diff mbox series

[v1] arm64: dts: qcom: sa8540p-ride: enable pcie2a node

Message ID 20221212114502.1616-1-quic_shazhuss@quicinc.com
State New
Headers show
Series [v1] arm64: dts: qcom: sa8540p-ride: enable pcie2a node | expand

Commit Message

Shazad Hussain Dec. 12, 2022, 11:45 a.m. UTC
Add the pcie2a, pcie2a_phy, and respective tlmm
nodes that are needed to get pcie 2a controller
enabled on Qdrive3.

This patch enables 4GB 64bit memory space for
PCIE_2A to have BAR allocations of 64bit pref mem
needed on this Qdrive3 platform with dual SoCs
for root port and switch NT-EP. Hence this ranges
property is overridden in sa8540p-ride.dts only.

Signed-off-by: Shazad Hussain <quic_shazhuss@quicinc.com>
---
This patch depends on below patch series for vreg_l11a.

[v4] arm64: dts: qcom: sa8540p-ride: enable PCIe support
https://lore.kernel.org/all/20221206161916.315640-1-bmasney@redhat.com/

 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 44 +++++++++++++++++++++++
 1 file changed, 44 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
index bb4afd3a9632..ed20423ec8ac 100644
--- a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -146,6 +146,27 @@  vreg_l8g: ldo8 {
 	};
 };
 
+&pcie2a {
+	ranges = <0x01000000 0x0 0x3c200000 0x0 0x3c200000 0x0 0x100000>,
+			 <0x02000000 0x0 0x3c300000 0x0 0x3c300000 0x0 0x1d00000>,
+			 <0x03000000 0x5 0x00000000 0x5 0x00000000 0x1 0x00000000>;
+
+	perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2a_default>;
+
+	status = "okay";
+};
+
+&pcie2a_phy {
+	vdda-phy-supply = <&vreg_l11a>;
+	vdda-pll-supply = <&vreg_l3a>;
+
+	status = "okay";
+};
+
 &pcie3a {
 	ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
 	         <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x20000000>,
@@ -247,6 +268,29 @@  &xo_board_clk {
 /* PINCTRL */
 
 &tlmm {
+	pcie2a_default: pcie2a-default-state {
+		perst-pins {
+			pins = "gpio143";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		clkreq-pins {
+			pins = "gpio142";
+			function = "pcie2a_clkreq";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		wake-pins {
+			pins = "gpio145";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
 	pcie3a_default: pcie3a-default-state {
 		perst-pins {
 			pins = "gpio151";