diff mbox series

[8/8] MIPS: DTS: Ingenic: Add support for the JZ4755 SoC

Message ID 20221009181338.2896660-9-lis8215@gmail.com
State New
Headers show
Series MIPS: ingenic: Add support for the JZ4755 SoC | expand

Commit Message

Siarhei Volkau Oct. 9, 2022, 6:13 p.m. UTC 
Add preliminary support for boards based on the JZ4755 SoC from
Ingenic.

It is a low-power SoC with a MIPS32r1 SoC running at ~432 MHz, and no
FPU.

The JZ4755 SoC is supposed to be newer than the JZ4725B SoC, but its
internals are very close to each other. So JZ4755 DT is reusing many
JZ4725b drivers because JZ4725b support in the kernel appears earlier.

Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
---
 arch/mips/boot/dts/ingenic/jz4755.dtsi | 439 +++++++++++++++++++++++++
 1 file changed, 439 insertions(+)
 create mode 100644 arch/mips/boot/dts/ingenic/jz4755.dtsi

Comments

Krzysztof Kozlowski Oct. 10, 2022, 2:54 p.m. UTC | #1 
On 09/10/2022 14:13, Siarhei Volkau wrote:
> Add preliminary support for boards based on the JZ4755 SoC from
> Ingenic.
> 
> It is a low-power SoC with a MIPS32r1 SoC running at ~432 MHz, and no
> FPU.
> 
> The JZ4755 SoC is supposed to be newer than the JZ4725B SoC, but its
> internals are very close to each other. So JZ4755 DT is reusing many
> JZ4725b drivers because JZ4725b support in the kernel appears earlier.
> 
> Signed-off-by: Siarhei Volkau <lis8215@gmail.com>
> ---
>  arch/mips/boot/dts/ingenic/jz4755.dtsi | 439 +++++++++++++++++++++++++

How do you build it? How do you test it? It's basically non-compillable,
dead code. You need a board.

Best regards,
Krzysztof
Krzysztof Kozlowski Oct. 11, 2022, 12:09 p.m. UTC | #2 
On 10/10/2022 16:00, Siarhei Volkau wrote:
>> How do you build it? How do you test it? It's basically non-compillable,
>> dead code. You need a board.
> 
> I tested it on a Ritmix RZX-50 handheld, 

You cannot, there is no such DTS.

> although this patchset doesn't
> include it as it requires many other changes to be fully functional.

Exactly.

> I decided to do this in two steps: add platform first (this patchset) then
> specific drivers and quirks, in the next patchset, when this one passes.
> 
> Of course I can add machine's dts with working parts. What's the usual way?

