@@ -351,13 +351,11 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
if (dev->flags & ACCESS_NO_IRQ_SUSPEND) {
dev_pm_set_driver_flags(&pdev->dev,
- DPM_FLAG_SMART_PREPARE |
- DPM_FLAG_MAY_SKIP_RESUME);
+ DPM_FLAG_SMART_PREPARE);
} else {
dev_pm_set_driver_flags(&pdev->dev,
DPM_FLAG_SMART_PREPARE |
- DPM_FLAG_SMART_SUSPEND |
- DPM_FLAG_MAY_SKIP_RESUME);
+ DPM_FLAG_SMART_SUSPEND);
}
device_enable_async_suspend(&pdev->dev);
@@ -419,21 +417,8 @@ static int dw_i2c_plat_prepare(struct device *dev)
*/
return !has_acpi_companion(dev);
}
-
-static void dw_i2c_plat_complete(struct device *dev)
-{
- /*
- * The device can only be in runtime suspend at this point if it has not
- * been resumed throughout the ending system suspend/resume cycle, so if
- * the platform firmware might mess up with it, request the runtime PM
- * framework to resume it.
- */
- if (pm_runtime_suspended(dev) && pm_resume_via_firmware())
- pm_request_resume(dev);
-}
#else
#define dw_i2c_plat_prepare NULL
-#define dw_i2c_plat_complete NULL
#endif
#ifdef CONFIG_PM
@@ -483,7 +468,6 @@ static int __maybe_unused dw_i2c_plat_resume(struct device *dev)
static const struct dev_pm_ops dw_i2c_dev_pm_ops = {
.prepare = dw_i2c_plat_prepare,
- .complete = dw_i2c_plat_complete,
SET_LATE_SYSTEM_SLEEP_PM_OPS(dw_i2c_plat_suspend, dw_i2c_plat_resume)
SET_RUNTIME_PM_OPS(dw_i2c_plat_runtime_suspend, dw_i2c_plat_runtime_resume, NULL)
};
Ensure that i2c_mark_adapter_suspended() is always balanced by a call to i2c_mark_adapter_resumed(). dw_i2c_plat_resume() must always be called, so that i2c_mark_adapter_resumed() is called. This is not compatible with DPM_FLAG_MAY_SKIP_RESUME, so remove the flag. Since the controller is always resumed on system resume the dw_i2c_plat_complete() callback is redundant and has been removed. The unbalanced suspended flag was introduced by commit c57813b8b288 ("i2c: designware: Lock the adapter while setting the suspended flag") Before that commit, the system and runtime PM used the same functions. The DPM_FLAG_MAY_SKIP_RESUME was used to skip the system resume if the driver had been in runtime-suspend. If system resume was skipped, the suspended flag would be cleared by the next runtime resume. The check of the suspended flag was _after_ the call to pm_runtime_get_sync() in i2c_dw_xfer(). So either a system resume or a runtime resume would clear the flag before it was checked. Having introduced the unbalanced suspended flag with that commit, a further commit 80704a84a9f8 ("i2c: designware: Use the i2c_mark_adapter_suspended/resumed() helpers") changed from using a local suspended flag to using the i2c_mark_adapter_suspended/resumed() functions. These use a flag that is checked by I2C core code before issuing the transfer to the bus driver, so there was no opportunity for the bus driver to runtime resume itself before the flag check. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: c57813b8b288 ("i2c: designware: Lock the adapter while setting the suspended flag") --- drivers/i2c/busses/i2c-designware-platdrv.c | 20 ++------------------ 1 file changed, 2 insertions(+), 18 deletions(-)