diff mbox series

[2/8] arm64: dts: qcom: sdm845-tama: Add Synaptics Touchscreen

Message ID 20220930191049.123256-3-konrad.dybcio@somainline.org
State New
Headers show
Series [1/8] arm64: dts: qcom: sdm845-tama: Add display nodes | expand

Commit Message

Konrad Dybcio Sept. 30, 2022, 7:10 p.m. UTC
Add required pins and RMI4 node to the common DT and remove it
from Akatsuki, as it uses a different touch.

Since the panels are super high tech proprietary incell, they
need to be handled with very precise timings. As such the panel
driver sets up the power rails and GPIOs and the touchscreen
driver *has to* probe afterwards.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 .../qcom/sdm845-sony-xperia-tama-akatsuki.dts |  3 +
 .../dts/qcom/sdm845-sony-xperia-tama.dtsi     | 69 ++++++++++++++++++-
 2 files changed, 70 insertions(+), 2 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts
index 2a16305ac5da..5c5949a51184 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts
@@ -7,6 +7,9 @@ 
 
 #include "sdm845-sony-xperia-tama.dtsi"
 
+/* XZ3 uses an Atmel touchscreen instead. */
+/delete-node/ &touchscreen;
+
 / {
 	model = "Sony Xperia XZ3";
 	compatible = "sony,akatsuki-row", "qcom,sdm845";
diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
index ac8eb59ed010..809a6d7e739b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
@@ -375,10 +375,43 @@  &gcc {
 };
 
 &i2c5 {
-	status = "okay";
 	clock-frequency = <400000>;
+	status = "okay";
+
+	touchscreen: touchscreen@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&vreg_l14a_1p8>;
+		/*
+		 * This is a blatant abuse of OF, but the panel driver *needs*
+		 * to probe first, as the power/gpio switching needs to be precisely
+		 * timed in order for both the display and touch panel to function properly.
+		 */
+		incell-supply = <&panel>;
+
+		syna,reset-delay-ms = <220>;
+		syna,startup-delay-ms = <1000>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ts_default>;
+		pinctrl-1 = <&ts_sleep>;
 
-	/* Synaptics touchscreen @ 2c, 3c */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x01>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
 };
 
 &i2c10 {
@@ -497,6 +530,38 @@  sde_te_active_sleep: sde-te-active-sleep-state {
 		drive-strength = <2>;
 		bias-pull-down;
 	};
+
+	ts_default: ts-default-state {
+		reset-pin {
+			pins = "gpio99";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		int-pin {
+			pins = "gpio125";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	ts_sleep: ts-sleep-state {
+		reset-pin {
+			pins = "gpio99";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		int-pin {
+			pins = "gpio125";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
 };
 
 &uart6 {