Don't add dead code to the kernel, so DTSI comes with DTS.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/mips/boot/dts/ingenic/jz4755.dtsi b/arch/mips/boot/dts/ingenic/jz4755.dtsi
new file mode 100644
index 000000000..e1630e0fe
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/jz4755.dtsi
@@ -0,0 +1,439 @@ 
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/ingenic,jz4755-cgu.h>
+#include <dt-bindings/clock/ingenic,tcu.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "ingenic,jz4755";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "ingenic,xburst-mxu1.1";
+			reg = <0>;
+
+			clocks = <&cgu JZ4755_CLK_CCLK>;
+			clock-names = "cpu";
+		};
+	};
+
+	cpuintc: interrupt-controller {
+		#address-cells = <0>;
+		#interrupt-cells = <1>;
+		interrupt-controller;
+		compatible = "mti,cpu-interrupt-controller";
+	};
+
+	intc: interrupt-controller@10001000 {
+		compatible = "ingenic,jz4725b-intc", "ingenic,jz4740-intc";
+		reg = <0x10001000 0x14>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <2>;
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+	};
+
+	osc32k: osc32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+
+	cgu: clock-controller@10000000 {
+		compatible = "ingenic,jz4755-cgu";
+		reg = <0x10000000 0x100>;
+
+		clocks = <&ext>, <&osc32k>;
+		clock-names = "ext", "osc32k";
+
+		#clock-cells = <1>;
+	};
+
+	uart0: serial@10030000 {
+		compatible = "ingenic,jz4755-uart", "ingenic,jz4750-uart";
+		reg = <0x10030000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <9>;
+
+		clocks = <&cgu JZ4755_CLK_EXT_HALF>, <&cgu JZ4755_CLK_UART0>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart1: serial@10031000 {
+		compatible = "ingenic,jz4755-uart", "ingenic,jz4750-uart";
+		reg = <0x10031000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <8>;
+
+		clocks = <&cgu JZ4755_CLK_EXT_HALF>, <&cgu JZ4755_CLK_UART1>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	uart2: serial@10032000 {
+		compatible = "ingenic,jz4755-uart", "ingenic,jz4750-uart";
+		reg = <0x10032000 0x100>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <7>;
+
+		clocks = <&cgu JZ4755_CLK_EXT_HALF>, <&cgu JZ4755_CLK_UART2>;
+		clock-names = "baud", "module";
+
+		status = "disabled";
+	};
+
+	rtc_dev: rtc@10003000 {
+		compatible = "ingenic,jz4725b-rtc", "ingenic,jz4740-rtc";
+		reg = <0x10003000 0x40>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <6>;
+
+		clocks = <&cgu JZ4755_CLK_RTC>;
+		clock-names = "rtc";
+	};
+
+	pinctrl: pinctrl@10010000 {
+		compatible = "ingenic,jz4755-pinctrl";
+		reg = <0x10010000 0x600>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpa: gpio@0 {
+			compatible = "ingenic,jz4755-gpio";
+			reg = <0>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 0 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <16>;
+		};
+
+		gpb: gpio@1 {
+			compatible = "ingenic,jz4755-gpio";
+			reg = <1>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 32 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <15>;
+		};
+
+		gpc: gpio@2 {
+			compatible = "ingenic,jz4755-gpio";
+			reg = <2>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 64 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <14>;
+		};
+
+		gpd: gpio@3 {
+			compatible = "ingenic,jz4755-gpio";
+			reg = <3>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 96 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <13>;
+		};
+
+		gpe: gpio@4 {
+			compatible = "ingenic,jz4755-gpio";
+			reg = <4>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 128 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <12>;
+		};
+
+		gpf: gpio@5 {
+			compatible = "ingenic,jz4755-gpio";
+			reg = <5>;
+
+			gpio-controller;
+			gpio-ranges = <&pinctrl 0 160 32>;
+			#gpio-cells = <2>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			interrupt-parent = <&intc>;
+			interrupts = <11>;
+		};
+	};
+
+	mmc0: mmc@10021000 {
+		compatible = "ingenic,jz4725b-mmc";
+		reg = <0x10021000 0x1000>;
+
+		clocks = <&cgu JZ4755_CLK_MMC0>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <25>;
+
+		dmas = <&dmac1 27 0xffffffff>, <&dmac1 26 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	mmc1: mmc@10022000 {
+		compatible = "ingenic,jz4725b-mmc";
+		reg = <0x10022000 0x1000>;
+
+		clocks = <&cgu JZ4755_CLK_MMC1>;
