diff mbox series

[v11,2/2] arm64: dts: qcom: sagit: add initial device tree for sagit

Message ID 20221102155558.1895829-3-dsankouski@gmail.com
State Superseded
Headers show
Series add device Xiaomi Mi 6 (codename sagit) and board binding | expand

Commit Message

Dzmitry Sankouski Nov. 2, 2022, 3:55 p.m. UTC
New device support - Xiaomi Mi6 phone

What works:
- storage
- usb
- power regulators

Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
---
Changes for v2:
- remove memory nodes before redefining
- add board compatible to schema
- remove board msm-id, add chassis type
- remove common dtsi
- move resin to pm8998 dtsi file
- dts formatting
- unsupported properties removed
- add copyright
- rebase on latest master(6.0.0-rc6)
Changes for v3:
- regulators nodes renamed to match pattern 'regulators-[01]'
- duplicate cci1-default node deleted
- add state suffix to '.*(active|suspend|default)' pinctrl
- rebase on latest master(6.0.0)
Changes for v4:
- fix dts compilation errors(rename pinctrl label usages)
Changes for v5:
- use pm8005_regulators label
Changes for v6:
- add state suffix to all pinctrl
- move status nodes to last position
- disable resin node by default
- move the debounce param to pm8998.dtsi file
- place this patch after dt-binding patch
Changes for v7:
- fix Properties must precede subnodes dts compilation error
Changes for v8:
- enable resin node
- rename nodes in reserved memory to comply with 'memory@.*' pattern
Changes for v9: none
Changes for v10:
- reorder resin node content
- reorder reserved memory nodes
- increase reserved memory for adsp to comply with vendor kernel
- new line in blsp1_uart3 node
Changes for v11:
- rebase on v6.1-rc3
- add missing regulator to qusb2phy node

 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/msm8998-xiaomi-sagit.dts    | 711 ++++++++++++++++++
 arch/arm64/boot/dts/qcom/pm8998.dtsi          |   8 +
 3 files changed, 720 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts

Comments

Krzysztof Kozlowski Nov. 2, 2022, 7:20 p.m. UTC | #1
On 02/11/2022 11:55, Dzmitry Sankouski wrote:
> New device support - Xiaomi Mi6 phone
> 
> What works:
> - storage
> - usb
> - power regulators
> 
> Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> ---

(...)

> +
> +&blsp1_i2c5_sleep {
> +	/delete-property/ bias-pull-up;
> +	bias-disable;
> +};
> +
> +&blsp1_uart3 {
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "qcom,wcn3990-bt";
> +
> +		vddio-supply = <&vreg_s4a_1p8>;
> +		vddxo-supply = <&vreg_l7a_1p8>;
> +		vddrf-supply = <&vreg_l17a_1p3>;
> +		vddch0-supply = <&vreg_l25a_3p3>;
> +		max-speed = <3200000>;
> +	};
> +};
> +
> +&blsp1_uart3_on {
> +	rx {

This is a friendly reminder during the review process.

It seems my previous comments were not fully addressed. Maybe my
feedback got lost between the quotes, maybe you just forgot to apply it.
Please go back to the previous discussion and either implement all
requested changes or keep discussing them.

Thank you.

6.1-rc3 is not a proper rebase... You *must* include maintainers'
entries. This *must* align with stuff has Bjorn. Also I expect it passes
dtbs_check on stuff in the next.

Best regards,
Krzysztof
Dzmitry Sankouski Nov. 7, 2022, 2:24 p.m. UTC | #2
Is the master branch of
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git
proper rebase?
Or do I need to search and apply device tree doc patches somehow
before running dtbs_check?
I rebased on linux-next/master, and my dts is ok.

A lot of warnings for msm8998.dtsi, though. I think it should be fixed
in a separate patch series.

