deleted file mode 100644
@@ -1,202 +0,0 @@
-Qualcomm MSM8998 TLMM block
-
-This binding describes the Top Level Mode Multiplexer block found in the
-MSM8998 platform.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be "qcom,msm8998-pinctrl"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: the base address and size of the TLMM register space.
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: should specify the TLMM summary IRQ.
-
-- interrupt-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as an interrupt controller
-
-- #interrupt-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/interrupt-controller/irq.h>
-
-- gpio-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as a gpio controller
-
-- #gpio-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/gpio/gpio.h>
-
-- gpio-ranges:
- Usage: required
- Definition: see ../gpio/gpio.txt
-
-- gpio-reserved-ranges:
- Usage: optional
- Definition: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-
-PIN CONFIGURATION NODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
- Usage: required
- Value type: <string-array>
- Definition: List of gpio pins affected by the properties specified in
- this subnode.
-
- Valid pins are:
- gpio0-gpio149
- Supports mux, bias and drive-strength
-
- sdc2_clk, sdc2_cmd, sdc2_data
- Supports bias and drive-strength
-
- ufs_reset
- Supports bias and drive-strength
-
-- function:
- Usage: required
- Value type: <string>
- Definition: Specify the alternative function to be configured for the
- specified pins. Functions are only valid for gpio pins.
- Valid values are:
-
- gpio, adsp_ext, agera_pll, atest_char, atest_gpsadc0,
- atest_gpsadc1, atest_tsens, atest_tsens2, atest_usb1,
- atest_usb10, atest_usb11, atest_usb12, atest_usb13,
- audio_ref, bimc_dte0, bimc_dte1, blsp10_spi, blsp10_spi_a,
- blsp10_spi_b, blsp11_i2c, blsp1_spi, blsp1_spi_a,
- blsp1_spi_b, blsp2_spi, blsp9_spi, blsp_i2c1, blsp_i2c2,
- blsp_i2c3, blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7,
- blsp_i2c8, blsp_i2c9, blsp_i2c10, blsp_i2c11, blsp_i2c12,
- blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5,
- blsp_spi6, blsp_spi7, blsp_spi8, blsp_spi9, blsp_spi10,
- blsp_spi11, blsp_spi12, blsp_uart1_a, blsp_uart1_b,
- blsp_uart2_a, blsp_uart2_b, blsp_uart3_a, blsp_uart3_b,
- blsp_uart7_a, blsp_uart7_b, blsp_uart8, blsp_uart8_a,
- blsp_uart8_b, blsp_uart9_a, blsp_uart9_b, blsp_uim1_a,
- blsp_uim1_b, blsp_uim2_a, blsp_uim2_b, blsp_uim3_a,
- blsp_uim3_b, blsp_uim7_a, blsp_uim7_b, blsp_uim8_a,
- blsp_uim8_b, blsp_uim9_a, blsp_uim9_b, bt_reset,
- btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
- cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng,
- cri_trng0, cri_trng1, dbg_out, ddr_bist, edp_hot, edp_lcd,
- gcc_gp1_a, gcc_gp1_b, gcc_gp2_a, gcc_gp2_b, gcc_gp3_a,
- gcc_gp3_b, hdmi_cec, hdmi_ddc, hdmi_hot, hdmi_rcv,
- isense_dbg, jitter_bist, ldo_en, ldo_update, lpass_slimbus,
- m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2,
- mdp_vsync3, mdp_vsync_a, mdp_vsync_b, modem_tsync, mss_lte,
- nav_dr, nav_pps, pa_indicator, pci_e0, phase_flag,
- pll_bypassnl, pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc,
- pwr_crypto, pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b,
- qdss_cti1_a, qdss_cti1_b, qdss, qlink_enable,
- qlink_request, qua_mi2s, sd_card, sd_write, sdc40, sdc41,
- sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu,
- spkr_i2s, ssbi1, ssc_irq, ter_mi2s, tgu_ch0, tgu_ch1,
- tsense_pwm1, tsense_pwm2, tsif0, tsif1,
- uim1_clk, uim1_data, uim1_present,
- uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
- uim_batt, usb_phy, vfr_1, vsense_clkout, vsense_data0,
- vsense_data1, vsense_mode, wlan1_adc0, wlan1_adc1,
- wlan2_adc0, wlan2_adc1,
-
-- bias-disable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as no pull.
-
-- bias-pull-down:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull down.
-
-- bias-pull-up:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull up.
-
-- output-high:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- high.
- Not valid for sdc pins.
-
-- output-low:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- low.
- Not valid for sdc pins.
-
-- drive-strength:
- Usage: optional
- Value type: <u32>
- Definition: Selects the drive strength for the specified pins, in mA.
- Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
-
-Example:
-
- tlmm: pinctrl@03400000 {
- compatible = "qcom,msm8998-pinctrl";
- reg = <0x03400000 0xc00000>;
- interrupts = <0 208 0>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&tlmm 0 0 175>;
- gpio-reserved-ranges = <0 4>, <81 4>;
- interrupt-controller;
- #interrupt-cells = <2>;
-
- uart_console_active: uart_console_active {
- mux {
- pins = "gpio4", "gpio5";
- function = "blsp_uart8_a";
- };
-
- config {
- pins = "gpio4", "gpio5";
- drive-strength = <2>;
- bias-disable;
- };
- };
- };
new file mode 100644
@@ -0,0 +1,171 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8998-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm MSM8998 TLMM pin controller
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller in Qualcomm MSM8998 SoC.
+
+properties:
+ compatible:
+ const: qcom,msm8998-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 75
+
+ gpio-line-names:
+ maxItems: 150
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-msm8998-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-msm8998-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-msm8998-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-4][0-9])$"
+ - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+
+ enum: [ gpio, adsp_ext, agera_pll, atest_char, atest_gpsadc0,
+ atest_gpsadc1, atest_tsens, atest_tsens2, atest_usb1,
+ atest_usb10, atest_usb11, atest_usb12, atest_usb13, audio_ref,
+ bimc_dte0, bimc_dte1, blsp10_spi, blsp10_spi_a, blsp10_spi_b,
+ blsp11_i2c, blsp1_spi, blsp1_spi_a, blsp1_spi_b, blsp2_spi,
+ blsp9_spi, blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4,
+ blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_i2c9,
+ blsp_i2c10, blsp_i2c11, blsp_i2c12, blsp_spi1, blsp_spi2,
+ blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
+ blsp_spi8, blsp_spi9, blsp_spi10, blsp_spi11, blsp_spi12,
+ blsp_uart1_a, blsp_uart1_b, blsp_uart2_a, blsp_uart2_b,
+ blsp_uart3_a, blsp_uart3_b, blsp_uart7_a, blsp_uart7_b,
+ blsp_uart8, blsp_uart8_a, blsp_uart8_b, blsp_uart9_a,
+ blsp_uart9_b, blsp_uim1_a, blsp_uim1_b, blsp_uim2_a,
+ blsp_uim2_b, blsp_uim3_a, blsp_uim3_b, blsp_uim7_a,
+ blsp_uim7_b, blsp_uim8_a, blsp_uim8_b, blsp_uim9_a,
+ blsp_uim9_b, bt_reset, btfm_slimbus, cam_mclk, cci_async,
+ cci_i2c, cci_timer0, cci_timer1, cci_timer2, cci_timer3,
+ cci_timer4, cri_trng, cri_trng0, cri_trng1, dbg_out, ddr_bist,
+ edp_hot, edp_lcd, gcc_gp1_a, gcc_gp1_b, gcc_gp2_a, gcc_gp2_b,
+ gcc_gp3_a, gcc_gp3_b, hdmi_cec, hdmi_ddc, hdmi_hot, hdmi_rcv,
+ isense_dbg, jitter_bist, ldo_en, ldo_update, lpass_slimbus,
+ m_voc, mdp_vsync, mdp_vsync0, mdp_vsync1, mdp_vsync2,
+ mdp_vsync3, mdp_vsync_a, mdp_vsync_b, modem_tsync, mss_lte,
+ nav_dr, nav_pps, pa_indicator, pci_e0, phase_flag,
+ pll_bypassnl, pll_reset, pri_mi2s, pri_mi2s_ws, prng_rosc,
+ pwr_crypto, pwr_modem, pwr_nav, qdss_cti0_a, qdss_cti0_b,
+ qdss_cti1_a, qdss_cti1_b, qdss, qlink_enable, qlink_request,
+ qua_mi2s, sd_card, sd_write, sdc40, sdc41, sdc42, sdc43,
+ sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, spkr_i2s, ssbi1, ssc_irq,
+ ter_mi2s, tgu_ch0, tgu_ch1, tsense_pwm1, tsense_pwm2, tsif0,
+ tsif1, uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk,
+ uim2_data, uim2_present, uim2_reset, uim_batt, usb_phy, vfr_1,
+ vsense_clkout, vsense_data0, vsense_data1, vsense_mode,
+ wlan1_adc0, wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
+
+ bias-pull-down: true
+ bias-pull-up: true
+ bias-disable: true
+ drive-strength: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ tlmm: pinctrl@3400000 {
+ compatible = "qcom,msm8998-pinctrl";
+ reg = <0x03400000 0xc00000>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&tlmm 0 0 150>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-reserved-ranges = <0 4>, <81 4>;
+
+ sdc2-off-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2-cd-state {
+ pins = "gpio95";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };