@@ -48,6 +48,7 @@ Optional properties:
locating ECC errors for BCHx algorithms. SoC devices which have
ELM hardware engines should specify this device node in .dtsi
Using ELM for ECC error correction frees some CPU cycles.
+ - rb-gpios: GPIO specifier for the ready/busy# pin.
For inline partition table parsing (optional):
@@ -78,6 +79,7 @@ Example for an AM33xx board:
ti,nand-xfer-type = "polled";
interrupt-parent = <&gpmc>;
interrupts = <0>, <1>;
+ rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
@@ -12,6 +12,7 @@
#include <linux/dmaengine.h>
#include <linux/dma-mapping.h>
#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/jiffies.h>
@@ -183,6 +184,8 @@ struct omap_nand_info {
struct nand_ecclayout oobinfo;
/* fields specific for BCHx_HW ECC scheme */
struct device *elm_dev;
+ /* NAND ready gpio */
+ struct gpio_desc *ready_gpiod;
};
static inline struct omap_nand_info *mtd_to_omap(struct mtd_info *mtd)
@@ -1024,21 +1027,16 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip)
}
/**
- * omap_dev_ready - calls the platform specific dev_ready function
+ * omap_dev_ready - checks the NAND Ready GPIO line
* @mtd: MTD device structure
+ *
+ * Returns true if ready and false if busy.
*/
static int omap_dev_ready(struct mtd_info *mtd)
{
- unsigned int val = 0;
struct omap_nand_info *info = mtd_to_omap(mtd);
- val = readl(info->reg.gpmc_status);
-
- if ((val & 0x100) == 0x100) {
- return 1;
- } else {
- return 0;
- }
+ return gpiod_get_value(info->ready_gpiod);
}
/**
@@ -1754,7 +1752,9 @@ static int omap_nand_probe(struct platform_device *pdev)
info->gpmc_cs = pdata->cs;
info->reg = pdata->reg;
info->ecc_opt = pdata->ecc_opt;
- info->dev_ready = pdata->dev_ready;
+ if (pdata->dev_ready)
+ dev_info(&pdev->dev, "pdata->dev_ready is deprecated\n");
+
info->xfer_type = pdata->xfer_type;
info->devsize = pdata->devsize;
info->elm_of_node = pdata->elm_of_node;
@@ -1786,6 +1786,13 @@ static int omap_nand_probe(struct platform_device *pdev)
nand_chip->IO_ADDR_W = nand_chip->IO_ADDR_R;
nand_chip->cmd_ctrl = omap_hwcontrol;
+ info->ready_gpiod = devm_gpiod_get_optional(&pdev->dev, "rb",
+ GPIOD_IN);
+ if (IS_ERR(info->ready_gpiod)) {
+ dev_err(dev, "failed to get ready gpio\n");
+ return PTR_ERR(info->ready_gpiod);
+ }
+
/*
* If RDY/BSY line is connected to OMAP then use the omap ready
* function and the generic nand_wait function which reads the status
@@ -1793,7 +1800,7 @@ static int omap_nand_probe(struct platform_device *pdev)
* chip delay which is slightly more than tR (AC Timing) of the NAND
* device and read status register until you get a failure or success
*/
- if (info->dev_ready) {
+ if (info->ready_gpiod) {
nand_chip->dev_ready = omap_dev_ready;
nand_chip->chip_delay = 0;
} else {
@@ -71,7 +71,6 @@ struct omap_nand_platform_data {
int cs;
struct mtd_partition *parts;
int nr_parts;
- bool dev_ready;
bool flash_bbt;
enum nand_io xfer_type;
int devsize;
@@ -82,5 +81,6 @@ struct omap_nand_platform_data {
/* deprecated */
struct gpmc_nand_regs reg;
struct device_node *of_node;
+ bool dev_ready;
};
#endif
The GPMC WAIT pin status are now available over gpiolib. Update the omap_dev_ready() function to use gpio instead of directly accessing GPMC register space. Signed-off-by: Roger Quadros <rogerq@ti.com> --- .../devicetree/bindings/mtd/gpmc-nand.txt | 2 ++ drivers/mtd/nand/omap2.c | 29 ++++++++++++++-------- include/linux/platform_data/mtd-nand-omap2.h | 2 +- 3 files changed, 21 insertions(+), 12 deletions(-) -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html