@@ -10,6 +10,7 @@
#include <linux/i2c.h>
#include <linux/rmi.h>
#include <linux/of.h>
+#include <linux/irq.h>
#include "rmi_driver.h"
#define BUFFER_SIZE_INCREMENT 32
@@ -188,7 +189,7 @@ static irqreturn_t rmi_i2c_irq(int irq, void *dev_id)
static int rmi_i2c_init_irq(struct i2c_client *client)
{
struct rmi_i2c_xport *rmi_i2c = i2c_get_clientdata(client);
- int irq_flags = rmi_i2c->xport.pdata.irq_flags;
+ int irq_flags = irqd_get_trigger_type(irq_get_irq_data(rmi_i2c->irq));
int ret;
if (!irq_flags)
@@ -342,7 +342,7 @@ static irqreturn_t rmi_spi_irq(int irq, void *dev_id)
static int rmi_spi_init_irq(struct spi_device *spi)
{
struct rmi_spi_xport *rmi_spi = spi_get_drvdata(spi);
- int irq_flags = rmi_spi->xport.pdata.irq_flags;
+ int irq_flags = irqd_get_trigger_type(irq_get_irq_data(rmi_i2c->irq));
int ret;
if (!irq_flags)
@@ -201,15 +201,11 @@ struct rmi_device_platform_data_spi {
/**
* struct rmi_device_platform_data - system specific configuration info.
*
- * @irq_flags - this is used to specify intrerrupt type flags.
- *
* @reset_delay_ms - after issuing a reset command to the touch sensor, the
* driver waits a few milliseconds to give the firmware a chance to
* to re-initialize. You can override the default wait period here.
*/
struct rmi_device_platform_data {
- int irq_flags;
-
int reset_delay_ms;
struct rmi_device_platform_data_spi spi_data;
I don't understand what the irq_flags in the platform data is there for other than being default 0. The trigger type is specified by device tree or ACPI or similar so before forcing it to LEVEL_LOW, ask the descriptor what flags it already have. Without this my RMI4 touchscreen fails like this: input: Synaptics TM1217 as /devices/rmi4-00/input/input2 genirq: Setting trigger mode 8 for irq 163 failed (nmk_gpio_irq_set_type+0x0/0x138) rmi4_i2c 3-004b: Failed to register interrupt 163 rmi4_i2c: probe of 3-004b failed with error -22 And that is because my GPIO controller does not support level IRQs, only edges. And that is also what is specified in the device tree: interrupts = <20 IRQ_TYPE_EDGE_FALLING>; but it is not falling through to the driver because of this hardcoding. This patch makes the driver respect the flags from the IRQ subsystem and only shoehorn it into LEVEL_LOW if none is specified. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- This goes on top of the v3 patchset and was necessary for my testing. Feel free to apply this on top of the RMI4 patches OR squash it into the series, I don't care as long as the result works for me. --- drivers/input/rmi4/rmi_i2c.c | 3 ++- drivers/input/rmi4/rmi_spi.c | 2 +- include/linux/rmi.h | 4 ---- 3 files changed, 3 insertions(+), 6 deletions(-) -- 2.4.3 -- To unsubscribe from this list: send the line "unsubscribe linux-input" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html