@@ -12,6 +12,7 @@
#include <linux/phy.h>
#include <linux/polynomial.h>
#include <linux/netdevice.h>
+#include <linux/of_platform.h>
/* PHY ID */
#define PHY_ID_GPYx15B_MASK 0xFFFFFFFC
@@ -32,6 +33,7 @@
#define PHY_MIISTAT 0x18 /* MII state */
#define PHY_IMASK 0x19 /* interrupt mask */
#define PHY_ISTAT 0x1A /* interrupt status */
+#define PHY_LED 0x1B /* LED control */
#define PHY_FWV 0x1E /* firmware version */
#define PHY_MIISTAT_SPD_MASK GENMASK(2, 0)
@@ -59,6 +61,16 @@
#define PHY_FWV_MAJOR_MASK GENMASK(11, 8)
#define PHY_FWV_MINOR_MASK GENMASK(7, 0)
+/* LED */
+#define VSPEC1_LED0_CTRL 0x01
+#define VSPEC1_LED1_CTRL 0x02
+#define VSPEC1_LED2_CTRL 0x03
+#define VSPEC1_LED3_CTRL 0x04
+#define TWO_LED_CONFIG 0x0300
+#define LED_BLINK_2500MBIT 0x0380
+#define LED_BLINK_1000MBIT_100MBIT_10_MBIT 0x0370
+#define LED_DUAL_MODE 2
+
/* SGMII */
#define VSPEC1_SGMII_CTRL 0x08
#define VSPEC1_SGMII_CTRL_ANEN BIT(12) /* Aneg enable */
@@ -201,9 +213,34 @@ static int gpy_config_init(struct phy_device *phydev)
return ret < 0 ? ret : 0;
}
+static int gpy_override_led_mode(struct phy_device
+ *phydev, u32 led_mode)
+{
+ int ret;
+
+ if (led_mode == LED_DUAL_MODE) {
+ ret = phy_write(phydev, PHY_LED, TWO_LED_CONFIG);
+ if (ret < 0)
+ return ret;
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
+ VSPEC1_LED0_CTRL,
+ LED_BLINK_2500MBIT);
+ if (ret < 0)
+ return ret;
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
+ VSPEC1_LED1_CTRL,
+ LED_BLINK_1000MBIT_100MBIT_10_MBIT);
+ if (ret < 0)
+ return ret;
+ }
+
+ return 0;
+}
+
static int gpy_probe(struct phy_device *phydev)
{
struct device *dev = &phydev->mdio.dev;
+ struct device_node *np = dev->of_node;
struct gpy_priv *priv;
int fw_version;
int ret;
@@ -234,6 +271,14 @@ static int gpy_probe(struct phy_device *phydev)
priv->fw_major, priv->fw_minor, fw_version,
fw_version & PHY_FWV_REL_MASK ? "" : " test version");
+ /* Override led mode */
+ ret = of_property_read_bool(np, "mxl,dual-led-mode");
+ if (ret) {
+ ret = gpy_override_led_mode(phydev, LED_DUAL_MODE);
+ if (ret < 0)
+ return ret;
+ }
+
return 0;
}
GPY211 phy default to using all four led pins. Hardwares using only two leds where led0 is used as the high network speed led and led1 the low network speed led will not get the correct behaviour since 1Gbit and 2.5Gbit will not be represented at all in the existing leds. This patch adds a property for switching to a two led mode as specified above. Signed-off-by: Marcus Carlberg <marcus.carlberg@axis.com> --- drivers/net/phy/mxl-gpy.c | 45 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+) -- 2.20.1