+		clock-names = "mmc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <24>;
+
+		dmas = <&dmac1 31 0xffffffff>, <&dmac1 30 0xffffffff>;
+		dma-names = "rx", "tx";
+
+		cap-sd-highspeed;
+		cap-mmc-highspeed;
+		cap-sdio-irq;
+	};
+
+	dmac0: dma-controller@13020000 {
+		compatible = "ingenic,jz4755-dma";
+		reg = <0x13020000 0xd0>, <0x13020300 0x14>;
+
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <29>;
+
+		clocks = <&cgu JZ4755_CLK_DMA>;
+	};
+
+	dmac1: dma-controller@13020100 {
+		compatible = "ingenic,jz4755-dma";
+		reg = <0x13020100 0xd0>, <0x13020400 0x14>;
+
+		#dma-cells = <2>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <28>;
+
+		clocks = <&cgu JZ4755_CLK_DMA>;
+	};
+
+	tcu: timer@10002000 {
+		compatible = "ingenic,jz4725b-tcu", "simple-mfd";
+		reg = <0x10002000 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10002000 0x1000>;
+
+		#clock-cells = <1>;
+
+		clocks = <&cgu JZ4755_CLK_RTC>,
+			 <&cgu JZ4755_CLK_EXT>,
+			 <&cgu JZ4755_CLK_PCLK>,
+			 <&cgu JZ4755_CLK_TCU>;
+		clock-names = "rtc", "ext", "pclk", "tcu";
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <23>, <22>, <21>;
+
+		watchdog: watchdog@0 {
+			compatible = "ingenic,jz4725b-watchdog", "ingenic,jz4740-watchdog";
+			reg = <0x0 0xc>;
+
+			clocks = <&tcu TCU_CLK_WDT>;
+			clock-names = "wdt";
+		};
+
+		pwm: pwm@60 {
+			compatible = "ingenic,jz4725b-pwm";
+			reg = <0x60 0x40>;
+
+			#pwm-cells = <3>;
+
+			clocks = <&tcu TCU_CLK_TIMER0>, <&tcu TCU_CLK_TIMER1>,
+				 <&tcu TCU_CLK_TIMER2>, <&tcu TCU_CLK_TIMER3>,
+				 <&tcu TCU_CLK_TIMER4>, <&tcu TCU_CLK_TIMER5>;
+			clock-names = "timer0", "timer1", "timer2",
+				      "timer3", "timer4", "timer5";
+		};
+
+		ost: timer@e0 {
+			compatible = "ingenic,jz4725b-ost";
+			reg = <0xe0 0x20>;
+
+			clocks = <&tcu TCU_CLK_OST>;
+			clock-names = "ost";
+
+			interrupts = <15>;
+		};
+	};
+
+	aic: audio-controller@10020000 {
+		compatible = "ingenic,jz4725b-i2s", "ingenic,jz4740-i2s";
+		reg = <0x10020000 0x38>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4755_CLK_AIC>,
+			 <&cgu JZ4755_CLK_I2S>,
+			 <&cgu JZ4755_CLK_EXT>,
+			 <&cgu JZ4755_CLK_PLL_HALF>;
+		clock-names = "aic", "i2s", "ext", "pll half";
+
+		interrupt-parent = <&intc>;
+		interrupts = <10>;
+
+		dmas = <&dmac0 25 0xffffffff>, <&dmac0 24 0xffffffff>;
+		dma-names = "rx", "tx";
+	};
+
+	codec: audio-codec@100200a4 {
+		compatible = "ingenic,jz4725b-codec";
+		reg = <0x100200a4 0x8>;
+
+		#sound-dai-cells = <0>;
+
+		clocks = <&cgu JZ4755_CLK_AIC>;
+		clock-names = "aic";
+	};
+
+	adc: adc@10070000 {
+		compatible = "ingenic,jz4725b-adc";
+		#io-channel-cells = <1>;
+
+		reg = <0x10070000 0x30>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x10070000 0x30>;
+
+		clocks = <&cgu JZ4755_CLK_ADC>;
+		clock-names = "adc";
+
+		interrupt-parent = <&intc>;
+		interrupts = <18>;
+	};
+
+	nemc: memory-controller@13010000 {
+		compatible = "ingenic,jz4725b-nemc", "ingenic,jz4740-nemc";
+		reg = <0x13010000 0x10000>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0 0x18000000 0x4000000>, <2 0 0x14000000 0x4000000>,
+			 <3 0 0x0c000000 0x4000000>, <4 0 0x08000000 0x4000000>;
+
+		clocks = <&cgu JZ4755_CLK_MCLK>;
+	};
+
+	udc: usb@13040000 {
+		compatible = "ingenic,jz4725b-musb", "ingenic,jz4740-musb";
+		reg = <0x13040000 0x10000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <27>;
+		interrupt-names = "mc";
+
+		clocks = <&cgu JZ4755_CLK_UDC>;
+		clock-names = "udc";
+	};
+
+	lcd: lcd-controller@13050000 {
+		compatible = "ingenic,jz4725b-lcd";
+		reg = <0x13050000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <31>;
+
+		clocks = <&cgu JZ4755_CLK_LCD>;
+		clock-names = "lcd_pclk";
+
+		lcd_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@8 {
+				reg = <8>;
+
+				ipu_output: endpoint {
+					remote-endpoint = <&ipu_input>;
+				};
+			};
+		};
+	};
+
+	ipu: ipu@13080000 {
+		compatible = "ingenic,jz4725b-ipu";
+		reg = <0x13080000 0x64>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <30>;
+
+		clocks = <&cgu JZ4755_CLK_IPU>;
+		clock-names = "ipu";
+
+		port {
+			ipu_input: endpoint {
+				remote-endpoint = <&ipu_output>;
+			};
+		};
+	};
+
+	bch: ecc-controller@130d0000 {
+		compatible = "ingenic,jz4725b-bch";
+		reg = <0x130d0000 0x44>;
+
+		clocks = <&cgu JZ4755_CLK_BCH>;
+	};
+};