo1_reg: LDO1 {
- regulator-name = "ldo1";
- regulator-min-microvolt = <1600000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "ldo2";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <900000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo3_reg: LDO3 {
- regulator-name = "ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo4_reg: LDO4 {
- regulator-name = "ldo4";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo6_reg: LDO6 {
- regulator-name = "ldo6";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
- };
- };
};
&i2c2 {
@@ -430,6 +342,18 @@ &usdhc2 {
status = "okay";
};
+&usdhc3 {
+ assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+ assigned-clock-rates = <400000000>;
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&wdog1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_wdog>;
@@ -464,6 +388,17 @@ MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
>;
};
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2
+ MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+ >;
+ };
+
pinctrl_gpio_led: gpioledgrp {
fsl,pins = <
MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19
@@ -601,6 +536,55 @@ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
>;
};
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
+ >;
+ };
+
pinctrl_wdog: wdoggrp {
fsl,pins = <
MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x166
new file mode 100644
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019-2020 NXP
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/usb/pd.h>
+#include "imx8mm-evk.dtsi"
+
+/ {
+ model = "FSL i.MX8MM EVK board with LPDDR4";
+ compatible = "fsl,imx8mm-lpddr4-evk", "fsl,imx8mm";
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&i2c1 {
+ pmic: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ nxp,dvs-run-voltage = <820000>;
+ nxp,dvs-standby-voltage = <800000>;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <2187500>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+};
new/current EVKs come with a different PMIC: old(er) ones used to use "rohm,bd71847", which is now replaced "nxp,pca9450a" on the LPDDR4 EVKs to keep backwards compatibility with the old EVK, the nodes are moved into imx8mm-evk.dtsi, with the old boards using imx8mm-evk.dts; while the newer boards get to use imx8mm-lpddr4-evk.dts Signed-off-by: Johannes Schneider <johannes.schneider@leica-geosystems.com> --- .../devicetree/bindings/arm/fsl.yaml | 1 + .../boot/dts/freescale/imx8mm-ddr4-evk.dts | 130 ++++++++++ arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 224 +++++++++-------- arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi | 230 ++++++++---------- .../boot/dts/freescale/imx8mm-lpddr4-evk.dts | 133 ++++++++++ 5 files changed, 491 insertions(+), 227 deletions(-) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-lpddr4-evk.dts