@@ -13110,6 +13110,14 @@ S: Supported
F: Documentation/devicetree/bindings/mtd/atmel-nand.txt
F: drivers/mtd/nand/raw/atmel/*
+MICROCHIP PCI1XXXX I2C DRIVER
+M: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
+M: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
+M: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
+L: linux-i2c@vger.kernel.org
+S: Maintained
+F: drivers/i2c/busses/i2c-mchp-pci1xxxx.c
+
MICROCHIP PWM DRIVER
M: Claudiu Beznea <claudiu.beznea@microchip.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -1244,6 +1244,16 @@ config I2C_PARPORT
This support is also available as a module. If so, the module
will be called i2c-parport.
+config I2C_PCI1XXXX
+ tristate "PCI1XXXX I2C Host Adapter"
+ depends on PCI
+ help
+ If you say yes to this option, support will be included for
+ Microchip PCI1XXXX's I2C interface.
+
+ This driver can also be built as a module. If so, the module will
+ be called i2c-mchp-pci1xxxx.
+
config I2C_ROBOTFUZZ_OSIF
tristate "RobotFuzz Open Source InterFace USB adapter"
depends on USB
@@ -131,6 +131,7 @@ obj-$(CONFIG_I2C_DIOLAN_U2C) += i2c-diolan-u2c.o
obj-$(CONFIG_I2C_DLN2) += i2c-dln2.o
obj-$(CONFIG_I2C_CP2615) += i2c-cp2615.o
obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o
+obj-$(CONFIG_I2C_PCI1XXXX) += i2c-mchp-pci1xxxx.o
obj-$(CONFIG_I2C_ROBOTFUZZ_OSIF) += i2c-robotfuzz-osif.o
obj-$(CONFIG_I2C_TAOS_EVM) += i2c-taos-evm.o
obj-$(CONFIG_I2C_TINY_USB) += i2c-tiny-usb.o
new file mode 100644
@@ -0,0 +1,1255 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Microchip PCI1XXXX I2C adapter driver for PCIe Switch
+ * which has I2C controller in one of its downstream functions
+ *
+ * Copyright (C) 2021 - 2022 Microchip Technology Inc.
+ *
+ * Authors: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
+ * Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
+ */
+
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/i2c-smbus.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+
+#define SMBUS_MAST_CORE_ADDR_BASE 0x00000
+#define SMBUS_MAST_SYS_REG_ADDR_BASE 0x01000
+
+#define PCI1XXXX_IRQ_FLAGS 0
+
+/* SMB register space */
+#define SMB_CORE_CTRL_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x00)
+
+#define SMB_CORE_CTRL_ESO BIT(6)
+#define SMB_CORE_CTRL_FW_ACK BIT(4)
+
+#define SMB_CORE_CMD_REG_OFF3 (SMBUS_MAST_CORE_ADDR_BASE + 0x0F)
+#define SMB_CORE_CMD_REG_OFF2 (SMBUS_MAST_CORE_ADDR_BASE + 0x0E)
+#define SMB_CORE_CMD_REG_OFF1 (SMBUS_MAST_CORE_ADDR_BASE + 0x0D)
+
+#define SMB_CORE_CMD_READM BIT(4)
+#define SMB_CORE_CMD_STOP BIT(2)
+#define SMB_CORE_CMD_START BIT(0)
+
+#define SMB_CORE_CMD_REG_OFF0 (SMBUS_MAST_CORE_ADDR_BASE + 0x0C)
+
+#define SMB_CORE_CMD_M_PROCEED BIT(1)
+#define SMB_CORE_CMD_M_RUN BIT(0)
+
+#define SMB_CORE_SR_HOLD_TIME_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x18)
+
+/*
+ * SR_HOLD_TIME_XKHZ_TICKS field will indicate the number of ticks of the
+ * baud clock required to program 'Hold Time' at X KHz.
+ */
+#define SR_HOLD_TIME_100KHZ_TICKS 133
+#define SR_HOLD_TIME_400KHZ_TICKS 20
+#define SR_HOLD_TIME_1000KHZ_TICKS 11
+
+#define SMB_CORE_COMPLETION_REG_OFF3 (SMBUS_MAST_CORE_ADDR_BASE + 0x23)
+
+#define COMPLETION_MDONE BIT(6)
+#define COMPLETION_IDLE BIT(5)
+#define COMPLETION_MNAKX BIT(0)
+
+#define SMB_CORE_IDLE_SCALING_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x24)
+
+/*
+ * FAIR_BUS_IDLE_MIN_XKHZ_TICKS field will indicate the number of ticks of
+ * the baud clock required to program 'fair idle delay' at X KHz. Fair idle
+ * delay establishes the MCTP T(IDLE_DELAY) period.
+ */
+#define FAIR_BUS_IDLE_MIN_100KHZ_TICKS 969
+#define FAIR_BUS_IDLE_MIN_400KHZ_TICKS 157
+#define FAIR_BUS_IDLE_MIN_1000KHZ_TICKS 157
+
+/*
+ * FAIR_IDLE_DELAY_XKHZ_TICKS field will indicate the number of ticks of the
+ * baud clock required to satisfy the fairness protocol at X KHz.
