deleted file mode 100644
@@ -1,246 +0,0 @@
-Qualcomm Resource Power Manager (RPM)
-
-This driver is used to interface with the Resource Power Manager (RPM) found in
-various Qualcomm platforms. The RPM allows each component in the system to vote
-for state of the system resources, such as clocks, regulators and bus
-frequencies.
-
-Please refer to soc/qcom/qcom,ipc-rpm.yaml
-
-= SUBNODES
-
-The RPM exposes resources to its subnodes. The below bindings specify the set
-of valid subnodes that can operate on these resources.
-
-== Regulators
-
-Regulator nodes are identified by their compatible:
-
-- compatible:
- Usage: required
- Value type: <string>
- Definition: must be one of:
- "qcom,rpm-pm8058-regulators"
- "qcom,rpm-pm8901-regulators"
- "qcom,rpm-pm8921-regulators"
- "qcom,rpm-pm8018-regulators"
- "qcom,rpm-smb208-regulators"
-
-- vdd_l0_l1_lvs-supply:
-- vdd_l2_l11_l12-supply:
-- vdd_l3_l4_l5-supply:
-- vdd_l6_l7-supply:
-- vdd_l8-supply:
-- vdd_l9-supply:
-- vdd_l10-supply:
-- vdd_l13_l16-supply:
-- vdd_l14_l15-supply:
-- vdd_l17_l18-supply:
-- vdd_l19_l20-supply:
-- vdd_l21-supply:
-- vdd_l22-supply:
-- vdd_l23_l24_l25-supply:
-- vdd_ncp-supply:
-- vdd_s0-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
- Usage: optional (pm8058 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-- lvs0_in-supply:
-- lvs1_in-supply:
-- lvs2_in-supply:
-- lvs3_in-supply:
-- mvs_in-supply:
-- vdd_l0-supply:
-- vdd_l1-supply:
-- vdd_l2-supply:
-- vdd_l3-supply:
-- vdd_l4-supply:
-- vdd_l5-supply:
-- vdd_l6-supply:
-- vdd_s0-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
- Usage: optional (pm8901 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-- vdd_l1_l2_l12_l18-supply:
-- vdd_l3_l15_l17-supply:
-- vdd_l4_l14-supply:
-- vdd_l5_l8_l16-supply:
-- vdd_l6_l7-supply:
-- vdd_l9_l11-supply:
-- vdd_l10_l22-supply:
-- vdd_l21_l23_l29-supply:
-- vdd_l24-supply:
-- vdd_l25-supply:
-- vdd_l26-supply:
-- vdd_l27-supply:
-- vdd_l28-supply:
-- vdd_ncp-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-- vin_5vs-supply:
-- vin_lvs1_3_6-supply:
-- vin_lvs2-supply:
-- vin_lvs4_5_7-supply:
- Usage: optional (pm8921 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-- vin_lvs1-supply:
-- vdd_l7-supply:
-- vdd_l8-supply:
-- vdd_l9_l10_l11_l12-supply:
- Usage: optional (pm8018 only)
- Value type: <phandle>
- Definition: reference to regulator supplying the input pin, as
- described in the data sheet
-
-The regulator node houses sub-nodes for each regulator within the device. Each
-sub-node is identified using the node's name, with valid values listed for each
-of the pmics below.
-
-pm8058:
- l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
- l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
- lvs0, lvs1, ncp
-
-pm8901:
- l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
- mvs
-
-pm8921:
- s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
- l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
- l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
- ncp
-
-pm8018:
- s1, s2, s3, s4, s5, , l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
- l12, l14, lvs1
-
-smb208:
- s1a, s1b, s2a, s2b
-
-The content of each sub-node is defined by the standard binding for regulators -
-see regulator.txt - with additional custom properties described below:
-
-=== Switch-mode Power Supply regulator custom properties
-
-- bias-pull-down:
- Usage: optional
- Value type: <empty>
- Definition: enable pull down of the regulator when inactive
-
-- qcom,switch-mode-frequency:
- Usage: required
- Value type: <u32>
- Definition: Frequency (Hz) of the switch-mode power supply;
- must be one of:
- 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
- 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
- 1480000, 1370000, 1280000, 1200000
-
-- qcom,force-mode:
- Usage: optional (default if no other qcom,force-mode is specified)
- Value type: <u32>
- Definition: indicates that the regulator should be forced to a
- particular mode, valid values are:
- QCOM_RPM_FORCE_MODE_NONE - do not force any mode
- QCOM_RPM_FORCE_MODE_LPM - force into low power mode
- QCOM_RPM_FORCE_MODE_HPM - force into high power mode
- QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
- select its own mode based on
- realtime current draw, only for:
- pm8921 smps and ftsmps
-
-- qcom,power-mode-hysteretic:
- Usage: optional
- Value type: <empty>
- Definition: select that the power supply should operate in hysteretic
- mode, instead of the default pwm mode
-
-=== Low-dropout regulator custom properties
-
-- bias-pull-down:
- Usage: optional
- Value type: <empty>
- Definition: enable pull down of the regulator when inactive
-
-- qcom,force-mode:
- Usage: optional
- Value type: <u32>
- Definition: indicates that the regulator should not be forced to any
- particular mode, valid values are:
- QCOM_RPM_FORCE_MODE_NONE - do not force any mode
- QCOM_RPM_FORCE_MODE_LPM - force into low power mode
