@@ -8042,6 +8042,12 @@ S: Maintained
F: Documentation/ABI/testing/sysfs-driver-intel-m10-bmc-sec-update
F: drivers/fpga/intel-m10-bmc-sec-update.c
+MICROCHIP EMC230X PWM-FAN CONTROLLER DRIVERS
+M: Mathew McBride <matt@traverse.com.au>
+L: linux-hwmon@vger.kernel.org
+S: Maintained
+F: drivers/hwmon/emc230x.c
+
MICROCHIP POLARFIRE FPGA DRIVERS
M: Conor Dooley <conor.dooley@microchip.com>
R: Ivan Bornyakov <i.bornyakov@metrotek.ru>
@@ -1775,6 +1775,19 @@ config SENSORS_EMC1403
Threshold values can be configured using sysfs.
Data from the different diodes are accessible via sysfs.
+config SENSORS_EMC230X
+ tristate "Microchip EMC230X fan controllers"
+ depends on I2C
+ help
+ If you say yes here you get support for the Microchip (SMSC)
+ EMC230x family of RPM-PWM fan controllers.
+
+ When the thermal subsystem is enabled, this driver can
+ be used as a cooling-device for a thermal zone.
+
+ This driver can also be built as a module. If so, the module
+ will be called emc230x.
+
config SENSORS_EMC2103
tristate "SMSC EMC2103"
depends on I2C
@@ -69,6 +69,7 @@ obj-$(CONFIG_SENSORS_DRIVETEMP) += drivetemp.o
obj-$(CONFIG_SENSORS_DS620) += ds620.o
obj-$(CONFIG_SENSORS_DS1621) += ds1621.o
obj-$(CONFIG_SENSORS_EMC1403) += emc1403.o
+obj-$(CONFIG_SENSORS_EMC230X) += emc230x.o
obj-$(CONFIG_SENSORS_EMC2103) += emc2103.o
obj-$(CONFIG_SENSORS_EMC6W201) += emc6w201.o
obj-$(CONFIG_SENSORS_F71805F) += f71805f.o
new file mode 100644
@@ -0,0 +1,587 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Microchip (formerly SMSC) EMC230X family RPM fan controller driver
+ * For EMC2301/2/5 controllers
+ * Copyright (C) 2021-2022 Traverse Technologies
+ */
+
+/*
+ * This driver has two components:
+ * - hwmon (read/write fan rpm values)
+ * - thermal (set fan rpm speeds for cooling purposes)
+ */
+
+#include <linux/err.h>
+#include <linux/hwmon.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+
+#define TACH_HIGH_MASK GENMASK(12, 5)
+#define TACH_LOW_MASK GENMASK(4, 0)
+
+#define EMC230X_FAN_STALL_STATUS_REG 0x25
+#define EMC230X_FAN_SPIN_FAIL_STATUS_REG 0x26
+#define EMC230X_FAN_DRIVE_FAIL_STATUS_REG 0x27
+
+#define EMC230X_PWM_FAN_DRIVE_REG(channel) (0x30 + (channel * 0x10))
+#define EMC230X_FAN_CONFIG_REG(channel) (0x32 + (channel * 0x10))
+#define EMC230X_FAN_CONFIG_ENABLE_CLOSED_LOOP BIT(7)
+#define EMC230X_TACH_TARGET_LOW_REG(channel) (0x3C + (channel * 0x10))
+#define EMC230X_TACH_READ_HIGH_REG(channel) (0x3E + (channel * 0x10))
+
+#define THERMAL_DEVICE_COOLING_MAX_STEPS 7
+#define MAX_COOLING_DEV_NAME_LEN 16
+/*
+ * Factor by equations [2] and [3] from data sheet; valid for fans where the
+ * number of edges equals (poles * 2 + 1).