ср, 2 нояб. 2022 г. в 22:20, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org>:
>
> On 02/11/2022 11:55, Dzmitry Sankouski wrote:
> > New device support - Xiaomi Mi6 phone
> >
> > What works:
> > - storage
> > - usb
> > - power regulators
> >
> > Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
> > ---
>
> (...)
>
> > +
> > +&blsp1_i2c5_sleep {
> > +     /delete-property/ bias-pull-up;
> > +     bias-disable;
> > +};
> > +
> > +&blsp1_uart3 {
> > +     status = "okay";
> > +
> > +     bluetooth {
> > +             compatible = "qcom,wcn3990-bt";
> > +
> > +             vddio-supply = <&vreg_s4a_1p8>;
> > +             vddxo-supply = <&vreg_l7a_1p8>;
> > +             vddrf-supply = <&vreg_l17a_1p3>;
> > +             vddch0-supply = <&vreg_l25a_3p3>;
> > +             max-speed = <3200000>;
> > +     };
> > +};
> > +
> > +&blsp1_uart3_on {
> > +     rx {
>
> This is a friendly reminder during the review process.
>
> It seems my previous comments were not fully addressed. Maybe my
> feedback got lost between the quotes, maybe you just forgot to apply it.
> Please go back to the previous discussion and either implement all
> requested changes or keep discussing them.
>
> Thank you.
>
> 6.1-rc3 is not a proper rebase... You *must* include maintainers'
> entries. This *must* align with stuff has Bjorn. Also I expect it passes
> dtbs_check on stuff in the next.
>
> Best regards,
> Krzysztof
>
Dzmitry Sankouski Nov. 10, 2022, 9:28 a.m. UTC | #3
пн, 7 нояб. 2022 г. в 17:33, Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org>:
>
> On 07/11/2022 15:24, Dzmitry Sankouski wrote:
(...)
> > A lot of warnings for msm8998.dtsi, though. I think it should be fixed
> > in a separate patch series.
>
> Your DTS is not OK and it introduces wrong pinctrl entry, which I
> commented under. It also does not pass test, as I said:
My bad, I'll fix that
>
(...)
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index d7669a7cee9f..660edacbb7ee 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -49,6 +49,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-oneplus-dumpling.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-lilac.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-maple.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-sony-xperia-yoshino-poplar.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-xiaomi-sagit.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
new file mode 100644
index 000000000000..2ed29c95edc4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8998-xiaomi-sagit.dts
@@ -0,0 +1,711 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Xiaomi Mi 6 (sagit) device tree source based on msm8998-mtp.dtsi
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Degdag Mohamed <degdagmohamed@gmail.com>
+ * Copyright (c) 2022, Dzmitry Sankouski <dsankouski@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/*
+ * Delete following upstream (msm8998.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &adsp_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &mba_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &wlan_msa_mem;
+
+/ {
+	model = "Xiaomi Mi 6";
+	compatible = "xiaomi,sagit", "qcom,msm8998";
+	chassis-type = "handset";
+	/* Required for bootloader to select correct board */
+	qcom,board-id = <30 0>;
+
+	reserved-memory {
+		/*
+		 * Xiaomi's ADSP firmware requires 30 MiB in total, so increase the adsp_mem
+		 * region by 4 MiB to account for this while relocating the other now
+		 * conflicting memory nodes accordingly.
+		 */
+		adsp_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x1e00000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8d000000 {
+			reg = <0x0 0x8d000000 0x0 0x7000000>;
+			no-map;
+		};
+
+		venus_mem: memory@94000000 {
+			reg = <0x0 0x94000000 0x0 0x500000>;
+			no-map;
+		};
+
+		mba_mem: memory@94500000 {
+			reg = <0x0 0x94500000 0x0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@94700000 {
+			reg = <0x0 0x94700000 0x0 0xf00000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@95600000 {
+			reg = <0x0 0x95600000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@95610000 {
+			reg = <0x0 0x95610000 0x0 0x5000>;
+			no-map;
+		};
+
+		gpu_mem: memory@95615000 {
+			reg = <0x0 0x95615000 0x0 0x100000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@95715000 {
+			reg = <0x0 0x95715000 0x0 0x100000>;
+			no-map;
+		};
+
+		/* Bootloader display framebuffer region */
+		cont_splash_mem: memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x2400000>;
+			no-map;
+		};
+
+		/* For getting crash logs using Android downstream kernels */
+		ramoops@ac000000 {
+			compatible = "ramoops";
+			reg = <0x0 0xac000000 0x0 0x200000>;
+			console-size = <0x80000>;
+			pmsg-size = <0x40000>;
+			record-size = <0x8000>;
+			ftrace-size = <0x20000>;
+		};
+
+		/*
+		 * The following memory regions on downstream are "dynamically allocated"
+		 * but given the same addresses every time. Hard code them as these addresses
+		 * are where the Xiaomi signed firmware expects them to be.
+		 */
+		ipa_fws_region: memory@f7800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7800000 0x0 0x5000>;
+			no-map;
+		};
+
+		zap_shader_region: memory@f7900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xf7900000 0x0 0x2000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		label = "Volume buttons";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_key_default>;
+
+		key-vol-up {
+			label = "Volume up";
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+			wakeup-source;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+		label = "Hall effect sensor";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hall_sensor_default_state>;
