@@ -11,6 +11,7 @@
#include <dt-bindings/interconnect/qcom,sm6350.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/phy/phy-qcom-qmp.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -1119,50 +1120,25 @@ usb_1_hsphy: phy@88e3000 {
resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
};
- usb_1_qmpphy: phy@88e9000 {
- compatible = "qcom,sc7180-qmp-usb3-dp-phy";
- reg = <0 0x088e9000 0 0x200>,
- <0 0x088e8000 0 0x40>,
- <0 0x088ea000 0 0x200>;
- status = "disabled";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
+ usb_1_qmpphy: phy@88e8000 {
+ compatible = "qcom,sm6350-qmp-usb3-dp-phy";
+ reg = <0 0x088e8000 0 0x3000>;
clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
<&xo_board>,
<&rpmhcc RPMH_QLINK_CLK>,
- <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
- clock-names = "aux", "cfg_ahb", "ref", "com_aux";
+ <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+ <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+ clock-names = "aux", "cfg_ahb", "ref", "com_aux", "usb3_pipe";
resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
<&gcc GCC_USB3_PHY_PRIM_BCR>;
reset-names = "phy", "common";
- usb_1_ssphy: usb3-phy@88e9200 {
- reg = <0 0x088e9200 0 0x200>,
- <0 0x088e9400 0 0x200>,
- <0 0x088e9c00 0 0x400>,
- <0 0x088e9600 0 0x200>,
- <0 0x088e9800 0 0x200>,
- <0 0x088e9a00 0 0x100>;
- #clock-cells = <0>;
- #phy-cells = <0>;
- clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
- clock-names = "pipe0";
- clock-output-names = "usb3_phy_pipe_clk_src";
- };
+ #clock-cells = <1>;
+ #phy-cells = <1>;
- dp_phy: dp-phy@88ea200 {
- reg = <0 0x088ea200 0 0x200>,
- <0 0x088ea400 0 0x200>,
- <0 0x088eac00 0 0x400>,
- <0 0x088ea600 0 0x200>,
- <0 0x088ea800 0 0x200>,
- <0 0x088eaa00 0 0x100>;
- #phy-cells = <0>;
- #clock-cells = <1>;
- };
+ status = "disabled";
};
dc_noc: interconnect@9160000 {
@@ -1236,7 +1212,7 @@ usb_1_dwc3: usb@a600000 {
snps,dis_enblslpm_quirk;
snps,has-lpm-erratum;
snps,hird-threshold = /bits/ 8 <0x10>;
- phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+ phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
phy-names = "usb2-phy", "usb3-phy";
};
};
The sc7180 phy compatible works fine for some cases, but it turns out sm6350 does need proper phy configuration in the driver, so use the newly added sm6350 compatible. Because the sm6350 compatible is using the new binding, we need to change the node quite a bit to match it. This fixes qmpphy init when no USB cable is plugged in during bootloader stage. Signed-off-by: Luca Weiss <luca.weiss@fairphone.com> --- @Johan Hovold, in this patch there's also the question about cfg_ahb, power-domains but I'm also not happy about using the QMP_USB43DP_USB3_PHY define for the phy reference. Do you think it's a good idea to introduce e.g. QMP_USB3DP_USB3_PHY with the same value so it's essentially just an alias to the other? This series is tested on next-20221124 with next branch of linux-phy repo (commit bea3ce759b46) merged in. arch/arm64/boot/dts/qcom/sm6350.dtsi | 46 +++++++--------------------- 1 file changed, 11 insertions(+), 35 deletions(-)