+ */
+#define FAN_RPM_FACTOR 3932160
+
+struct emc230x_cooling_device {
+ struct emc230x_data *parent;
+ char name[MAX_COOLING_DEV_NAME_LEN];
+ struct thermal_cooling_device *tcdev;
+ u8 channel;
+ u8 cur_state;
+ u16 cooling_step;
+ u16 min_rpm;
+ u16 max_rpm;
+};
+
+struct emc230x_data {
+ struct device *hwmon_dev;
+ struct i2c_client *i2c_client;
+ u8 device_max_channels;
+};
+
+static const struct i2c_device_id emc230x_ids[] = {
+ { "emc2301", 1 },
+ { "emc2302", 2 },
+ { "emc2303", 3 },
+ { "emc2305", 5 },
+ { /* sentinel */ }
+};
+
+MODULE_DEVICE_TABLE(i2c, emc230x_ids);
+
+static int emc2301_read_fan_tach(struct device *dev,
+ int channel,
+ u16 *tach)
+{
+ struct emc230x_data *priv = dev_get_drvdata(dev);
+ u8 channel_high_register_addr;
+ u16 combined_reading;
+ u8 channel_bytes[2];
+ int bytes_read;
+
+ if ((channel + 1) > priv->device_max_channels)
+ return -EINVAL;
+
+ channel_high_register_addr = EMC230X_TACH_READ_HIGH_REG(channel);
+
+ bytes_read = i2c_smbus_read_i2c_block_data(priv->i2c_client,
+ channel_high_register_addr,
+ 2, &channel_bytes[0]);
+ if (bytes_read < 2) {
+ dev_err(dev,
+ "%s: error %d reading channel %d tach register",
+ __func__, bytes_read, channel);
+ return bytes_read;
+ }
+
+ /* First byte (register) is the high byte, second low byte */
+ combined_reading = ((u16)(channel_bytes[0]) << 5) | (channel_bytes[1] >> 3);
+
+ *tach = combined_reading;
+
+ return 0;
+}
+
+static int emc230x_show_fan_rpm(struct device *dev, int channel, long *val)
+{
+ long fan_rpm;
+ u16 channel_tach;
+ int ret;
+
+ ret = emc2301_read_fan_tach(dev, channel, &channel_tach);
+ if (ret)
+ return ret;
+
+ fan_rpm = (FAN_RPM_FACTOR * 2) / channel_tach;
+ *val = fan_rpm;
+
+ return 0;
+}
+
+static int emc230x_write_fan_rpm_target(struct i2c_client *client,
+ int channel, long target_rpm)
+{
+ int ret;
+ u16 target_tach;
+ u8 tach_channel_reg_addr;
+ u8 tach_bytes[2];
+
+ tach_channel_reg_addr = EMC230X_TACH_TARGET_LOW_REG(channel);
+ /* 0 RPM is a special case - writing 0xFFF0 will turn off the fan */
+ if (target_rpm == 0) {
+ tach_bytes[0] = 0xF0;
+ tach_bytes[1] = 0xFF;
+ } else {
+ target_tach = (FAN_RPM_FACTOR * 2) / target_rpm;
+ tach_bytes[0] = (target_tach & TACH_LOW_MASK) << 3;
+ tach_bytes[1] = (target_tach & TACH_HIGH_MASK) >> 5;
+ }
+
+ ret = i2c_smbus_write_i2c_block_data(client,
+ tach_channel_reg_addr,
+ 2, &tach_bytes[0]);
+ if (ret != 2)
+ return ret;
+
+ return 0;
+}
+
+static int emc230x_set_fan_rpm(struct device *dev, int channel, long target_rpm)
+{
+ struct emc230x_data *priv = dev_get_drvdata(dev);
+
+ if ((channel + 1) > priv->device_max_channels)
+ return -ENODEV;
+
+ dev_dbg(dev,
+ "%s: setting channel %d rpm to %ld\n",
+ __func__, channel, target_rpm);
+
+ return emc230x_write_fan_rpm_target(priv->i2c_client, channel, target_rpm);
+}
+