+ */
+#define FAIR_IDLE_DELAY_100KHZ_TICKS 1000
+#define FAIR_IDLE_DELAY_400KHZ_TICKS 500
+#define FAIR_IDLE_DELAY_1000KHZ_TICKS 500
+
+#define SMB_IDLE_SCALING_100KHZ ((FAIR_IDLE_DELAY_100KHZ_TICKS << 16) | \
+ FAIR_BUS_IDLE_MIN_100KHZ_TICKS)
+#define SMB_IDLE_SCALING_400KHZ ((FAIR_IDLE_DELAY_400KHZ_TICKS << 16) | \
+ FAIR_BUS_IDLE_MIN_400KHZ_TICKS)
+#define SMB_IDLE_SCALING_1000KHZ ((FAIR_IDLE_DELAY_1000KHZ_TICKS << 16) | \
+ FAIR_BUS_IDLE_MIN_1000KHZ_TICKS)
+
+#define SMB_CORE_CONFIG_REG3 (SMBUS_MAST_CORE_ADDR_BASE + 0x2B)
+
+#define SMB_CONFIG3_ENMI BIT(6)
+#define SMB_CONFIG3_ENIDI BIT(5)
+
+#define SMB_CORE_CONFIG_REG2 (SMBUS_MAST_CORE_ADDR_BASE + 0x2A)
+#define SMB_CORE_CONFIG_REG1 (SMBUS_MAST_CORE_ADDR_BASE + 0x29)
+
+#define SMB_CONFIG1_ASR BIT(7)
+#define SMB_CONFIG1_ENAB BIT(2)
+#define SMB_CONFIG1_RESET BIT(1)
+#define SMB_CONFIG1_FEN BIT(0)
+
+#define SMB_CORE_BUS_CLK_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x2C)
+
+/*
+ * BUS_CLK_XKHZ_LOW_PERIOD_TICKS field defines the number of I2C Baud Clock
+ * periods that make up the low phase of the I2C/SMBus bus clock at X KHz.
+ */
+#define BUS_CLK_100KHZ_LOW_PERIOD_TICKS 156
+#define BUS_CLK_400KHZ_LOW_PERIOD_TICKS 41
+#define BUS_CLK_1000KHZ_LOW_PERIOD_TICKS 15
+
+/*
+ * BUS_CLK_XKHZ_HIGH_PERIOD_TICKS field defines the number of I2C Baud Clock
+ * periods that make up the high phase of the I2C/SMBus bus clock at X KHz.
+ */
+#define BUS_CLK_100KHZ_HIGH_PERIOD_TICKS 154
+#define BUS_CLK_400KHZ_HIGH_PERIOD_TICKS 35
+#define BUS_CLK_1000KHZ_HIGH_PERIOD_TICKS 14
+
+#define BUS_CLK_100KHZ ((BUS_CLK_100KHZ_HIGH_PERIOD_TICKS << 8) | \
+ BUS_CLK_100KHZ_LOW_PERIOD_TICKS)
+#define BUS_CLK_400KHZ ((BUS_CLK_400KHZ_HIGH_PERIOD_TICKS << 8) | \
+ BUS_CLK_400KHZ_LOW_PERIOD_TICKS)
+#define BUS_CLK_1000KHZ ((BUS_CLK_1000KHZ_HIGH_PERIOD_TICKS << 8) | \
+ BUS_CLK_1000KHZ_LOW_PERIOD_TICKS)
+
+#define SMB_CORE_CLK_SYNC_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x3C)
+/*
+ * CLK_SYNC_XKHZ defines the number of clock cycles to sync up to the external
+ * clock before comparing the internal and external clocks for clock stretching
+ * at X KHz.
+ */
+#define CLK_SYNC_100KHZ 4
+#define CLK_SYNC_400KHZ 4
+#define CLK_SYNC_1000KHZ 4
+
+#define SMB_CORE_DATA_TIMING_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x40)
+
+/*
+ *
+ * FIRST_START_HOLD_XKHZ_TICKS will indicate the number of ticks of the baud
+ * clock required to program 'FIRST_START_HOLD' timer at X KHz. This timer
+ * determines the SCLK hold time following SDAT driven low during the first
+ * START bit in a transfer.
+ */
+#define FIRST_START_HOLD_100KHZ_TICKS 22
+#define FIRST_START_HOLD_400KHZ_TICKS 16
+#define FIRST_START_HOLD_1000KHZ_TICKS 6
+
+/*
+ * STOP_SETUP_XKHZ_TICKS will indicate the number of ticks of the baud clock
+ * required to program 'STOP_SETUP' timer at X KHz. This timer determines the
+ * SDAT setup time from the rising edge of SCLK for a STOP condition.
+ */
+#define STOP_SETUP_100KHZ_TICKS 157
+#define STOP_SETUP_400KHZ_TICKS 20
+#define STOP_SETUP_1000KHZ_TICKS 12
+
+/*
+ * RESTART_SETUP_XKHZ_TICKS will indicate the number of ticks of the baud clock
+ * required to program 'RESTART_SETUP' timer at X KHz. This timer determines the
+ * SDAT setup time from the rising edge of SCLK for a repeated START condition.
+ */
+#define RESTART_SETUP_100KHZ_TICKS 157
+#define RESTART_SETUP_400KHZ_TICKS 20
+#define RESTART_SETUP_1000KHZ_TICKS 12
+
+/*
+ * DATA_HOLD_XKHZ_TICKS will indicate the number of ticks of the baud clock
+ * required to program 'DATA_HOLD' timer at X KHz. This timer determines the
+ * SDAT hold time following SCLK driven low.