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	disp_vddts_vreg: disp-vddts-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "disp-vddts-regulator";
+		gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+};
+
+&blsp1_i2c5 {
+	pinctrl-names = "default", "sleep";
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ts_active_state>;
+		pinctrl-1 = <&ts_int_suspend_state &ts_reset_suspend_state>;
+
+		vdd-supply = <&disp_vddts_vreg>;
+		vio-supply = <&vreg_l6a_1p8>;
+
+		syna,reset-delay-ms = <20>;
+		syna,startup-delay-ms = <20>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			touchscreen-x-mm = <64>;
+			touchscreen-y-mm = <114>;
+			syna,sensor-type = <1>;
+			syna,rezero-wait-ms = <20>;
+		};
+
+		rmi4-f1a@1a {
+			reg = <0x1a>;
+			syna,codes = <KEY_BACK KEY_APPSELECT>;
+		};
+	};
+};
+
+&blsp1_i2c5_sleep {
+	/delete-property/ bias-pull-up;
+	bias-disable;
+};
+
+&blsp1_uart3 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 46 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+};
+
+&pm8005_regulators {
+	compatible = "qcom,pm8005-regulators";
+
+	vdd_s1-supply = <&vph_pwr>;
+
+	pm8005_s1: s1 { /* VDD_GFX supply */
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
+
+		/* hack until we rig up the gpu consumer */
+		regulator-always-on;
+	};
+};
+
+&pm8998_gpio {
+	vol_up_key_default: vol-up-key-default-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+
+	audio_mclk_pin: audio-mclk-pin-active-state {
+		pins = "gpio13";
+		function = "func2";
+		power-source = <0>;
+	};
+};
+
+&qusb2phy {
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+	status = "okay";
+};
+
+&rpm_requests {
+	regulators-0 {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l14a_1p8: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a_2p7: l18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l19a_3p0: l19 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l22a_2p85: l22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <2864000>;
+		};
+
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 { };
+
+		vreg_lvs2a_1p8: lvs2 { };
+	};
+
+	regulators-1 {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	cci1_default_state: cci1-default-state {
+		pins = "gpio19", "gpio20";
+		function = "cci_i2c";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	cdc_reset_n_state: cdc-reset-n-state {
+		pins = "gpio64";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <16>;
+		output-high;
+	};
+
+	hall_sensor_default_state: hall-sensor-default-state {
+		pins = "gpio124";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	mdss_dsi_active_state: mdss-dsi-active-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	mdss_dsi_suspend_state: mdss-dsi-suspend-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_active_state: mdss-te-active-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	mdss_te_suspend_state: mdss-te-suspend-state {
+		pins = "gpio10";
+		function = "mdp_vsync_a";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk0_active_state: msm-mclk0-active-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk0_suspend_state: msm-mclk0-suspend-state {
+		pins = "gpio13";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	msm_mclk1_active_state: msm-mclk1-active-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	msm_mclk1_suspend_state: msm-mclk1-suspend-state {
+		pins = "gpio14";
+		function = "cam_mclk";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	nfc_int_active_state: nfc-int-active-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_int_suspend_state: nfc-int-suspend-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_active_state: nfc-enable-active-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_suspend_state: nfc-enable-suspend-state {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	ts_active_state: ts-active-state {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	ts_int_suspend_state: ts-int-suspend-state {
+		pins = "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	ts_reset_suspend_state: ts-reset-suspend-state {
+		pins = "gpio89";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcd_int_n_state: wcd-int-n-state {
+		pins = "gpio54";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	wsa_leftspk_pwr_n_state: wsa-leftspk-pwr-n-state {
+		pins = "gpio65";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+
+	wsa_rightspk_pwr_n_state: wsa-rightspk-pwr-n-state {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+};
+
+&pm8998_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+	status = "okay";
+};
+
+&ufshc {
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l26a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vcc-max-microamp = <750000>;
+	vccq-max-microamp = <560000>;
+	vccq2-max-microamp = <750000>;
+	status = "okay";
+};
+
+&ufsphy {
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+	status = "okay";
+};
+
+&usb3 {
+	/* Disable USB3 clock requirement as the device only supports USB2 */
+	qcom,select-utmi-as-pipe-clk;
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	/* Drop the unused USB 3 PHY */
+	phys = <&qusb2phy>;
+	phy-names = "usb2-phy";
+
+	/* Fastest mode for USB 2 */
+	maximum-speed = "high-speed";
+
+	/* Force to peripheral until we can switch modes */
+	dr_mode = "peripheral";
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index d09f2954b6f9..fabee4b71677 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -52,6 +52,14 @@  pm8998_pwrkey: pwrkey {
 				bias-pull-up;
 				linux,code = <KEY_POWER>;
 			};
+
+			pm8998_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
 		};
 
 		pm8998_temp: temp-alarm@2400 {