+static int emc230x_read_fan_rpm_target_value(struct i2c_client *client,
+ int channel,
+ long *target_rpm_value)
+{
+ int ret;
+ u8 tach_channel_reg_addr;
+ u8 tach_bytes[2];
+ u16 combined_reading;
+ long rpm_target;
+
+ tach_channel_reg_addr = EMC230X_TACH_TARGET_LOW_REG(channel);
+ ret = i2c_smbus_read_i2c_block_data(client,
+ tach_channel_reg_addr,
+ 2, &tach_bytes[0]);
+ if (ret != 2)
+ return ret;
+
+ /* This is different from the RPM speed registers,
+ * the low byte is the first register read
+ */
+ if (tach_bytes[1] == 0xFF && tach_bytes[0] == 0xF0) {
+ rpm_target = 0;
+ } else {
+ combined_reading = ((u16)(tach_bytes[1]) << 5) | (tach_bytes[0] >> 3);
+ rpm_target = (FAN_RPM_FACTOR * 2) / combined_reading;
+ }
+
+ *target_rpm_value = rpm_target;
+ return 0;
+}
+
+static int emc230x_show_fan_rpm_target(struct device *dev, int channel,
+ long *value)
+{
+ struct emc230x_data *priv = dev_get_drvdata(dev);
+
+ if ((channel + 1) > priv->device_max_channels)
+ return -EINVAL;
+
+ return emc230x_read_fan_rpm_target_value(priv->i2c_client,
+ channel,
+ value);
+}
+
+static int emc230x_enable_rpm_control(struct device *dev,
+ struct i2c_client *client,
+ int channel, bool enable)
+{
+ u8 fan_config_reg_addr;
+ u8 fan_config_reg_val;
+ int ret;
+
+ fan_config_reg_addr = EMC230X_FAN_CONFIG_REG(channel);
+
+ fan_config_reg_val = i2c_smbus_read_byte_data(client, fan_config_reg_addr);
+ if (enable)
+ fan_config_reg_val |= EMC230X_FAN_CONFIG_ENABLE_CLOSED_LOOP;
+ else
+ fan_config_reg_val &= ~(EMC230X_FAN_CONFIG_ENABLE_CLOSED_LOOP);
+
+ ret = i2c_smbus_write_byte_data(client, fan_config_reg_addr, fan_config_reg_val);
+ if (ret) {
+ dev_err(dev,
+ "Unable to write fan configuration register %02X\n",
+ fan_config_reg_addr);
+ return ret;
+ }
+
+ /* If RPM drive not enabled, set PWM cycle (non-closed loop) to 100% */
+ if (!enable)
+ ret = i2c_smbus_write_byte_data(client,
+ EMC230X_PWM_FAN_DRIVE_REG(channel),
+ 0xFF);
+
+ return ret;
+};
+
+static int emc230x_write_rpm_control(struct device *dev,
+ int channel,
+ long value)
+{
+ struct emc230x_data *priv = dev_get_drvdata(dev);
+ bool enable_rpm_control = (value == 1) ? true : false;
+
+ return emc230x_enable_rpm_control(dev, priv->i2c_client,
+ channel,
+ enable_rpm_control);
+}
+
+static int emc230x_read_is_rpm_control(struct device *dev,
+ int channel,
+ long *value)
+{
+ struct emc230x_data *priv = dev_get_drvdata(dev);
+ u8 fan_config_reg_addr;
+ u32 fan_config_reg_val;
+
+ fan_config_reg_addr = EMC230X_FAN_CONFIG_REG(channel);
+
+ fan_config_reg_val = i2c_smbus_read_byte_data(priv->i2c_client,
+ fan_config_reg_addr);
+ if (fan_config_reg_val < 0)
+ return fan_config_reg_val;
+
+ if (fan_config_reg_val & EMC230X_FAN_CONFIG_ENABLE_CLOSED_LOOP)
+ *value = 1;
+ else
+ *value = 0;
+
+ return 0;
+}
+
+
+static int emc230x_read_fault(struct i2c_client *client,
+ int channel,
+ long *retval)
