@@ -236,6 +236,11 @@ config ARCH_NPCM
General support for NPCM8xx BMC (Arbel).
Nuvoton NPCM8xx BMC based on the Cortex A35.
+config ARCH_PHYTIUM
+ bool "Phytium SoC Family"
+ help
+ This enables support for Phytium ARMv8 SoC family.
+
config ARCH_QCOM
bool "Qualcomm Platforms"
select GPIOLIB
@@ -21,6 +21,7 @@ subdir-y += mediatek
subdir-y += microchip
subdir-y += nuvoton
subdir-y += nvidia
+subdir-y += phytium
subdir-y += qcom
subdir-y += realtek
subdir-y += renesas
new file mode 100644
@@ -0,0 +1,5 @@
+dtb-$(CONFIG_ARCH_PHYTIUM) += ft2004-devboard-d4-dsk.dtb
+
+always := $(dtb-y)
+subdir-y := $(dts-dirs)
+clean-files := *.dtb
new file mode 100644
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DTS file for phytium FT-2000/4 devboard (FT-2000/4-D4-DSK series)
+ *
+ * Copyright (C) 2018-2019, Phytium Technology Co., Ltd.
+ */
+
+/dts-v1/;
+/memreserve/ 0x80000000 0x10000;
+
+#include "ft2004-generic-psci-soc.dtsi"
+
+/{
+ model = "FT-2000/4-D4-DSK Development Board";
+ compatible = "phytium,ft-2004";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen {
+ stdout-path = "uart1:115200n8";
+ };
+
+ memory@00{
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x1 0x00000000>;
+ };
+
+ memory@01{
+ device_type = "memory";
+ reg = <0x20 0x00000000 0x1 0x00000000>;
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+};
+
+&rtc0 {
+ status = "ok";
+};
+
+&uart1 {
+ status = "ok";
+};
+
+&gmac0 {
+ status = "ok";
+ phy-mode = "rgmii-rxid";
+};
+
+&gmac1 {
+ status = "ok";
+ phy-mode = "rgmii-rxid";
+};
+
+&spi0 {
+ status = "ok";
+};
+
+&qspi {
+ status = "ok";
+};
+
+&i2c0 {
+ status = "ok";
+};
+
+&i2c1 {
+ status = "ok";
+};
new file mode 100644
@@ -0,0 +1,469 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for FT-2000/4 SoC
+ *
+ * Copyright (C) 2018-2019, Phytium Technology Co., Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "phytium,ft2004";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ cpu_suspend = <0xc4000001>;
+ cpu_off = <0x84000002>;
+ cpu_on = <0xc4000003>;
+ sys_poweroff = <0x84000008>;
+ sys_reset = <0x84000009>;
+ };
+
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ numa-node-id = <0>;
+ clocks = <&scpi_dvfs 0>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ numa-node-id = <0>;
+ clocks = <&scpi_dvfs 0>;
+ };
+
+ cpu2: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ numa-node-id = <0>;
+ clocks = <&scpi_dvfs 1>;
+ };
+
+ cpu3: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,armv8";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ numa-node-id = <0>;
+ clocks = <&scpi_dvfs 1>;
+ };
+ };
+
+ gic: interrupt-controller@29900000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ interrupt-controller;
+ reg = <0x0 0x29900000 0 0x20000>, /* GICD */
+ <0x0 0x29980000 0 0x80000>, /* GICR */
+ <0x0 0x29c00000 0 0x10000>, /* GICC */
+ <0x0 0x29c10000 0 0x10000>, /* GICH */
+ <0x0 0x29c20000 0 0x10000>; /* GICV */
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+
+ its: gic-its@29920000 {
+ compatible = "arm,gic-v3-its";
+ msi-controller;
+ reg = <0x0 0x29920000 0x0 0x20000>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+ clock-frequency = <48000000>;
+ };
+
+ clocks {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ clk250mhz: clk250mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <250000000>;
+ };
+
+ sysclk_48mhz: clk48mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <48000000>;
+ };
+
+ sysclk_600mhz: clk600mhz {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <600000000>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ dma-coherent;
+ ranges;
+
+ gpio0: gpio@28004000 {
+ compatible = "phytium,gpio";
+ reg = <0x0 0x28004000 0x0 0x1000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ porta {
+ compatible = "phytium,gpio-port";
+ reg = <0>;
+ nr-gpios = <8>;
+ };
+
+ portb {
+ compatible = "phytium,gpio-port";
+ reg = <1>;
+ nr-gpios = <8>;
+ };
+ };
+
+ gpio1: gpio@28005000 {
+ compatible = "phytium,gpio";
