diff mbox series

arm64: dts: qcom: msm8998-yoshino: Use SONY GPIO names

Message ID 20230102190157.970053-1-konrad.dybcio@linaro.org
State New
Headers show
Series arm64: dts: qcom: msm8998-yoshino: Use SONY GPIO names | expand

Commit Message

Konrad Dybcio Jan. 2, 2023, 7:01 p.m. UTC 
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the Yoshino devices DTs to better document the hardware and
rename already-defined GPIO nodes to fit the "official" names.
Note that 4k_ is replaced with four_k_ in one pin, as labels can't start
with numbers.

Lilac and Poplar have identical pin assignments.

Diff between these two and maple:

TLMM:
-  "NC",
+  "TS_VDDIO_EN",

PMI8998:
-  "NC"
+  "USB_SWITCH_SEL"

-  "NC"
+  "4K_DISP_DCDC_EN"

PM8005:
-  "NC"
+  "EAR_EN"

Which is probably due to Maple being designed and released quite a bit
earlier than the other two and it having a super high tech true-4K
display.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../msm8998-sony-xperia-yoshino-maple.dts     | 179 +++++++++++-
 .../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 260 +++++++++++++++---
 2 files changed, 406 insertions(+), 33 deletions(-)

Comments

Dmitry Baryshkov Jan. 3, 2023, 1:07 a.m. UTC | #1 
On 02/01/2023 21:01, Konrad Dybcio wrote:
> Sony ever so graciously provides GPIO line names in their downstream
> kernel (though sometimes they are not 100% accurate and you can judge
> that by simply looking at them and with what drivers they are used).
> 
> Add these to the Yoshino devices DTs to better document the hardware and
> rename already-defined GPIO nodes to fit the "official" names.
> Note that 4k_ is replaced with four_k_ in one pin, as labels can't start
> with numbers.
> 
> Lilac and Poplar have identical pin assignments.
> 
> Diff between these two and maple:
> 
> TLMM:
> -  "NC",
> +  "TS_VDDIO_EN",
> 
> PMI8998:
> -  "NC"
> +  "USB_SWITCH_SEL"
> 
> -  "NC"
> +  "4K_DISP_DCDC_EN"
> 
> PM8005:
> -  "NC"
> +  "EAR_EN"
> 
> Which is probably due to Maple being designed and released quite a bit
> earlier than the other two and it having a super high tech true-4K
> display.
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> ---
>   .../msm8998-sony-xperia-yoshino-maple.dts     | 179 +++++++++++-
>   .../dts/qcom/msm8998-sony-xperia-yoshino.dtsi | 260 +++++++++++++++---


The patch doesn't only add GPIO names, but also changes some labels and 
node names. I can not judge whether they are correct changes or not, but 
they definitely should be split out of the GPIO names patch.


>   2 files changed, 406 insertions(+), 33 deletions(-)
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
index 20fe0394a3c1..e813b41f6db8 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -22,7 +22,7 @@  disp_dvdd_vreg: disp-dvdd-vreg {
 		enable-active-high;
 		gpio = <&pmi8998_gpio 10 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&disp_dvdd_en>;
+		pinctrl-0 = <&four_k_disp_dcdc_en>;
 	};
 };
 
@@ -37,8 +37,30 @@  &lab {
 	qcom,soft-start-us = <200>;
 };
 
+&pm8005_gpio {
+	gpio-line-names = "EAR_EN", /* GPIO_1 */
+			  "NC",
+			  "SLB",
+			  "OPTION_1_PM8005";
+};
+
 &pmi8998_gpio {
-	disp_dvdd_en: disp-dvdd-en-active-state {
+	gpio-line-names = "MAIN_CAM_PWR_IO_EN", /* GPIO_1 */
+			  "NC",
+			  "NC",
+			  "TYPEC_UUSB_SEL",
+			  "VIB_LDO_EN",
+			  "NC",
+			  "DISPLAY_TYPE_SEL",
+			  "USB_SWITCH_SEL",
+			  "NC",
+			  "4K_DISP_DCDC_EN", /* GPIO_10 */
+			  "NC",
+			  "DIV_CLK3",
+			  "SPMI_I2C_SEL",
+			  "NC";
+
+	four_k_disp_dcdc_en: 4k-disp-dcdc-en-state {
 		pins = "gpio10";
 		function = "normal";
 		bias-disable;
@@ -49,6 +71,159 @@  disp_dvdd_en: disp-dvdd-en-active-state {
 	};
 };
 