+ */
+#define DATA_HOLD_100KHZ_TICKS 2
+#define DATA_HOLD_400KHZ_TICKS 2
+#define DATA_HOLD_1000KHZ_TICKS 2
+
+#define DATA_TIMING_100KHZ ((FIRST_START_HOLD_100KHZ_TICKS << 24) | \
+ (STOP_SETUP_100KHZ_TICKS << 16) | \
+ (RESTART_SETUP_100KHZ_TICKS << 8) | \
+ DATA_HOLD_100KHZ_TICKS)
+#define DATA_TIMING_400KHZ ((FIRST_START_HOLD_400KHZ_TICKS << 24) | \
+ (STOP_SETUP_400KHZ_TICKS << 16) | \
+ (RESTART_SETUP_400KHZ_TICKS << 8) | \
+ DATA_HOLD_400KHZ_TICKS)
+#define DATA_TIMING_1000KHZ ((FIRST_START_HOLD_1000KHZ_TICKS << 24) | \
+ (STOP_SETUP_1000KHZ_TICKS << 16) | \
+ (RESTART_SETUP_1000KHZ_TICKS << 8) | \
+ DATA_HOLD_1000KHZ_TICKS)
+
+#define SMB_CORE_TO_SCALING_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x44)
+
+/*
+ * BUS_IDLE_MIN_XKHZ_TICKS defines Bus Idle Minimum Time
+ * Bus Idle Minimum time = BUS_IDLE_MIN[7:0] x Baud_Clock_Period x
+ * (BUS_IDLE_MIN_XKHZ_TICKS[7] ? 4,1)
+ */
+#define BUS_IDLE_MIN_100KHZ_TICKS 167
+#define BUS_IDLE_MIN_400KHZ_TICKS 139
+#define BUS_IDLE_MIN_1000KHZ_TICKS 133
+
+/*
+ * CTRL_CUM_TIME_OUT_XKHZ_TICKS defines SMBus Controller Cumulative Time-Out
+ * SMBus Controller Cumulative Time-Out duration =
+ * CTRL_CUM_TIME_OUT_XKHZ_TICKS[7:0] x Baud_Clock_Period x 2048
+ */
+#define CTRL_CUM_TIME_OUT_100KHZ_TICKS 159
+#define CTRL_CUM_TIME_OUT_400KHZ_TICKS 159
+#define CTRL_CUM_TIME_OUT_1000KHZ_TICKS 159
+
+/*
+ * TARGET_CUM_TIME_OUT_XKHZ_TICKS defines SMBus Target Cumulative Time-Out duration
+ * SMBus Target Cumulative Time-Out duration = TARGET_CUM_TIME_OUT_XKHZ_TICKS[7:0] x
+ * Baud_Clock_Period x 4096
+ */
+#define TARGET_CUM_TIME_OUT_100KHZ_TICKS 199
+#define TARGET_CUM_TIME_OUT_400KHZ_TICKS 199
+#define TARGET_CUM_TIME_OUT_1000KHZ_TICKS 199
+
+/*
+ * CLOCK_HIGH_TIME_OUT_XKHZ defines Clock High time out period
+ * Clock High time out period = CLOCK_HIGH_TIME_OUT_XKHZ[7:0] x Baud_Clock_Period x 8
+ */
+#define CLOCK_HIGH_TIME_OUT_100KHZ_TICKS 204
+#define CLOCK_HIGH_TIME_OUT_400KHZ_TICKS 204
+#define CLOCK_HIGH_TIME_OUT_1000KHZ_TICKS 204
+
+#define TO_SCALING_100KHZ ((BUS_IDLE_MIN_100KHZ_TICKS << 24) | \
+ (CTRL_CUM_TIME_OUT_100KHZ_TICKS << 16) | \
+ (TARGET_CUM_TIME_OUT_100KHZ_TICKS << 8) | \
+ CLOCK_HIGH_TIME_OUT_100KHZ_TICKS)
+#define TO_SCALING_400KHZ ((BUS_IDLE_MIN_400KHZ_TICKS << 24) | \
+ (CTRL_CUM_TIME_OUT_400KHZ_TICKS << 16) | \
+ (TARGET_CUM_TIME_OUT_400KHZ_TICKS << 8) | \
+ CLOCK_HIGH_TIME_OUT_400KHZ_TICKS)
+#define TO_SCALING_1000KHZ ((BUS_IDLE_MIN_1000KHZ_TICKS << 24) | \
+ (CTRL_CUM_TIME_OUT_1000KHZ_TICKS << 16) | \
+ (TARGET_CUM_TIME_OUT_1000KHZ_TICKS << 8) | \
+ CLOCK_HIGH_TIME_OUT_1000KHZ_TICKS)
+
+#define I2C_SCL_PAD_CTRL_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x100)
+#define I2C_SDA_PAD_CTRL_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x101)
+
+#define I2C_FOD_EN BIT(4)
+#define I2C_PULL_UP_EN BIT(3)
+#define I2C_PULL_DOWN_EN BIT(2)
+#define I2C_INPUT_EN BIT(1)
+#define I2C_OUTPUT_EN BIT(0)
+
+#define SMBUS_CONTROL_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x200)
+
+#define CTL_RESET_COUNTERS BIT(3)
+#define CTL_TRANSFER_DIR BIT(2)
+#define CTL_HOST_FIFO_ENTRY BIT(1)
+#define CTL_RUN BIT(0)
+
+#define I2C_DIRN_WRITE 0
+#define I2C_DIRN_READ 1
+
+#define SMBUS_STATUS_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x204)
+
+#define STA_DMA_TERM BIT(7)
+#define STA_DMA_REQ BIT(6)
+#define STA_THRESHOLD BIT(2)
+#define STA_BUF_FULL BIT(1)
+#define STA_BUF_EMPTY BIT(0)
+
+#define SMBUS_INTR_STAT_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x208)
+
+#define INTR_STAT_DMA_TERM BIT(7)
+#define INTR_STAT_THRESHOLD BIT(2)
+#define INTR_STAT_BUF_FULL BIT(1)
+#define INTR_STAT_BUF_EMPTY BIT(0)
+
+#define SMBUS_INTR_MSK_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x20C)
+
+#define INTR_MSK_DMA_TERM BIT(7)
+#define INTR_MSK_THRESHOLD BIT(2)
+#define INTR_MSK_BUF_FULL BIT(1)
+#define INTR_MSK_BUF_EMPTY BIT(0)
+
+#define ALL_NW_LAYER_INTERRUPTS (INTR_MSK_DMA_TERM | INTR_MSK_THRESHOLD |\
