@@ -72,8 +72,7 @@ struct ftdi_private {
unsigned long last_dtr_rts; /* saved modem control outputs */
char prev_status; /* Used for TIOCMIWAIT */
char transmit_empty; /* If transmitter is empty or not */
- u16 interface; /* FT2232C, FT2232H or FT4232H port interface
- (0 for FT232/245) */
+ u16 channel; /* channel index, or 0 for legacy types */
speed_t force_baud; /* if non-zero, force the baud rate to
this value */
@@ -1271,7 +1270,7 @@ static int update_mctrl(struct usb_serial_port *port, unsigned int set,
usb_sndctrlpipe(port->serial->dev, 0),
FTDI_SIO_SET_MODEM_CTRL_REQUEST,
FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE,
- value, priv->interface,
+ value, priv->channel,
NULL, 0, WDR_TIMEOUT);
if (rv < 0) {
dev_dbg(dev, "%s Error from MODEM_CTRL urb: DTR %s, RTS %s\n",
@@ -1413,7 +1412,7 @@ static int change_speed(struct tty_struct *tty, struct usb_serial_port *port)
priv->chip_type == FTX) {
/* Probably the BM type needs the MSB of the encoded fractional
* divider also moved like for the chips above. Any infos? */
- index = (u16)((index << 8) | priv->interface);
+ index = (u16)((index << 8) | priv->channel);
}
rv = usb_control_msg(port->serial->dev,
@@ -1444,7 +1443,7 @@ static int write_latency_timer(struct usb_serial_port *port)
usb_sndctrlpipe(udev, 0),
FTDI_SIO_SET_LATENCY_TIMER_REQUEST,
FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE,
- l, priv->interface,
+ l, priv->channel,
NULL, 0, WDR_TIMEOUT);
if (rv < 0)
dev_err(&port->dev, "Unable to write latency timer: %i\n", rv);
@@ -1460,7 +1459,7 @@ static int _read_latency_timer(struct usb_serial_port *port)
rv = usb_control_msg_recv(udev, 0, FTDI_SIO_GET_LATENCY_TIMER_REQUEST,
FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE, 0,
- priv->interface, &buf, 1, WDR_TIMEOUT,
+ priv->channel, &buf, 1, WDR_TIMEOUT,
GFP_KERNEL);
if (rv == 0)
rv = buf;
@@ -1581,15 +1580,14 @@ static void ftdi_determine_type(struct usb_serial_port *port)
} else
priv->chip_type = FT2232C;
- /* Determine interface code. */
if (ifnum == 0)
- priv->interface = INTERFACE_A;
+ priv->channel = CHANNEL_A;
else if (ifnum == 1)
- priv->interface = INTERFACE_B;
+ priv->channel = CHANNEL_B;
else if (ifnum == 2)
- priv->interface = INTERFACE_C;
+ priv->channel = CHANNEL_C;
else if (ifnum == 3)
- priv->interface = INTERFACE_D;
+ priv->channel = CHANNEL_D;
/* BM-type devices have a bug where bcdDevice gets set
* to 0x200 when iSerialNumber is 0. */
@@ -1730,7 +1728,7 @@ static ssize_t event_char_store(struct device *dev,
usb_sndctrlpipe(udev, 0),
FTDI_SIO_SET_EVENT_CHAR_REQUEST,
FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE,
- v, priv->interface,
+ v, priv->channel,
NULL, 0, WDR_TIMEOUT);
if (rv < 0) {
dev_dbg(&port->dev, "Unable to write event character: %i\n", rv);
@@ -1804,7 +1802,7 @@ static int ftdi_set_bitmode(struct usb_serial_port *port, u8 mode)
usb_sndctrlpipe(serial->dev, 0),
FTDI_SIO_SET_BITMODE_REQUEST,
FTDI_SIO_SET_BITMODE_REQUEST_TYPE, val,
- priv->interface, NULL, 0, WDR_TIMEOUT);
+ priv->channel, NULL, 0, WDR_TIMEOUT);
if (result < 0) {
dev_err(&serial->interface->dev,
"bitmode request failed for value 0x%04x: %d\n",
@@ -1868,7 +1866,7 @@ static int ftdi_read_cbus_pins(struct usb_serial_port *port)
result = usb_control_msg_recv(serial->dev, 0,
FTDI_SIO_READ_PINS_REQUEST,
FTDI_SIO_READ_PINS_REQUEST_TYPE, 0,
- priv->interface, &buf, 1, WDR_TIMEOUT,
+ priv->channel, &buf, 1, WDR_TIMEOUT,
GFP_KERNEL);
if (result == 0)
result = buf;
@@ -2404,7 +2402,7 @@ static int ftdi_open(struct tty_struct *tty, struct usb_serial_port *port)
usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
FTDI_SIO_RESET_REQUEST, FTDI_SIO_RESET_REQUEST_TYPE,
FTDI_SIO_RESET_SIO,
- priv->interface, NULL, 0, WDR_TIMEOUT);
+ priv->channel, NULL, 0, WDR_TIMEOUT);
/* Termios defaults are set by usb_serial_init. We don't change
port->tty->termios - this would lose speed settings, etc.