- QCOM_RPM_FORCE_MODE_HPM - force into high power mode
- QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
- mode, i.e. to act as a switch
- and not regulate, only for:
- pm8921 pldo, nldo and nldo1200
-
-=== Negative Charge Pump custom properties
-
-- qcom,switch-mode-frequency:
- Usage: required
- Value type: <u32>
- Definition: Frequency (Hz) of the switch mode power supply;
- must be one of:
- 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
- 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
- 1480000, 1370000, 1280000, 1200000
-
-= EXAMPLE
-
- #include <dt-bindings/mfd/qcom-rpm.h>
-
- rpm@108000 {
- compatible = "qcom,rpm-msm8960";
- reg = <0x108000 0x1000>;
- qcom,ipc = <&apcs 0x8 2>;
-
- interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
- interrupt-names = "ack", "err", "wakeup";
-
- regulators {
- compatible = "qcom,rpm-pm8921-regulators";
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-
- s1 {
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
-
- bias-pull-down;
-
- qcom,switch-mode-frequency = <3200000>;
- };
-
- pm8921_s4: s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
-
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
-
- qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
- };
- };
- };
-
new file mode 100644
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/qcom,ipc-rpm-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: QCOM IPC RPM REGULATOR
+
+description:
+ The Qualcomm RPM over IPC regulator is modelled as a subdevice of the RPM.
+
+ Please refer to Documentation/devicetree/bindings/soc/qcom/qcom,ipc-rpm.yaml
+ for information regarding the RPM node.
+
+ The regulator node houses sub-nodes for each regulator within the device.
+ Each sub-node is identified using the node's name, with valid values listed
+ for each of the pmics below.
+
+ For pm8058 l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
+ l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
+ lvs0, lvs1, ncp
+
+ For pm8901 l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
+ mvs
+
+ For pm8921 s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+ l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
+ l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
+ ncp
+
+ For pm8018 s1, s2, s3, s4, s5, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
+ l12, l14, lvs1
+
+ For smb208 s1a, s1b, s2a, s2b
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+
+properties:
+ compatible:
+ enum:
+ - qcom,rpm-pm8058-regulators
+ - qcom,rpm-pm8901-regulators
+ - qcom,rpm-pm8921-regulators
+ - qcom,rpm-pm8018-regulators
+ - qcom,rpm-smb208-regulators
+
+patternProperties:
+ ".*-supply$":
+ description: Input supply phandle(s) for this node
+
+ "^((s|l|lvs)[0-9]*)|(s[1-2][a-b])|(ncp)|(mvs)|(usb-switch)|(hdmi-switch)$":
+ description: List of regulators and its properties
+ $ref: regulator.yaml#
+ properties:
+ bias-pull-down:
+ description: enable pull down of the regulator when inactive
+ type: boolean
+
+ qcom,switch-mode-frequency:
+ description: Frequency (Hz) of the switch-mode power supply
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum:
+ - 19200000
+ - 9600000
+ - 6400000
+ - 4800000
+ - 3840000
+ - 3200000
+ - 2740000
+ - 2400000
+ - 2130000
+ - 1920000
+ - 1750000
+ - 1600000
+ - 1480000
+ - 1370000
+ - 1280000
+ - 1200000
+
+ qcom,force-mode:
+ description: Indicates that the regulator should be forced to a particular mode
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum:
+ - 0 # QCOM_RPM_FORCE_MODE_NONE do not force any mode
+ - 1 # QCOM_RPM_FORCE_MODE_LPM force into low power mode
+ - 2 # QCOM_RPM_FORCE_MODE_HPM force into high power mode
+ - 3 # QCOM_RPM_FORCE_MODE_AUTO allow regulator to automatically select its own mode
+ # based on realtime current draw, only for pm8921 smps and ftsmps
+
+ qcom,power-mode-hysteretic:
+ description: select that the power supply should operate in hysteretic mode,
+ instead of the default pwm mode
+ type: boolean
+
+additionalProperties: false
+
+required:
+ - compatible
+
+examples:
+ - |
+ #include <dt-bindings/mfd/qcom-rpm.h>
+ regulators {
+ compatible = "qcom,rpm-pm8921-regulators";
+ vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+
+ s1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+
+ bias-pull-down;
+
+ qcom,switch-mode-frequency = <3200000>;
+ };
+
+ pm8921_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ qcom,switch-mode-frequency = <1600000>;
+ bias-pull-down;
+
+ qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+ };
+ };
+...
Convert the non-SMD Regulators bindings to dt-schema and remove the old text based bindings now we have migrated all the content. Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> --- Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 246 --------------------- .../bindings/regulator/qcom,ipc-rpm-regulator.yaml | 127 +++++++++++ 2 files changed, 127 insertions(+), 246 deletions(-)