+ INTR_MSK_BUF_FULL | INTR_MSK_BUF_EMPTY)
+
+#define SMBUS_MCU_COUNTER_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x214)
+
+#define SMBALERT_MST_PAD_CTRL_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x230)
+
+#define SMBALERT_MST_PU BIT(0)
+
+#define SMBUS_GEN_INT_STAT_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x23C)
+
+#define SMBUS_GEN_INT_MASK_REG_OFF (SMBUS_MAST_CORE_ADDR_BASE + 0x240)
+
+#define SMBALERT_INTR_MASK BIT(10)
+#define I2C_BUF_MSTR_INTR_MASK BIT(9)
+#define I2C_INTR_MASK BIT(8)
+#define SMBALERT_WAKE_INTR_MASK BIT(2)
+#define I2C_BUF_MSTR_WAKE_INTR_MASK BIT(1)
+#define I2C_WAKE_INTR_MASK BIT(0)
+
+#define ALL_HIGH_LAYER_INTR (SMBALERT_INTR_MASK | I2C_BUF_MSTR_INTR_MASK | \
+ I2C_INTR_MASK | SMBALERT_WAKE_INTR_MASK | \
+ I2C_BUF_MSTR_WAKE_INTR_MASK | \
+ I2C_WAKE_INTR_MASK)
+
+#define SMBUS_RESET_REG (SMBUS_MAST_CORE_ADDR_BASE + 0x248)
+
+#define PERI_SMBUS_D3_RESET_DIS BIT(16)
+
+#define SMBUS_MST_BUF (SMBUS_MAST_CORE_ADDR_BASE + 0x280)
+
+#define SMBUS_MAST_BUF_MAX_SIZE 0x80
+
+#define I2C_FLAGS_DIRECT_MODE BIT(7)
+#define I2C_FLAGS_POLLING_MODE BIT(6)
+#define I2C_FLAGS_STOP BIT(5)
+#define I2C_FLAGS_SMB_BLK_READ BIT(4)
+
+#define PCI1XXXX_I2C_TIMEOUT_MS 1000
+
+/* General Purpose Register */
+#define SMB_GPR_REG (SMBUS_MAST_CORE_ADDR_BASE + 0x1000 + 0x0c00 + \
+ 0x00)
+
+/* Lock Register */
+#define SMB_GPR_LOCK_REG (SMBUS_MAST_CORE_ADDR_BASE + 0x1000 + 0x0000 + \
+ 0x00A0)
+
+#define SMBUS_PERI_LOCK BIT(3)
+
+/*
+ * struct pci1xxxx_i2c - private structure for the I2C controller
+ * @i2c_xfer_done: used for synchronisation between foreground & isr
+ * @i2c_xfer_in_progress: boolean to indicate whether a transfer is in
+ * progress or not
+ * @adap: I2C adapter instance
+ * @i2c_base: pci base address of the I2C controller
+ * @freq: frequency of I2C transfer
+ * @flags: internal flags to store transfer conditions
+ */
+struct pci1xxxx_i2c {
+ struct completion i2c_xfer_done;
+ bool i2c_xfer_in_progress;
+ struct i2c_adapter adap;
+ void __iomem *i2c_base;
+ u32 freq;
+ u32 flags;
+};
+
+static int set_sys_lock(void __iomem *addr)
+{
+ u8 data;
+
+ writel(SMBUS_PERI_LOCK, addr);
+ data = readl(addr);
+ if (data != SMBUS_PERI_LOCK)
+ return -EPERM;
+
+ return 0;
+}
+
+static int release_sys_lock(void __iomem *addr)
+{
+ u8 data;
+
+ data = readl(addr);
+ if (data != SMBUS_PERI_LOCK)
+ return 0;
+
+ writel(0, addr);
+ data = readl(addr);
+ if (data & SMBUS_PERI_LOCK)
+ return -EPERM;
+
+ return 0;
+}
+
+static void pci1xxxx_ack_high_level_intr(struct pci1xxxx_i2c *i2c, u16 intr_msk)
+{
+ writew(intr_msk, i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF);
+}
+
+static void pci1xxxx_i2c_configure_smbalert_pin(struct pci1xxxx_i2c *i2c,
+ bool enable)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMBALERT_MST_PAD_CTRL_REG_OFF);
+
+ if (enable)
+ regval |= SMBALERT_MST_PU;
+ else
+ regval &= ~SMBALERT_MST_PU;
+
+ writeb(regval, i2c->i2c_base + SMBALERT_MST_PAD_CTRL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_send_start_stop(struct pci1xxxx_i2c *i2c, bool start)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMB_CORE_CMD_REG_OFF1);
+
+ if (start)
+ regval |= SMB_CORE_CMD_START;
+ else
+ regval |= SMB_CORE_CMD_STOP;
+
+ writeb(regval, i2c->i2c_base + SMB_CORE_CMD_REG_OFF1);
+}
+
+/*
+ * When accessing the core control reg, we should not do a read modified write
+ * as they are write '1' to clear bits. Instead we need to write with the specific
+ * bits that needs to be set
+ */
+static void pci1xxxx_i2c_set_clear_FW_ACK(struct pci1xxxx_i2c *i2c, bool set)
+{
+ u8 regval;
+
+ if (set)
+ regval = SMB_CORE_CTRL_FW_ACK | SMB_CORE_CTRL_ESO;
+ else
+ regval = SMB_CORE_CTRL_ESO;
+
+ writeb(regval, i2c->i2c_base + SMB_CORE_CTRL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_buffer_write(struct pci1xxxx_i2c *i2c, u8 slaveaddr,
+ u8 transferlen, unsigned char *buf)
+{
+ if (slaveaddr) {