+{
+ int ret;
+ u8 fan_mask;
+ u8 fan_status_registers[3];
+ long fault_value = 0;
+
+ /* Read the three fan fault registers (stall,spin,drive)
+ * consecutively
+ */
+ ret = i2c_smbus_read_i2c_block_data(client,
+ EMC230X_FAN_STALL_STATUS_REG,
+ 3, &fan_status_registers[0]);
+ if (ret != 3)
+ return ret;
+
+ fan_mask = (1 << channel);
+
+ if (fan_status_registers[0] & fan_mask) /* Stall */
+ fault_value = 1;
+ if (fan_status_registers[1] & fan_mask) /* Spin */
+ fault_value |= (1<<1);
+ if (fan_status_registers[2] & fan_mask) /* Drive */
+ fault_value |= (1<<2);
+ *retval = fault_value;
+
+ return 0;
+}
+
+static int emc230x_show_faults(struct device *dev, int channel,
+ long *value)
+{
+ struct emc230x_data *priv = dev_get_drvdata(dev);
+
+ return emc230x_read_fault(priv->i2c_client, channel, value);
+}
+
+static const struct hwmon_channel_info *emc2301_hwmon_info[] = {
+ HWMON_CHANNEL_INFO(fan,
+ HWMON_F_INPUT | HWMON_F_FAULT | HWMON_F_TARGET,
+ HWMON_F_INPUT | HWMON_F_FAULT | HWMON_F_TARGET,
+ HWMON_F_INPUT | HWMON_F_FAULT | HWMON_F_TARGET,
+ HWMON_F_INPUT | HWMON_F_FAULT | HWMON_F_TARGET,
+ HWMON_F_INPUT | HWMON_F_FAULT | HWMON_F_TARGET),
+ HWMON_CHANNEL_INFO(pwm,
+ HWMON_PWM_ENABLE,
+ HWMON_PWM_ENABLE,
+ HWMON_PWM_ENABLE,
+ HWMON_PWM_ENABLE,
+ HWMON_PWM_ENABLE),
+ NULL
+};
+
+static umode_t emc230x_hwmon_is_visible(const void *data,
+ enum hwmon_sensor_types type,
+ u32 attr, int channel)
+{
+ struct emc230x_data *priv = (struct emc230x_data *)data;
+
+ if ((channel + 1) > priv->device_max_channels)
+ return 0;
+
+ switch (type) {
+ case hwmon_fan:
+ switch (attr) {
+ case hwmon_fan_input:
+ case hwmon_fan_fault:
+ return 0444;
+ case hwmon_fan_target:
+ return 0644;
+ default:
+ return 0;
+ }
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_enable:
+ return 0644;
+ default:
+ return 0;
+ }
+ default:
+ return 0;
+ }
+}
+
+static int emc230x_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long *value)
+{
+ switch (type) {
+ case hwmon_fan:
+ switch (attr) {
+ case hwmon_fan_input:
+ return emc230x_show_fan_rpm(dev, channel, value);
+ case hwmon_fan_target:
+ return emc230x_show_fan_rpm_target(dev, channel, value);
+ case hwmon_fan_fault:
+ return emc230x_show_faults(dev, channel, value);
+ default:
+ return 0;
+ }
+ case hwmon_pwm:
+ switch (attr) {
+ case hwmon_pwm_enable:
+ return emc230x_read_is_rpm_control(dev, channel, value);
+ default:
+ return 0;
+ }
+ default:
+ return 0;
+ }
+}
+
+static int emc230x_hwmon_write(struct device *dev, enum hwmon_sensor_types type,
+ u32 attr, int channel, long value)
+{
+ if (type == hwmon_fan && attr == hwmon_fan_target)
+ return emc230x_set_fan_rpm(dev, channel, value);
+ else if (type == hwmon_pwm && attr == hwmon_pwm_enable)
+ return emc230x_write_rpm_control(dev, channel, value);
+
+ return -EINVAL;
+}
+
