deleted file mode 100644
@@ -1,187 +0,0 @@
-Qualcomm Technologies, Inc. SC7180 TLMM block
-
-This binding describes the Top Level Mode Multiplexer block found in the
-SC7180 platform.
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be "qcom,sc7180-pinctrl"
-
-- reg:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: the base address and size of the north, south and west
- TLMM tiles
-
-- reg-names:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: names for the cells of reg, must contain "north", "south"
- and "west".
-
-- interrupts:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: should specify the TLMM summary IRQ.
-
-- interrupt-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as an interrupt controller
-
-- #interrupt-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/interrupt-controller/irq.h>
-
-- gpio-controller:
- Usage: required
- Value type: <none>
- Definition: identifies this node as a gpio controller
-
-- #gpio-cells:
- Usage: required
- Value type: <u32>
- Definition: must be 2. Specifying the pin number and flags, as defined
- in <dt-bindings/gpio/gpio.h>
-
-- gpio-ranges:
- Usage: required
- Value type: <prop-encoded-array>
- Definition: see ../gpio/gpio.txt
-
-- gpio-reserved-ranges:
- Usage: optional
- Value type: <prop-encoded-array>
- Definition: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-The pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-
-PIN CONFIGURATION NODES:
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
-
-- pins:
- Usage: required
- Value type: <string-array>
- Definition: List of gpio pins affected by the properties specified in
- this subnode.
-
- Valid pins are:
- gpio0-gpio118
- Supports mux, bias and drive-strength
-
- sdc1_clk, sdc1_cmd, sdc1_data sdc2_clk, sdc2_cmd,
- sdc2_data sdc1_rclk
- Supports bias and drive-strength
-
- ufs_reset
- Supports bias and drive-strength
-
-- function:
- Usage: required
- Value type: <string>
- Definition: Specify the alternative function to be configured for the
- specified pins. Functions are only valid for gpio pins.
- Valid values are:
-
- adsp_ext, agera_pll, aoss_cti, atest_char, atest_char0,
- atest_char1, atest_char2, atest_char3, atest_tsens,
- atest_tsens2, atest_usb1, atest_usb10, atest_usb11,
- atest_usb12, atest_usb13, atest_usb2, atest_usb20,
- atest_usb21, atest_usb22, atest_usb23, audio_ref,
- btfm_slimbus, cam_mclk, cci_async, cci_i2c, cci_timer0,
- cci_timer1, cci_timer2, cci_timer3, cci_timer4,
- cri_trng, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1,
- ddr_pxi2, ddr_pxi3, dp_hot, edp_lcd, gcc_gp1, gcc_gp2,
- gcc_gp3, gpio, gp_pdm0, gp_pdm1, gp_pdm2, gps_tx,
- jitter_bist, ldo_en, ldo_update, lpass_ext, mdp_vsync,
- mdp_vsync0, mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s_0,
- mi2s_1, mi2s_2, mss_lte, m_voc, pa_indicator, phase_flag,
- PLL_BIST, pll_bypassnl, pll_reset, prng_rosc, qdss,
- qdss_cti, qlink_enable, qlink_request, qspi_clk, qspi_cs,
- qspi_data, qup00, qup01, qup02_i2c, qup02_uart, qup03,
- qup04_i2c, qup04_uart, qup05, qup10, qup11_i2c, qup11_uart,
- qup12, qup13_i2c, qup13_uart, qup14, qup15, sdc1_tb,
- sdc2_tb, sd_write, sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2,
- tgu_ch3, tsense_pwm1, tsense_pwm2, uim1, uim2, uim_batt,
- usb_phy, vfr_1, _V_GPIO, _V_PPS_IN, _V_PPS_OUT,
- vsense_trigger, wlan1_adc0, wlan1_adc1, wlan2_adc0,
- wlan2_adc1,
-
-- bias-disable:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as no pull.
-
-- bias-pull-down:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull down.
-
-- bias-pull-up:
- Usage: optional
- Value type: <none>
- Definition: The specified pins should be configured as pull up.
-
-- output-high:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- high.
- Not valid for sdc pins.
-
-- output-low:
- Usage: optional
- Value type: <none>
- Definition: The specified pins are configured in output mode, driven
- low.
- Not valid for sdc pins.
-
-- drive-strength:
- Usage: optional
- Value type: <u32>
- Definition: Selects the drive strength for the specified pins, in mA.
- Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
-
-Example:
-
- tlmm: pinctrl@3500000 {
- compatible = "qcom,sc7180-pinctrl";
- reg = <0x3500000 0x300000>,
- <0x3900000 0x300000>,
- <0x3D00000 0x300000>;
- reg-names = "west", "north", "south";
- interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&tlmm 0 0 119>;
- gpio-reserved-ranges = <0 4>, <106 4>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
new file mode 100644
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,sc7180-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SC7180 TLMM pin controller
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller in Qualcomm SC7180 SoC.
+
+properties:
+ compatible:
+ const: qcom,sc7180-pinctrl
+
+ reg:
+ maxItems: 3
+
+ reg-names:
+ items:
+ - const: west
+ - const: north
+ - const: south
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 60
+
+ gpio-line-names:
+ maxItems: 119
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-sc7180-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-sc7180-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-sc7180-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|10[0-9]|11[0-8])$"
+ - enum: [ sdc1_rclk, sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk,
+ sdc2_cmd, sdc2_data, ufs_reset ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+
+ enum: [ adsp_ext, agera_pll, aoss_cti, atest_char, atest_char0,
+ atest_char1, atest_char2, atest_char3, atest_tsens,
+ atest_tsens2, atest_usb1, atest_usb10, atest_usb11,
+ atest_usb12, atest_usb13, atest_usb2, atest_usb20, atest_usb21,
+ atest_usb22, atest_usb23, audio_ref, btfm_slimbus, cam_mclk,
+ cci_async, cci_i2c, cci_timer0, cci_timer1, cci_timer2,
+ cci_timer3, cci_timer4, cri_trng, dbg_out, ddr_bist, ddr_pxi0,
+ ddr_pxi1, ddr_pxi2, ddr_pxi3, dp_hot, edp_lcd, gcc_gp1,
+ gcc_gp2, gcc_gp3, gpio, gp_pdm0, gp_pdm1, gp_pdm2, gps_tx,
+ jitter_bist, ldo_en, ldo_update, lpass_ext, mdp_vsync,
+ mdp_vsync0, mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s_0, mi2s_1,
+ mi2s_2, mss_lte, m_voc, pa_indicator, phase_flag, PLL_BIST,
+ pll_bypassnl, pll_reset, prng_rosc, qdss, qdss_cti,
+ qlink_enable, qlink_request, qspi_clk, qspi_cs, qspi_data,
+ qup00, qup01, qup02_i2c, qup02_uart, qup03, qup04_i2c,
+ qup04_uart, qup05, qup10, qup11_i2c, qup11_uart, qup12,
+ qup13_i2c, qup13_uart, qup14, qup15, sdc1_tb, sdc2_tb,
+ sd_write, sp_cmu, tgu_ch0, tgu_ch1, tgu_ch2, tgu_ch3,
+ tsense_pwm1, tsense_pwm2, uim1, uim2, uim_batt, usb_phy, vfr_1,
+ _V_GPIO, _V_PPS_IN, _V_PPS_OUT, vsense_trigger, wlan1_adc0,
+ wlan1_adc1, wlan2_adc0, wlan2_adc1 ]
+
+ drive-strength:
+ enum: [2, 4, 6, 8, 10, 12, 14, 16]
+ description:
+ Selects the drive strength for the specified pins, in mA.
+
+ bias-pull-down: true
+ bias-pull-up: true
+ bias-disable: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ additionalProperties: false
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+required:
+ - compatible
+ - reg
+ - reg-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ tlmm: pinctrl@3500000 {
+ compatible = "qcom,sc7180-pinctrl";
+ reg = <0x03500000 0x300000>,
+ <0x03900000 0x300000>,
+ <0x03d00000 0x300000>;
+ reg-names = "west", "north", "south";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&tlmm 0 0 120>;
+ wakeup-parent = <&pdc>;
+
+ dp_hot_plug_det: dp-hot-plug-det-state {
+ pins = "gpio117";
+ function = "dp_hot";
+ };
+
+ qup_spi11_cs_gpio: qup-spi11-cs-gpio-state {
+ spi-pins {
+ pins = "gpio53", "gpio54", "gpio55";
+ function = "qup15";
+ };
+
+ cs-pins {
+ pins = "gpio56";
+ function = "gpio";
+ };
+ };
+ };