+ writeb(slaveaddr, i2c->i2c_base + SMBUS_MST_BUF);
+ if (buf)
+ memcpy_toio((i2c->i2c_base + SMBUS_MST_BUF + 1), buf, transferlen);
+ } else {
+ if (buf)
+ memcpy_toio((i2c->i2c_base + SMBUS_MST_BUF), buf, transferlen);
+ }
+}
+
+/*
+ * When accessing the core control reg, we should not do a read modified write
+ * as there are write '1' to clear bits. Instead we need to write with the specific
+ * bits that needs to be set
+ */
+static void pci1xxxx_i2c_enable_ESO(struct pci1xxxx_i2c *i2c)
+{
+ writeb(SMB_CORE_CTRL_ESO, i2c->i2c_base + SMB_CORE_CTRL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_reset_counters(struct pci1xxxx_i2c *i2c)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+ regval |= CTL_RESET_COUNTERS;
+ writeb(regval, i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_set_transfer_dir(struct pci1xxxx_i2c *i2c, u8 direction)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+ if (direction == I2C_DIRN_WRITE)
+ regval &= ~CTL_TRANSFER_DIR;
+ else
+ regval |= CTL_TRANSFER_DIR;
+
+ writeb(regval, i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_set_mcu_count(struct pci1xxxx_i2c *i2c, u8 count)
+{
+ writeb(count, i2c->i2c_base + SMBUS_MCU_COUNTER_REG_OFF);
+}
+
+static void pci1xxxx_i2c_set_read_count(struct pci1xxxx_i2c *i2c, u8 readcount)
+{
+ writeb(readcount, i2c->i2c_base + SMB_CORE_CMD_REG_OFF3);
+}
+
+static void pci1xxxx_i2c_set_write_count(struct pci1xxxx_i2c *i2c, u8 writecount)
+{
+ writeb(writecount, i2c->i2c_base + SMB_CORE_CMD_REG_OFF2);
+}
+
+static void pci1xxxx_i2c_set_DMA_run(struct pci1xxxx_i2c *i2c)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+ regval |= CTL_RUN;
+ writeb(regval, i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_set_mrun_proceed(struct pci1xxxx_i2c *i2c)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMB_CORE_CMD_REG_OFF0);
+ regval |= SMB_CORE_CMD_M_RUN;
+ regval |= SMB_CORE_CMD_M_PROCEED;
+ writeb(regval, i2c->i2c_base + SMB_CORE_CMD_REG_OFF0);
+}
+
+static void pci1xxxx_i2c_start_DMA(struct pci1xxxx_i2c *i2c)
+{
+ pci1xxxx_i2c_set_DMA_run(i2c);
+ pci1xxxx_i2c_set_mrun_proceed(i2c);
+}
+
+static void pci1xxxx_i2c_config_asr(struct pci1xxxx_i2c *i2c, bool enable)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMB_CORE_CONFIG_REG1);
+ if (enable)
+ regval |= SMB_CONFIG1_ASR;
+ else
+ regval &= ~SMB_CONFIG1_ASR;
+ writeb(regval, i2c->i2c_base + SMB_CORE_CONFIG_REG1);
+}
+
+static irqreturn_t pci1xxxx_i2c_isr(int irq, void *dev)
+{
+ irqreturn_t intr_handled = IRQ_NONE;
+ struct pci1xxxx_i2c *i2c = dev;
+ u16 reg1;
+ u8 reg3;
+
+ /*
+ * Read the SMBus interrupt status register to see if the
+ * DMA_TERM interrupt has caused this callback
+ */
+ reg1 = readw(i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF);
+
+ if (reg1 & I2C_BUF_MSTR_INTR_MASK) {
+ reg3 = readb(i2c->i2c_base + SMBUS_INTR_STAT_REG_OFF);
+ if (reg3 & INTR_STAT_DMA_TERM) {
+ complete(&i2c->i2c_xfer_done);
+ intr_handled = IRQ_HANDLED;
+ writeb(INTR_STAT_DMA_TERM,
+ i2c->i2c_base + SMBUS_INTR_STAT_REG_OFF);
+ }
+ pci1xxxx_ack_high_level_intr(i2c, I2C_BUF_MSTR_INTR_MASK);
+ }
+
+ if (reg1 & SMBALERT_INTR_MASK) {
+ intr_handled = IRQ_HANDLED;
+ pci1xxxx_ack_high_level_intr(i2c, SMBALERT_INTR_MASK);
+ }
+
+ return intr_handled;
+}
+
+static void pci1xxxx_i2c_set_count(struct pci1xxxx_i2c *i2c, u8 mcucount,
+ u8 writecount, u8 readcount)
+{
+ pci1xxxx_i2c_set_mcu_count(i2c, mcucount);
+ pci1xxxx_i2c_set_write_count(i2c, writecount);
+ pci1xxxx_i2c_set_read_count(i2c, readcount);
+}
+
+static void pci1xxxx_i2c_set_readm(struct pci1xxxx_i2c *i2c, bool enable)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMB_CORE_CMD_REG_OFF1);
+ if (enable)
+ regval |= SMB_CORE_CMD_READM;
+ else
+ regval &= ~SMB_CORE_CMD_READM;
+
+ writeb(regval, i2c->i2c_base + SMB_CORE_CMD_REG_OFF1);
+}
+
+static void pci1xxxx_ack_nw_layer_intr(struct pci1xxxx_i2c *i2c,
+ u8 ack_intr_msk)
+{
+ writeb(ack_intr_msk, i2c->i2c_base + SMBUS_INTR_STAT_REG_OFF);
+}
+
+static void pci1xxxx_config_nw_layer_intr(struct pci1xxxx_i2c *i2c,
+ u8 intr_msk, bool enable)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMBUS_INTR_MSK_REG_OFF);
+ if (enable)
+ regval &= ~(intr_msk);
+ else
+ regval |= intr_msk;
+
+ writeb(regval, i2c->i2c_base + SMBUS_INTR_MSK_REG_OFF);
+}
+
+static void pci1xxxx_i2c_config_padctrl(struct pci1xxxx_i2c *i2c, bool enable)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + I2C_SCL_PAD_CTRL_REG_OFF);
+ if (enable)
+ regval |= (I2C_INPUT_EN | I2C_OUTPUT_EN);
+ else
+ regval &= ~(I2C_INPUT_EN | I2C_OUTPUT_EN);
+
+ writeb(regval, i2c->i2c_base + I2C_SCL_PAD_CTRL_REG_OFF);
+
+ regval = readb(i2c->i2c_base + I2C_SDA_PAD_CTRL_REG_OFF);
+ if (enable)
+ regval |= (I2C_INPUT_EN | I2C_OUTPUT_EN);
+ else
+ regval &= ~(I2C_INPUT_EN | I2C_OUTPUT_EN);
+
+ writeb(regval, i2c->i2c_base + I2C_SDA_PAD_CTRL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_set_mode(struct pci1xxxx_i2c *i2c)
+{
+ u8 regval;
+
+ regval = readb(i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+ if (i2c->flags & I2C_FLAGS_DIRECT_MODE)
+ regval &= ~CTL_HOST_FIFO_ENTRY;
+ else
+ regval |= CTL_HOST_FIFO_ENTRY;
+
+ writeb(regval, i2c->i2c_base + SMBUS_CONTROL_REG_OFF);
+}
+
+static void pci1xxxx_i2c_config_high_level_intr(struct pci1xxxx_i2c *i2c,
+ u16 intr_msk, bool enable)
+{
+ u16 regval;
+
+ regval = readw(i2c->i2c_base + SMBUS_GEN_INT_MASK_REG_OFF);
+ if (enable)
+ regval &= ~(intr_msk);
+ else
+ regval |= intr_msk;
+ writew(regval, i2c->i2c_base + SMBUS_GEN_INT_MASK_REG_OFF);
+}
+
+static void pci1xxxx_i2c_configure_core_reg(struct pci1xxxx_i2c *i2c, bool enable)
+{
+ u8 reg1;
+ u8 reg3;
+
+ reg1 = readb(i2c->i2c_base + SMB_CORE_CONFIG_REG1);
+ reg3 = readb(i2c->i2c_base + SMB_CORE_CONFIG_REG3);
+ if (enable) {
+ reg1 |= (SMB_CONFIG1_ENAB | SMB_CONFIG1_FEN);
+ reg3 |= (SMB_CONFIG3_ENMI | SMB_CONFIG3_ENIDI);
+ } else {
+ reg1 &= ~(SMB_CONFIG1_ENAB | SMB_CONFIG1_FEN);
+ reg3 &= ~(SMB_CONFIG3_ENMI | SMB_CONFIG3_ENIDI);
+ }
+
+ writeb(reg1, i2c->i2c_base + SMB_CORE_CONFIG_REG1);
+ writeb(reg3, i2c->i2c_base + SMB_CORE_CONFIG_REG3);
+}
+
+static void pci1xxxx_i2c_set_freq(struct pci1xxxx_i2c *i2c)
+{
+ switch (i2c->freq) {
+ case I2C_MAX_STANDARD_MODE_FREQ:
+ writeb(SR_HOLD_TIME_100KHZ_TICKS,
+ i2c->i2c_base + SMB_CORE_SR_HOLD_TIME_REG_OFF);
+ writel(SMB_IDLE_SCALING_100KHZ,
+ i2c->i2c_base + SMB_CORE_IDLE_SCALING_REG_OFF);
+ writew(BUS_CLK_100KHZ,
+ i2c->i2c_base + SMB_CORE_BUS_CLK_REG_OFF);
+ writel(CLK_SYNC_100KHZ,
+ i2c->i2c_base + SMB_CORE_CLK_SYNC_REG_OFF);
+ writel(DATA_TIMING_100KHZ,
+ i2c->i2c_base + SMB_CORE_DATA_TIMING_REG_OFF);
+ writel(TO_SCALING_100KHZ,
+ i2c->i2c_base + SMB_CORE_TO_SCALING_REG_OFF);
+ break;
+
+ case I2C_MAX_FAST_MODE_PLUS_FREQ:
+ writeb(SR_HOLD_TIME_1000KHZ_TICKS,
+ i2c->i2c_base + SMB_CORE_SR_HOLD_TIME_REG_OFF);
+ writel(SMB_IDLE_SCALING_1000KHZ,
+ i2c->i2c_base + SMB_CORE_IDLE_SCALING_REG_OFF);
+ writew(BUS_CLK_1000KHZ,
+ i2c->i2c_base + SMB_CORE_BUS_CLK_REG_OFF);
+ writel(CLK_SYNC_1000KHZ,
+ i2c->i2c_base + SMB_CORE_CLK_SYNC_REG_OFF);
+ writel(DATA_TIMING_1000KHZ,
+ i2c->i2c_base + SMB_CORE_DATA_TIMING_REG_OFF);
+ writel(TO_SCALING_1000KHZ,
+ i2c->i2c_base + SMB_CORE_TO_SCALING_REG_OFF);
+ break;
+
+ case I2C_MAX_FAST_MODE_FREQ:
+ default:
+ writeb(SR_HOLD_TIME_400KHZ_TICKS,
+ i2c->i2c_base + SMB_CORE_SR_HOLD_TIME_REG_OFF);
+ writel(SMB_IDLE_SCALING_400KHZ,
+ i2c->i2c_base + SMB_CORE_IDLE_SCALING_REG_OFF);
+ writew(BUS_CLK_400KHZ,
+ i2c->i2c_base + SMB_CORE_BUS_CLK_REG_OFF);
+ writel(CLK_SYNC_400KHZ,
+ i2c->i2c_base + SMB_CORE_CLK_SYNC_REG_OFF);
+ writel(DATA_TIMING_400KHZ,
+ i2c->i2c_base + SMB_CORE_DATA_TIMING_REG_OFF);
+ writel(TO_SCALING_400KHZ,
+ i2c->i2c_base + SMB_CORE_TO_SCALING_REG_OFF);
+ break;
+ }
+}
+
+static void pci1xxxx_i2c_init(struct pci1xxxx_i2c *i2c)
+{
+ u8 regval;
+ u8 ret;
+
+ ret = set_sys_lock(i2c->i2c_base + SMB_GPR_LOCK_REG);
+ if (ret != -EPERM) {
+ regval = readl(i2c->i2c_base + SMB_GPR_REG);