+static int emc230x_thermal_get_max_state(struct thermal_cooling_device *tcdev,
+ unsigned long *state)
+{
+ *state = THERMAL_DEVICE_COOLING_MAX_STEPS;
+ return 0;
+}
+
+static int emc230x_thermal_get_cur_state(struct thermal_cooling_device *tcdev,
+ unsigned long *state)
+{
+ struct emc230x_cooling_device *cdev = tcdev->devdata;
+
+ *state = cdev->cur_state;
+
+ return 0;
+}
+
+static int emc230x_thermal_set_cur_state(struct thermal_cooling_device *tcdev,
+ unsigned long state)
+{
+ struct emc230x_cooling_device *cdev = tcdev->devdata;
+ struct emc230x_data *parent_device = cdev->parent;
+ struct i2c_client *client = parent_device->i2c_client;
+ int ret;
+ u16 fan_rpm;
+
+ if (state > 0)
+ fan_rpm = cdev->min_rpm + ((state + 1) * cdev->cooling_step);
+ else
+ fan_rpm = cdev->min_rpm;
+
+ ret = emc230x_write_fan_rpm_target(client, cdev->channel, fan_rpm);
+ if (!ret)
+ cdev->cur_state = state;
+
+ return ret;
+}
+
+static const struct thermal_cooling_device_ops emc230x_fan_cooling_ops = {
+ .get_max_state = emc230x_thermal_get_max_state,
+ .get_cur_state = emc230x_thermal_get_cur_state,
+ .set_cur_state = emc230x_thermal_set_cur_state
+};
+
+/*
+ * emc230x_create_fan() - create a thermal device from FDT configuration
+ */
+static int emc230x_create_fan(struct device *dev,
+ struct device_node *child,
+ struct emc230x_data *priv)
+{
+ int ret;
+ u32 channel;
+ u16 min_rpm, max_rpm, cooling_range;
+ struct emc230x_cooling_device *faninfo;
+
+ ret = of_property_read_u32(child, "reg", &channel);
+ if (ret)
+ return ret;
+
+ if ((channel + 1) > priv->device_max_channels)
+ return -EINVAL;
+
+ /* If there are any DT attributes introduced that are not
+ * directly related to thermal subsystem integration
+ * (such as configuring PWM modes, or fan pole settings),
+ * they should be processed here before the #cooling-cells
+ * check
+ */
+ ret = of_property_count_u32_elems(child, "#cooling-cells");
+ if (ret < 1)
+ return 0;
+
+ ret = of_property_read_u16(child, "min-rpm", &min_rpm);
+ if (ret) {
+ dev_err(dev,
+ "%s: missing or invalid \"min-rpm\" property (channel=%d,err=%d)\n",
+ __func__, channel, ret);
+ return ret;
+ }
+
+ ret = of_property_read_u16(child, "max-rpm", &max_rpm);
+ if (ret) {
+ dev_err(dev,
+ "%s: missing or invalid \"min-rpm\" property (channel=%d,err=%d)\n",
+ __func__, channel, ret);
+ return ret;
+ }
+
+ faninfo = devm_kzalloc(dev, sizeof(*faninfo), GFP_KERNEL);
+
+ faninfo->parent = priv;
+ faninfo->channel = (u8)channel;
+ faninfo->min_rpm = min_rpm;
+ faninfo->max_rpm = max_rpm;
+
+ cooling_range = max_rpm - min_rpm;
+ faninfo->cooling_step = cooling_range / (THERMAL_DEVICE_COOLING_MAX_STEPS+1);
+ faninfo->cur_state = THERMAL_DEVICE_COOLING_MAX_STEPS;
+
+ /* Set the maximum fan rpm */
+ ret = emc230x_write_fan_rpm_target(priv->i2c_client, channel, max_rpm);
+ if (ret)
+ return ret;
+
+ /* Enable RPM closed-loop control */