+&tlmm {
+	gpio-line-names = "", /* GPIO_0 */
+			  "",
+			  "",
+			  "",
+			  "DEBUG_UART_TX",
+			  "DEBUG_UART_RX",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "MDP_VSYNC_P", /* GPIO_10 */
+			  "RGBC_IR_INT",
+			  "NFC_VEN",
+			  "CAM_MCLK0",
+			  "CAM_MCLK1",
+			  "NC",
+			  "NC",
+			  "CCI_I2C_SDA0",
+			  "CCI_I2C_SCL0",
+			  "CCI_I2C_SDA1",
+			  "CCI_I2C_SCL1", /* GPIO_20 */
+			  "MAIN_CAM_PWR_EN",
+			  "TOF_INT_N",
+			  "NC",
+			  "NC",
+			  "CHAT_CAM_PWR_EN",
+			  "NC",
+			  "TOF_RESET_N",
+			  "CAM2_RSTN",
+			  "NC",
+			  "CAM1_RSTN", /* GPIO_30 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "CC_DIR",
+			  "UIM2_DETECT_EN",
+			  "FP_RESET_N", /* GPIO_40 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "BT_HCI_UART_TXD",
+			  "BT_HCI_UART_RXD",
+			  "BT_HCI_UART_CTS_N",
+			  "BT_HCI_UART_RFR_N",
+			  "NC",
+			  "NC", /* GPIO_50 */
+			  "NC",
+			  "NC",
+			  "CODEC_INT2_N",
+			  "CODEC_INT1_N",
+			  "APPS_I2C_SDA",
+			  "APPS_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "TRAY2_DET_DS",
+			  "CODEC_RST_N",
+			  "WSA_L_EN",
+			  "WSA_R_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "LPASS_SLIMBUS_CLK", /* GPIO_70 */
+			  "LPASS_SLIMBUS_DATA0",
+			  "LPASS_SLIMBUS_DATA1",
+			  "BT_FM_SLIMBUS_DATA",
+			  "BT_FM_SLIMBUS_CLK",
+			  "NC",
+			  "RF_LCD_ID_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_80 */
+			  "SW_SERVICE",
+			  "TX_GTR_THRES_IN",
+			  "HW_ID0",
+			  "HW_ID1",
+			  "NC",
+			  "NC",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "TS_RESET_N",
+			  "NC", /* GPIO_90 */
+			  "NC",
+			  "NFC_IRQ",
+			  "NFC_DWLD_EN",
+			  "DISP_RESET_N",
+			  "TRAY2_DET",
+			  "CAM_SOF",
+			  "RFFE6_CLK",
+			  "RFFE6_DATA",
+			  "DEBUG_GPIO0",
+			  "DEBUG_GPIO1", /* GPIO_100 */
+			  "GRFC4",
+			  "NC",
+			  "NC",
+			  "RSVD",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RESET",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK", /* GPIO_110 */
+			  "UIM1_RST",
+			  "UIM1_PRESENT",
+			  "UIM_BATT_ALARM",
+			  "RSVD",
+			  "NC",
+			  "NC",
+			  "ACCEL_INT",
+			  "GYRO_INT",
+			  "COMPASS_INT",
+			  "ALS_PROX_INT_N", /* GPIO_120 */
+			  "FP_INT_N",
+			  "NC",
+			  "BAROMETER_INT",
+			  "ACC_COVER_OPEN",
+			  "TS_INT_N",
+			  "NC",
+			  "NC",
+			  "USB_DETECT_EN",
+			  "NC",
+			  "QLINK_REQUEST", /* GPIO_130 */
+			  "QLINK_ENABLE",
+			  "NC",
+			  "TS_VDDIO_EN",
+			  "WMSS_RESET_N",
+			  "PA_INDICATOR_OR",
+			  "NC",
+			  "RFFE3_DATA",
+			  "RFFE3_CLK",
+			  "RFFE4_DATA",
+			  "RFFE4_CLK", /* GPIO_140 */
+			  "RFFE5_DATA",
+			  "RFFE5_CLK",
+			  "GNSS_EN",
+			  "MSS_LTE_COXM_TXD",
+			  "MSS_LTE_COXM_RXD",
+			  "RFFE2_DATA",
+			  "RFFE2_CLK",
+			  "RFFE1_DATA",
+			  "RFFE1_CLK";
+};
+
 &vreg_l22a_2p85 {
 	regulator-min-microvolt = <2704000>;
 	regulator-max-microvolt = <2704000>;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 5da87baa2b23..a083361a7bc4 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -21,7 +21,7 @@  / {
 	clocks {
 		div1_mclk: divclk1 {
 			compatible = "gpio-gate-clock";
-			pinctrl-0 = <&audio_mclk_pin>;
+			pinctrl-0 = <&div_clk1>;
 			pinctrl-names = "default";
 			clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
 			#clock-cells = <0>;
@@ -46,7 +46,7 @@  cam0_vdig_vreg: cam0-vdig {
 		enable-active-high;
 		gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cam0_vdig_default>;
+		pinctrl-0 = <&main_cam_pwr_en>;
 	};
 
 	cam1_vdig_vreg: cam1-vdig {
@@ -56,7 +56,7 @@  cam1_vdig_vreg: cam1-vdig {
 		enable-active-high;
 		gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cam1_vdig_default>;
+		pinctrl-0 = <&chat_cam_pwr_en>;
 		vin-supply = <&vreg_s3a_1p35>;
 	};
 
@@ -67,7 +67,7 @@  cam_vio_vreg: cam-vio-vreg {
 		enable-active-high;
 		gpio = <&pmi8998_gpio 1 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cam_vio_default>;
+		pinctrl-0 = <&main_cam_pwr_io_en>;
 		vin-supply = <&vreg_lvs1a_1p8>;
 	};
 
@@ -92,15 +92,14 @@  extcon_usb: extcon-usb {
 		id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
 		vbus-gpio = <&tlmm 128 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&usb_extcon_active &usb_vbus_active>;
+		pinctrl-0 = <&cc_dir_default &usb_detect_en>;
 	};
 
 	gpio-keys {
 		compatible = "gpio-keys";
 		label = "Side buttons";
 		pinctrl-names = "default";
-		pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
-			    <&cam_snapshot_pin_a>;
+		pinctrl-0 = <&vol_down_n &focus_n &snapshot_n>;
 		button-vol-down {
 			label = "Volume Down";
 			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
@@ -131,7 +130,7 @@  gpio-hall-sensor {
 		compatible = "gpio-keys";
 		label = "Hall sensors";
 		pinctrl-names = "default";
-		pinctrl-0 = <&hall_sensor0_default>;
+		pinctrl-0 = <&acc_cover_open>;
 
 		event-hall-sensor0 {
 			label = "Cover Hall Sensor";
@@ -189,7 +188,7 @@  vibrator {
 		compatible = "gpio-vibrator";
 		enable-gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&vib_default>;
+		pinctrl-0 = <&vib_ldo_en>;
 	};
 };
 
@@ -263,7 +262,7 @@  proximity@29 {
 		vdd-supply = <&cam_vio_vreg>;
 
 		pinctrl-names = "default";
-		pinctrl-0 = <&tof_int &tof_reset>;
+		pinctrl-0 = <&tof_int_n &tof_reset>;
 	};
 };
 
@@ -292,6 +291,13 @@  &lab {
 	regulator-soft-start;
 };
 
+&pm8005_gpio {
+	gpio-line-names = "NC", /* GPIO_1 */
+			  "NC",
+			  "SLB",
+			  "OPTION_1_PM8005";
+};
+
 &pm8005_regulators {
 	/* VDD_GFX supply */
 	pm8005_s1: s1 {
@@ -304,7 +310,34 @@  pm8005_s1: s1 {
 };
 
 &pm8998_gpio {
-	vol_down_pin_a: vol-down-active-state {
+	gpio-line-names = "UIM_BATT_ALARM", /* GPIO_1 */
+			  "NC",
+			  "WLAN_SW_CTRL (DISALLOWED)",
+			  "SSC_PWR_EN",
+			  "VOL_DOWN_N",
+			  "VOL_UP_N",
+			  "SNAPSHOT_N",
+			  "FOCUS_N",
+			  "FLASH_THERM",
+			  "", /* GPIO_10 */
+			  "",
+			  "",
+			  "DIV_CLK1",
+			  "NC",
+			  "NC (DISALLOWED)",
+			  "DIV_CLK3",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC (DISALLOWED)", /* GPIO_20 */
+			  "NFC_CLK_REQ",
+			  "NC (DISALLOWED)",
+			  "WCSS_PWR_REQ",
+			  "OPTION_1 (DISALLOWED)",
+			  "OPTION_2 (DISALLOWED)",
+			  "PM_SLB (DISALLOWED)";
+
+	vol_down_n: vol-down-n-state {
 		pins = "gpio5";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -312,7 +345,7 @@  vol_down_pin_a: vol-down-active-state {
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_focus_pin_a: cam-focus-btn-active-state {
+	focus_n: focus-n-state {
 		pins = "gpio7";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -320,7 +353,7 @@  cam_focus_pin_a: cam-focus-btn-active-state {
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_snapshot_pin_a: cam-snapshot-btn-active-state {
+	snapshot_n: snapshot-n-state {
 		pins = "gpio8";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -328,7 +361,7 @@  cam_snapshot_pin_a: cam-snapshot-btn-active-state {
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	audio_mclk_pin: audio-mclk-pin-active-state {
+	div_clk1: div-clk1-state {
 		pins = "gpio13";
 		function = "func2";
 		power-source = <0>;
@@ -336,7 +369,22 @@  audio_mclk_pin: audio-mclk-pin-active-state {
 };
 