+ release_sys_lock(i2c->i2c_base + SMB_GPR_LOCK_REG);
+ } else {
+ /*
+ * Configure I2C Fast Mode as default frequency if unable
+ * to acquire sys lock
+ */
+ regval = 0;
+ }
+
+ switch (regval) {
+ case 0:
+ i2c->freq = I2C_MAX_FAST_MODE_FREQ;
+ pci1xxxx_i2c_set_freq(i2c);
+ break;
+ case 1:
+ i2c->freq = I2C_MAX_STANDARD_MODE_FREQ;
+ pci1xxxx_i2c_set_freq(i2c);
+ break;
+ case 2:
+ i2c->freq = I2C_MAX_FAST_MODE_PLUS_FREQ;
+ pci1xxxx_i2c_set_freq(i2c);
+ break;
+ case 3:
+ default:
+ break;
+ }
+
+ pci1xxxx_i2c_config_padctrl(i2c, true);
+ i2c->flags |= I2C_FLAGS_DIRECT_MODE;
+ pci1xxxx_i2c_set_mode(i2c);
+
+ /*
+ * Added as a precaution since BUF_EMPTY in status register
+ * also trigered an Interrupt
+ */
+ writeb(STA_BUF_EMPTY, i2c->i2c_base + SMBUS_STATUS_REG_OFF);
+
+ /* Configure core I2c control registers */
+ pci1xxxx_i2c_configure_core_reg(i2c, true);
+
+ /*
+ * Enable Pullup for the SMB alert pin which is just used for
+ * wakeup right now
+ */
+ pci1xxxx_i2c_configure_smbalert_pin(i2c, true);
+}
+
+static void pci1xxxx_i2c_clear_flags(struct pci1xxxx_i2c *i2c)
+{
+ u8 regval;
+
+ /* Reset the internal buffer counters */
+ pci1xxxx_i2c_reset_counters(i2c);
+
+ /* Clear low level interrupts */
+ regval = (COMPLETION_MNAKX | COMPLETION_IDLE | COMPLETION_MDONE);
+ writeb(regval, i2c->i2c_base + SMB_CORE_COMPLETION_REG_OFF3);
+
+ reinit_completion(&i2c->i2c_xfer_done);
+ pci1xxxx_ack_nw_layer_intr(i2c, ALL_NW_LAYER_INTERRUPTS);
+
+ pci1xxxx_ack_high_level_intr(i2c, ALL_HIGH_LAYER_INTR);
+}
+
+static int pci1xxxx_i2c_read(struct pci1xxxx_i2c *i2c, u8 slaveaddr,
+ unsigned char *buf, u16 total_len)
+{
+ unsigned long time_left;
+ u16 remainingbytes;
+ u8 transferlen;
+ int retval = 0;
+ u8 read_count;
+ u32 regval;
+ u16 count;
+
+ /* Enable I2C host controller by setting the ESO bit in the CONTROL REG */
+ pci1xxxx_i2c_enable_ESO(i2c);
+
+ pci1xxxx_i2c_clear_flags(i2c);
+
+ pci1xxxx_config_nw_layer_intr(i2c, INTR_MSK_DMA_TERM, true);
+
+ pci1xxxx_i2c_config_high_level_intr(i2c, (I2C_BUF_MSTR_INTR_MASK),
+ true);
+
+ /*
+ * The i2c transfer could be more than 128 bytes. Our Core is
+ * capable of only sending 128 at a time.
+ * As far as the I2C read is concerned, initailly send the
+ * read slave address along with the number of bytes to read in
+ * ReadCount. After sending the slave address the interrupt
+ * is generated. On seeing the ACK for the slave address, reverse the
+ * buffer direction and run the DMA to initiate Read from slave
+ */
+ for (count = 0; count < total_len; count += transferlen) {
+ /*
+ * Before start of any transaction clear the existing
+ * START/STOP conditions
+ */
+ writeb(0x00, i2c->i2c_base + SMB_CORE_CMD_REG_OFF1);
+
+ remainingbytes = total_len - count;
+
+ transferlen = min_t(u16, remainingbytes, (u16)(SMBUS_MAST_BUF_MAX_SIZE));
+
+ /*
+ * Send STOP bit for the last chunk in the transaction.
+ * For I2C read transaction of more than BUF_SIZE, NACK should only
+ * be sent for the last read
+ * Hence a bit FW_ACK is set for all the read chunks except for the last
+ * chunk. For the last chunk NACK should be sent and FW_ACK is cleared
+ * Send STOP only when I2C_FLAGS_STOP bit is set in the flags
+ * and only for the last transaction.
+ */
+
+ if ((count + transferlen >= total_len) && (i2c->flags & I2C_FLAGS_STOP)) {
+ pci1xxxx_i2c_set_clear_FW_ACK(i2c, false);
+ pci1xxxx_i2c_send_start_stop(i2c, 0);
+ } else {
+ pci1xxxx_i2c_set_clear_FW_ACK(i2c, true);
+ }
+
+ /* Send START bit for the first transaction */
+ if (count == 0) {
+ pci1xxxx_i2c_set_transfer_dir(i2c, I2C_DIRN_WRITE);
+
+ pci1xxxx_i2c_send_start_stop(i2c, 1);
+
+ /* Write I2c buffer with just the slave addr */
+ pci1xxxx_i2c_buffer_write(i2c, slaveaddr, 0, NULL);
+
+ /* Set the count. Readcount is the transfer bytes */
+ pci1xxxx_i2c_set_count(i2c, 1, 1, transferlen);
+
+ /*
+ * Set the Auto_start_read bit so that the HW itself
+ * will take care of the read phase.
