@@ -195,6 +195,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.tcl_ring_retry = true,
.tx_ring_size = DP_TCL_DATA_RING_SIZE,
.smp2p_wow_exit = false,
+ .support_fw_mac_sequence = false,
},
{
.name = "qca6390 hw2.0",
@@ -277,6 +278,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.tcl_ring_retry = true,
.tx_ring_size = DP_TCL_DATA_RING_SIZE,
.smp2p_wow_exit = false,
+ .support_fw_mac_sequence = true,
},
{
.name = "qcn9074 hw1.0",
@@ -356,6 +358,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.tcl_ring_retry = true,
.tx_ring_size = DP_TCL_DATA_RING_SIZE,
.smp2p_wow_exit = false,
+ .support_fw_mac_sequence = false,
},
{
.name = "wcn6855 hw2.0",
@@ -438,6 +441,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.tcl_ring_retry = true,
.tx_ring_size = DP_TCL_DATA_RING_SIZE,
.smp2p_wow_exit = false,
+ .support_fw_mac_sequence = true,
},
{
.name = "wcn6855 hw2.1",
@@ -519,6 +523,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.tcl_ring_retry = true,
.tx_ring_size = DP_TCL_DATA_RING_SIZE,
.smp2p_wow_exit = false,
+ .support_fw_mac_sequence = true,
},
{
.name = "wcn6750 hw1.0",
@@ -597,6 +602,7 @@ static const struct ath11k_hw_params ath11k_hw_params[] = {
.tcl_ring_retry = false,
.tx_ring_size = DP_TCL_DATA_RING_SIZE_WCN6750,
.smp2p_wow_exit = true,
+ .support_fw_mac_sequence = true,
},
};
@@ -219,6 +219,7 @@ struct ath11k_hw_params {
bool tcl_ring_retry;
u32 tx_ring_size;
bool smp2p_wow_exit;
+ bool support_fw_mac_sequence;
};
struct ath11k_hw_ops {
@@ -8045,6 +8045,13 @@ ath11k_mac_op_reconfig_complete(struct ieee80211_hw *hw,
ath11k_dbg(ab, ATH11K_DBG_BOOT, "reset success\n");
}
}
+ if (ar->ab->hw_params.support_fw_mac_sequence) {
+ list_for_each_entry(arvif, &ar->arvifs, list) {
+ if (arvif->is_up && arvif->vdev_type == WMI_VDEV_TYPE_STA)
+ ieee80211_hw_restart_disconnect(arvif->vif);
+ }
+ }
+
}
mutex_unlock(&ar->conf_mutex);
Currently after the hardware restart triggered from the driver, the station interface connection remains intact, since a disconnect trigger is not sent to userspace. This can lead to a problem in targets where the wifi mac sequence is added by the firmware. After the target restart, its wifi mac sequence number gets reset to zero. Hence AP to which our device is connected will receive frames with a wifi mac sequence number jump to the past, thereby resulting in the AP dropping all these frames, until the frame arrives with a wifi mac sequence number which AP was expecting. To avoid such frame drops, its better to trigger a station disconnect upon target hardware restart which can be done with API ieee80211_reconfig_disconnect exposed to mac80211. The other targets are not affected by this change, since the hardware params flag is not set. Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com> --- drivers/net/wireless/ath/ath11k/core.c | 6 ++++++ drivers/net/wireless/ath/ath11k/hw.h | 1 + drivers/net/wireless/ath/ath11k/mac.c | 7 +++++++ 3 files changed, 14 insertions(+)