 &pmi8998_gpio {
-	cam_vio_default: cam-vio-active-state {
+	gpio-line-names = "MAIN_CAM_PWR_IO_EN", /* GPIO_1 */
+			  "NC",
+			  "NC",
+			  "TYPEC_UUSB_SEL",
+			  "VIB_LDO_EN",
+			  "NC",
+			  "DISPLAY_TYPE_SEL",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_10 */
+			  "NC",
+			  "DIV_CLK3",
+			  "SPMI_I2C_SEL",
+			  "NC";
+
+	main_cam_pwr_io_en: main-cam-pwr-io-en-state {
 		pins = "gpio1";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-disable;
@@ -346,7 +394,7 @@  cam_vio_default: cam-vio-active-state {
 		power-source = <1>;
 	};
 
-	vib_default: vib-en-state {
+	vib_ldo_en: vib-ldo-en-state {
 		pins = "gpio5";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-disable;
@@ -595,8 +643,158 @@  &sdhc2 {
 
 &tlmm {
 	gpio-reserved-ranges = <0 4>, <81 4>;
-
-	mdp_vsync_n: mdp-vsync-n-state {
+	gpio-line-names = "", /* GPIO_0 */
+			  "",
+			  "",
+			  "",
+			  "DEBUG_UART_TX",
+			  "DEBUG_UART_RX",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "MDP_VSYNC_P", /* GPIO_10 */
+			  "RGBC_IR_INT",
+			  "NFC_VEN",
+			  "CAM_MCLK0",
+			  "CAM_MCLK1",
+			  "NC",
+			  "NC",
+			  "CCI_I2C_SDA0",
+			  "CCI_I2C_SCL0",
+			  "CCI_I2C_SDA1",
+			  "CCI_I2C_SCL1", /* GPIO_20 */
+			  "MAIN_CAM_PWR_EN",
+			  "TOF_INT_N",
+			  "NC",
+			  "NC",
+			  "CHAT_CAM_PWR_EN",
+			  "NC",
+			  "TOF_RESET_N",
+			  "CAM2_RSTN",
+			  "NC",
+			  "CAM1_RSTN", /* GPIO_30 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "CC_DIR",
+			  "UIM2_DETECT_EN",
+			  "FP_RESET_N", /* GPIO_40 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "BT_HCI_UART_TXD",
+			  "BT_HCI_UART_RXD",
+			  "BT_HCI_UART_CTS_N",
+			  "BT_HCI_UART_RFR_N",
+			  "NC",
+			  "NC", /* GPIO_50 */
+			  "NC",
+			  "NC",
+			  "CODEC_INT2_N",
+			  "CODEC_INT1_N",
+			  "APPS_I2C_SDA",
+			  "APPS_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "TRAY2_DET_DS",
+			  "CODEC_RST_N",
+			  "WSA_L_EN",
+			  "WSA_R_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "LPASS_SLIMBUS_CLK", /* GPIO_70 */
+			  "LPASS_SLIMBUS_DATA0",
+			  "LPASS_SLIMBUS_DATA1",
+			  "BT_FM_SLIMBUS_DATA",
+			  "BT_FM_SLIMBUS_CLK",
+			  "NC",
+			  "RF_LCD_ID_EN",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_80 */
+			  "SW_SERVICE",
+			  "TX_GTR_THRES_IN",
+			  "HW_ID0",
+			  "HW_ID1",
+			  "NC",
+			  "NC",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "TS_RESET_N",
+			  "NC", /* GPIO_90 */
+			  "NC",
+			  "NFC_IRQ",
+			  "NFC_DWLD_EN",
+			  "DISP_RESET_N",
+			  "TRAY2_DET",
+			  "CAM_SOF",
+			  "RFFE6_CLK",
+			  "RFFE6_DATA",
+			  "DEBUG_GPIO0",
+			  "DEBUG_GPIO1", /* GPIO_100 */
+			  "GRFC4",
+			  "NC",
+			  "NC",
+			  "RSVD",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RESET",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK", /* GPIO_110 */
+			  "UIM1_RST",
+			  "UIM1_PRESENT",
+			  "UIM_BATT_ALARM",
+			  "RSVD",
+			  "NC",
+			  "NC",
+			  "ACCEL_INT",
+			  "GYRO_INT",
+			  "COMPASS_INT",
+			  "ALS_PROX_INT_N", /* GPIO_120 */
+			  "FP_INT_N",
+			  "NC",
+			  "BAROMETER_INT",
+			  "ACC_COVER_OPEN",
+			  "TS_INT_N",
+			  "NC",
+			  "NC",
+			  "USB_DETECT_EN",
+			  "NC",
+			  "QLINK_REQUEST", /* GPIO_130 */
+			  "QLINK_ENABLE",
+			  "NC",
+			  "NC",
+			  "WMSS_RESET_N",
+			  "PA_INDICATOR_OR",
+			  "NC",
+			  "RFFE3_DATA",
+			  "RFFE3_CLK",
+			  "RFFE4_DATA",
+			  "RFFE4_CLK", /* GPIO_140 */
+			  "RFFE5_DATA",
+			  "RFFE5_CLK",
+			  "GNSS_EN",
+			  "MSS_LTE_COXM_TXD",
+			  "MSS_LTE_COXM_RXD",
+			  "RFFE2_DATA",
+			  "RFFE2_CLK",
+			  "RFFE1_DATA",
+			  "RFFE1_CLK";
+
+	mdp_vsync_p: mdp-vsync-p-state {
 		pins = "gpio10";
 		function = "mdp_vsync_a";
 		drive-strength = <2>;
@@ -611,14 +809,14 @@  nfc_ven: nfc-ven-state {
 		output-low;
 	};
 