+ reg = <0x0 0x28005000 0x0 0x1000>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ porta {
+ compatible = "phytium,gpio-port";
+ reg = <0>;
+ nr-gpios = <8>;
+ };
+
+ portb {
+ compatible = "phytium,gpio-port";
+ reg = <1>;
+ nr-gpios = <8>;
+ };
+ };
+
+ uart0: uart@28000000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0x28000000 0x0 0x1000>;
+ baud = <115200>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz &sysclk_48mhz>;
+ clock-names = "uartclk", "apb_pclk";
+ };
+
+ uart1: uart@28001000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0x28001000 0x0 0x1000>;
+ baud = <115200>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz &sysclk_48mhz>;
+ clock-names = "uartclk", "apb_pclk";
+ };
+
+ uart2: uart@28002000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0x28002000 0x0 0x1000>;
+ baud = <115200>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz &sysclk_48mhz>;
+ clock-names = "uartclk", "apb_pclk";
+ };
+
+ uart3: uart@28003000 {
+ compatible = "arm,pl011", "arm,primecell";
+ reg = <0x0 0x28003000 0x0 0x1000>;
+ baud = <115200>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz &sysclk_48mhz>;
+ clock-names = "uartclk", "apb_pclk";
+ };
+
+ sdci: sdci@28207c00 {
+ compatible = "phytium,sdci";
+ reg = <0x0 0x28207c00 0x0 0x100>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_600mhz &sysclk_600mhz>;
+ clock-names = "phytium_sdc_clk";
+ no-sdio;
+ no-mmc;
+ no-dma-coherent;
+ };
+
+ watchdog0: watchdog@2800a000 {
+ compatible = "arm,sbsa-gwdt";
+ reg = <0x0 0x2800b000 0x0 0x1000>,
+ <0x0 0x2800a000 0x0 0x1000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ timeout-sec = <30>;
+ };
+
+ watchdog1: watchdog@28016000 {
+ compatible = "arm,sbsa-gwdt";
+ reg = <0x0 0x28017000 0x0 0x1000>,
+ <0x0 0x28016000 0x0 0x1000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ timeout-sec = <30>;
+ };
+
+ rtc0: rtc@2800d000 {
+ compatible = "phytium,rtc";
+ reg = <0x0 0x2800d000 0x0 0x1000>;
+ clocks = <&sysclk_48mhz>;
+ clock-names = "rtc_pclk";
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@28006000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0x28006000 0x0 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@28007000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0x28007000 0x0 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@28008000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0x28008000 0x0 0x1000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@28009000 {
+ compatible = "snps,designware-i2c";
+ reg = <0x0 0x28009000 0x0 0x1000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz>;
+ status = "disabled";
+ };
+
+ spi0: spi@2800c000 {
+ compatible = "phytium,spi";
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x2800c000 0x0 0x1000>;
+ clocks = <&sysclk_48mhz>;
+ num-cs = <4>;
+ };
+
+ spi1: spi@28013000 {
+ compatible = "phytium,spi";
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0 0x28013000 0x0 0x1000>;
+ clocks = <&sysclk_48mhz>;
+ num-cs = <4>;
+ };
+
+ qspi: qspi@28014000 {
+ compatible = "phytium,qspi";
+ reg = <0x0 0x28014000 0x0 0x1000>,
+ <0x0 0x0 0x0 0x02000000>;
+ reg-names = "qspi", "qspi_mm";
+ clocks = <&sysclk_600mhz>;
+
+ flash@0 {
+ spi-rx-bus-width = <1>;
+ spi-max-frequency = <600000000>;
+ };
+ };
+
+ pcie: pcie {
+ compatible = "pci-host-ecam-generic";
+ device_type = "pci";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ reg = <0x0 0x40000000 0x0 0x10000000>;
+ msi-parent = <&its>;
+ bus-range = <0x0 0xff>;
+ interrupt-map-mask = <0x0 0x0 0x0 0x7>;
+ interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0x0 0x0 0x2 &gic 0x0 0x0 GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0x0 0x0 0x3 &gic 0x0 0x0 GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+ <0x0 0x0 0x0 0x4 &gic 0x0 0x0 GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ ranges = <0x01000000 0x00 0x00000000 0x0 0x50000000 0x0 0x00f00000>,
+ <0x02000000 0x00 0x58000000 0x0 0x58000000 0x0 0x28000000>,