@@ -2427,7 +2425,7 @@ static void ftdi_dtr_rts(struct usb_serial_port *port, int on)
usb_sndctrlpipe(port->serial->dev, 0),
FTDI_SIO_SET_FLOW_CTRL_REQUEST,
FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
- 0, priv->interface, NULL, 0,
+ 0, priv->channel, NULL, 0,
WDR_TIMEOUT) < 0) {
dev_err(&port->dev, "error from flowcontrol urb\n");
}
@@ -2620,7 +2618,7 @@ static void ftdi_break_ctl(struct tty_struct *tty, int break_state)
usb_sndctrlpipe(port->serial->dev, 0),
FTDI_SIO_SET_DATA_REQUEST,
FTDI_SIO_SET_DATA_REQUEST_TYPE,
- value , priv->interface,
+ value, priv->channel,
NULL, 0, WDR_TIMEOUT) < 0) {
dev_err(&port->dev, "%s FAILED to enable/disable break state (state was %d)\n",
__func__, break_state);
@@ -2756,7 +2754,7 @@ static void ftdi_set_termios(struct tty_struct *tty,
if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
FTDI_SIO_SET_DATA_REQUEST,
FTDI_SIO_SET_DATA_REQUEST_TYPE,
- value , priv->interface,
+ value, priv->channel,
NULL, 0, WDR_SHORT_TIMEOUT) < 0) {
dev_err(ddev, "%s FAILED to set databits/stopbits/parity\n",
__func__);
@@ -2769,7 +2767,7 @@ static void ftdi_set_termios(struct tty_struct *tty,
if (usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
FTDI_SIO_SET_FLOW_CTRL_REQUEST,
FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE,
- 0, priv->interface,
+ 0, priv->channel,
NULL, 0, WDR_TIMEOUT) < 0) {
dev_err(ddev, "%s error from disable flowcontrol urb\n",
__func__);
@@ -2803,7 +2801,7 @@ static void ftdi_set_termios(struct tty_struct *tty,
index = FTDI_SIO_DISABLE_FLOW_CTRL;
}
- index |= priv->interface;
+ index |= priv->channel;
ret = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
FTDI_SIO_SET_FLOW_CTRL_REQUEST,
@@ -2857,7 +2855,7 @@ static int ftdi_get_modem_status(struct usb_serial_port *port,
usb_rcvctrlpipe(port->serial->dev, 0),
FTDI_SIO_GET_MODEM_STATUS_REQUEST,
FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE,
- 0, priv->interface,
+ 0, priv->channel,
buf, len, WDR_TIMEOUT);
/* NOTE: We allow short responses and handle that below. */
@@ -40,11 +40,11 @@
#define FTDI_SIO_READ_PINS 0x0c /* Read immediate value of pins */
#define FTDI_SIO_READ_EEPROM 0x90 /* Read EEPROM */
-/* Interface indices for FT2232, FT2232H and FT4232H devices */
-#define INTERFACE_A 1
-#define INTERFACE_B 2
-#define INTERFACE_C 3
-#define INTERFACE_D 4
+/* Channel indices for FT2232, FT2232H and FT4232H devices */
+#define CHANNEL_A 1
+#define CHANNEL_B 2
+#define CHANNEL_C 3
+#define CHANNEL_D 4
/*
Multi-channel devices require a channel selector to be included in control requests. Replace "interface" with the less ambiguous "channel", which is the terminology used for newer devices, in the corresponding defines and variables. Signed-off-by: Johan Hovold <johan@kernel.org> --- drivers/usb/serial/ftdi_sio.c | 40 +++++++++++++++++------------------ drivers/usb/serial/ftdi_sio.h | 10 ++++----- 2 files changed, 24 insertions(+), 26 deletions(-)