-	msm_mclk0_default: msm-mclk0-active-state {
+	cam_mclk0_active: cam-mclk0-active-state {
 		pins = "gpio13";
 		function = "cam_mclk";
 		drive-strength = <2>;
 		bias-disable;
 	};
 
-	msm_mclk1_default: msm-mclk1-active-state {
+	cam_mclk1_active: cam-mclk1-active-state {
 		pins = "gpio14";
 		function = "cam_mclk";
 		drive-strength = <2>;
@@ -639,14 +837,14 @@  cci1_default: cci1-default-state {
 		drive-strength = <2>;
 	};
 
-	cam0_vdig_default: cam0-vdig-default-state {
+	main_cam_pwr_en: main-cam-pwr-en-default-state {
 		pins = "gpio21";
 		function = "gpio";
 		bias-disable;
 		drive-strength = <2>;
 	};
 
-	tof_int: tof-int-state {
+	tof_int_n: tof-int-n-state {
 		pins = "gpio22";
 		function = "gpio";
 		bias-pull-up;
@@ -654,28 +852,28 @@  tof_int: tof-int-state {
 		input-enable;
 	};
 
-	cam1_vdig_default: cam1-vdig-default-state {
+	chat_cam_pwr_en: chat-cam-pwr-en-default-state {
 		pins = "gpio25";
 		function = "gpio";
 		bias-disable;
 		drive-strength = <2>;
 	};
 
-	usb_extcon_active: usb-extcon-active-state {
-		pins = "gpio38";
+	tof_reset: tof-reset-state {
+		pins = "gpio27";
 		function = "gpio";
 		bias-disable;
-		drive-strength = <16>;
+		drive-strength = <2>;
 	};
 
-	tof_reset: tof-reset-state {
-		pins = "gpio27";
+	cc_dir_default: cc-dir-active-state {
+		pins = "gpio38";
 		function = "gpio";
 		bias-disable;
-		drive-strength = <2>;
+		drive-strength = <16>;
 	};
 
-	hall_sensor0_default: acc-cover-open-state {
+	acc_cover_open: acc-cover-open-state {
 		pins = "gpio124";
 		function = "gpio";
 		bias-disable;
@@ -690,7 +888,7 @@  ts_int_n: ts-int-n-state {
 		bias-pull-up;
 	};
 
-	usb_vbus_active: usb-vbus-active-state {
+	usb_detect_en: usb-detect-en-active-state {
 		pins = "gpio128";
 		function = "gpio";
 		bias-disable;