+ ret = emc230x_enable_rpm_control(dev, priv->i2c_client, channel, true);
+ if (ret)
+ return ret;
+
+ snprintf(faninfo->name, MAX_COOLING_DEV_NAME_LEN, "%pOFn%d", child, channel);
+
+ faninfo->tcdev = devm_thermal_of_cooling_device_register(dev, child,
+ faninfo->name,
+ faninfo,
+ &emc230x_fan_cooling_ops);
+ dev_info(dev,
+ "channel %d registered as cooling device %d, min/max RPM %d/%d step %d\n",
+ channel, faninfo->tcdev->id, min_rpm, max_rpm, faninfo->cooling_step);
+
+ return 0;
+}
+
+static const struct hwmon_ops emc230x_hwmon_ops = {
+ .is_visible = emc230x_hwmon_is_visible,
+ .read = emc230x_hwmon_read,
+ .write = emc230x_hwmon_write,
+};
+
+static const struct hwmon_chip_info emc230x_chip_info = {
+ .ops = &emc230x_hwmon_ops,
+ .info = emc2301_hwmon_info
+};
+
+static int emc230x_probe(struct i2c_client *i2c)
+{
+ struct device *dev = &i2c->dev;
+ struct device *hwmon_dev;
+ struct device_node *np, *child;
+ struct emc230x_data *priv;
+ const struct i2c_device_id *dev_id;
+ int ret;
+
+ if (!i2c_check_functionality(i2c->adapter, I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA))
+ return -ENODEV;
+
+ priv = devm_kzalloc(dev, sizeof(struct emc230x_data), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->i2c_client = i2c;
+
+ dev_id = i2c_match_id(emc230x_ids, i2c);
+ if (!dev_id)
+ return -ENODEV;
+
+ priv->device_max_channels = (u32)dev_id->driver_data;
+
+ if (IS_REACHABLE(CONFIG_THERMAL) && dev->of_node) {
+ np = dev->of_node;
+ for_each_child_of_node(np, child) {
+ ret = emc230x_create_fan(dev, child, priv);
+ if (ret)
+ of_node_put(child);
+ }
+ }
+
+ hwmon_dev = devm_hwmon_device_register_with_info(dev, i2c->name,
+ priv,
+ &emc230x_chip_info,
+ NULL);
+ return PTR_ERR_OR_ZERO(hwmon_dev);
+}
+
+static struct i2c_driver emc230x_driver = {
+ .class = I2C_CLASS_HWMON,
+ .driver = {
+ .name = "emc230x",
+ },
+ .probe_new = emc230x_probe,
+ .id_table = emc230x_ids,
+};
+
+module_i2c_driver(emc230x_driver);
+
+MODULE_AUTHOR("Mathew McBride <matt@traverse.com.au>");
+MODULE_DESCRIPTION("Microchip EMC230X family PWM RPM fan controller driver");
+MODULE_LICENSE("GPL");
The EMC230X is a family of RPM-based RPM fan controllers from Microchip (and SMSC before that) available in 1 (EMC2301), 2, 3 and 5 (EMC2305) channel variants. This driver supports being used as a thermal cooling device, with RPM control when configured from a device tree. At the moment this driver assumes the 'default' PWM configuration in the controller (open-drain, 20kHz PWM), other configurations will require further development. Signed-off-by: Mathew McBride <matt@traverse.com.au> --- MAINTAINERS | 6 + drivers/hwmon/Kconfig | 13 + drivers/hwmon/Makefile | 1 + drivers/hwmon/emc230x.c | 587 ++++++++++++++++++++++++++++++++++++++++ 4 files changed, 607 insertions(+) create mode 100644 drivers/hwmon/emc230x.c