+ <0x03000000 0x10 0x00000000 0x10 0x00000000 0x10 0x00000000>;
+ };
+
+ phytium_axi_setup: stmmac-axi-config {
+ snps,wr_osr_lmt = <0>;
+ snps,rd_osr_lmt = <0>;
+ snps,blen = <0 0 0 0 16 8 4>;
+ };
+
+ gmac0: eth@2820c000 {
+ compatible = "snps,dwmac";
+ reg = <0x0 0x2820c000 0x0 0x2000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&clk250mhz>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+
+ snps,pbl = <16>;
+ snps,fixed-burst;
+ snps,axi-config = <&phytium_axi_setup>;
+ snps,force_sf_dma_mode;
+ snps,multicast-filter-bins = <64>;
+ snps,perfect-filter-entries = <128>;
+ tx-fifo-depth = <4096>;
+ rx-fifo-depth = <4096>;
+ max-frame-size = <9000>;
+ };
+
+ gmac1: eth@28210000 {
+ compatible = "snps,dwmac";
+ reg = <0x0 0x28210000 0x0 0x2000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&clk250mhz>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+
+ snps,pbl = <16>;
+ snps,fixed-burst;
+ snps,axi-config = <&phytium_axi_setup>;
+ snps,force_sf_dma_mode;
+ snps,multicast-filter-bins = <64>;
+ snps,perfect-filter-entries = <128>;
+ snps,rx-queues-to-use = <2>;
+ tx-fifo-depth = <4096>;
+ rx-fifo-depth = <4096>;
+ max-frame-size = <9000>;
+ };
+
+ can0: can@28207000 {
+ compatible = "phytium,can";
+ reg = <0x0 0x28207000 0x0 0x400>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_600mhz>;
+ clock-names = "phytium_can_clk";
+ tx-fifo-depth = <0x40>;
+ rx-fifo-depth = <0x40>;
+ };
+
+ can1: can@28207400 {
+ compatible = "phytium,can";
+ reg = <0x0 0x28207400 0x0 0x400>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_600mhz>;
+ clock-names = "phytium_can_clk";
+ tx-fifo-depth = <0x40>;
+ rx-fifo-depth = <0x40>;
+ };
+
+ can2: can@028207800 {
+ compatible = "phytium,can";
+ reg = <0x0 0x28207800 0x0 0x400>;
+ interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_600mhz>;
+ clock-names = "phytium_can_clk";
+ tx-fifo-depth = <0x40>;
+ rx-fifo-depth = <0x40>;
+ };
+
+ hda: hda@28206000 {
+ compatible = "phytium,hda";
+ reg = <0 0x28206000 0x0 0x1000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sysclk_48mhz>;
+ clock-names = "phytium_hda_clk";
+ };
+
+ mbox: mailbox@2a000000 {
+ compatible = "phytium,mbox";
+ reg = <0x0 0x2a000000 0x0 0x1000>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ #mbox-cells = <1>;
+ clocks = <&sysclk_48mhz>;
+ clock-names = "apb_pclk";
+ };
+
+ sram: sram@2a006000 {
+ compatible = "phytium,ft2004-sram-ns","mmio-sram";
+ reg = <0x0 0x2a006000 0x0 0x2000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x2a006000 0x2000>;
+
+ scpi_lpri: scpi-shmem@0 {
+ compatible = "phytium,ft2004-scpi-shmem";
+ reg = <0x1000 0x800>;
+ };
+ };
+
+ scpi_protocol: scpi {
+ compatible = "arm,scpi";
+ mboxes = <&mbox 0>;
+ shmem = <&scpi_lpri>;
+
+ clocks {
+ compatible = "arm,scpi-clocks";
+
+ scpi_dvfs: scpi_clocks@0 {
+ compatible = "arm,scpi-dvfs-clocks";
+ #clock-cells = <1>;
+ clock-indices = <0>, <1>;
+ clock-output-names = "c0", "c1";
+ };
+ };
+
+ scpi_sensors: sensors {
+ compatible = "arm,scpi-sensors";
+ #thermal-sensor-cells = <1>;
+ };
+ };
+ };
+};
@@ -904,6 +904,7 @@ static const struct of_device_id shmem_of_match[] __maybe_unused = {
{ .compatible = "amlogic,meson-axg-scp-shmem", },
{ .compatible = "arm,juno-scp-shmem", },
{ .compatible = "arm,scp-shmem", },
+ { .compatible = "phytium,ft2004-scpi-shmem", },
{ }
};
arm64/boot/dts and arm_scpi: add to support Phytium FT2004 CPU. Signed-off-by: Wang Honghui <honghui.wang@ucas.com.cn> --- arch/arm64/Kconfig.platforms | 5 + arch/arm64/boot/dts/Makefile | 1 + arch/arm64/boot/dts/phytium/Makefile | 5 + .../dts/phytium/ft2004-devboard-d4-dsk.dts | 73 +++ .../dts/phytium/ft2004-generic-psci-soc.dtsi | 469 ++++++++++++++++++ drivers/firmware/arm_scpi.c | 1 + 6 files changed, 554 insertions(+) create mode 100644 arch/arm64/boot/dts/phytium/Makefile create mode 100644 arch/arm64/boot/dts/phytium/ft2004-devboard-d4-dsk.dts create mode 100644 arch/arm64/boot/dts/phytium/ft2004-generic-psci-soc.dtsi