+ */
+
+ pci1xxxx_i2c_config_asr(i2c, true);
+
+ if (i2c->flags & I2C_FLAGS_SMB_BLK_READ)
+ pci1xxxx_i2c_set_readm(i2c, true);
+
+ } else {
+ pci1xxxx_i2c_set_count(i2c, 0, 0, transferlen);
+
+ pci1xxxx_i2c_config_asr(i2c, false);
+
+ pci1xxxx_i2c_clear_flags(i2c);
+
+ pci1xxxx_i2c_set_transfer_dir(i2c, I2C_DIRN_READ);
+ }
+
+ /* Start the DMA */
+ pci1xxxx_i2c_start_DMA(i2c);
+
+ /* Wait for the DMA_TERM interrupt */
+ time_left = wait_for_completion_timeout
+ (&i2c->i2c_xfer_done,
+ msecs_to_jiffies(PCI1XXXX_I2C_TIMEOUT_MS));
+ if (time_left == 0) {
+ /* Reset the I2C core to release the bus lock */
+ pci1xxxx_i2c_init(i2c);
+ retval = -ETIMEDOUT;
+ goto cleanup;
+ }
+
+ /* Read the completion reg to know the reason for DMA_TERM */
+ regval = readb(i2c->i2c_base + SMB_CORE_COMPLETION_REG_OFF3);
+ /* Slave did not respond */
+ if (regval & COMPLETION_MNAKX) {
+ writeb(COMPLETION_MNAKX, i2c->i2c_base +
+ SMB_CORE_COMPLETION_REG_OFF3);
+ retval = -ETIMEDOUT;
+ goto cleanup;
+ }
+
+ if (i2c->flags & I2C_FLAGS_SMB_BLK_READ) {
+ buf[0] = readb(i2c->i2c_base +
+ SMBUS_MST_BUF);
+ read_count = buf[0];
+ memcpy_fromio(&buf[1], (i2c->i2c_base +
+ SMBUS_MST_BUF + 1),
+ read_count);
+ } else {
+ memcpy_fromio(&buf[count], (i2c->i2c_base +
+ SMBUS_MST_BUF), transferlen);
+ }
+ }
+
+cleanup:
+ /* Disable all the interrupts */
+ pci1xxxx_config_nw_layer_intr(i2c, INTR_MSK_DMA_TERM, false);
+ pci1xxxx_i2c_config_high_level_intr(i2c, (I2C_BUF_MSTR_INTR_MASK),
+ false);
+ pci1xxxx_i2c_config_asr(i2c, false);
+ return retval;
+}
+
+static int pci1xxxx_i2c_write(struct pci1xxxx_i2c *i2c, u8 slaveaddr,
+ unsigned char *buf, u16 total_len)
+{
+ unsigned long time_left;
+ u16 remainingbytes;
+ u8 actualwritelen;
+ u8 transferlen;
+ int retval = 0;
+ u32 regval;
+ u16 count;
+
+ /* Enable I2C host controller by setting the ESO bit in the CONTROL REG */
+ pci1xxxx_i2c_enable_ESO(i2c);
+
+ /* Set the Buffer direction */
+ pci1xxxx_i2c_set_transfer_dir(i2c, I2C_DIRN_WRITE);
+
+ pci1xxxx_config_nw_layer_intr(i2c, INTR_MSK_DMA_TERM, true);
+
+ pci1xxxx_i2c_config_high_level_intr(i2c, (I2C_BUF_MSTR_INTR_MASK),
+ true);
+
+ /*
+ * The i2c transfer could be more than 128 bytes. Our Core is
+ * capable of only sending 128 at a time.
+ */
+ for (count = 0; count < total_len; count += transferlen) {
+ /*
+ * Before start of any transaction clear the existing
+ * START/STOP conditions
+ */
+ writeb(0x00, i2c->i2c_base + SMB_CORE_CMD_REG_OFF1);
+
+ pci1xxxx_i2c_clear_flags(i2c);
+
+ remainingbytes = total_len - count;
+ /* if it is the starting of the transaction send START */
+ if (count == 0) {
+ pci1xxxx_i2c_send_start_stop(i2c, 1);
+
+ /* -1 for the slave address */
+ transferlen = min_t(u16, (u16)(SMBUS_MAST_BUF_MAX_SIZE - 1),
+ remainingbytes);
+ pci1xxxx_i2c_buffer_write(i2c, slaveaddr,
+ transferlen, &buf[count]);
+
+ /*
+ * The actual number of bytes written on the I2C bus
+ * is including the slave address
+ */
+ actualwritelen = transferlen + 1;
+
+ } else {
+ transferlen = min_t(u16, (u16)(SMBUS_MAST_BUF_MAX_SIZE),
+ remainingbytes);
+ pci1xxxx_i2c_buffer_write(i2c, 0x00, transferlen,
+ &buf[count]);
+ actualwritelen = transferlen;
+ }
+
+ pci1xxxx_i2c_set_count(i2c, actualwritelen,
+ actualwritelen, 0x00);
+
+ /*
+ * Send STOP only when I2C_FLAGS_STOP bit is set in the flags and
+ * only for the last transaction.
+ */
+
+ if (remainingbytes <= transferlen &&
+ (i2c->flags & I2C_FLAGS_STOP))
+ pci1xxxx_i2c_send_start_stop(i2c, 0);
+
+ pci1xxxx_i2c_start_DMA(i2c);
+
+ /*
+ * Wait for the DMA_TERM interrupt
+ */
+ time_left = wait_for_completion_timeout(&i2c->i2c_xfer_done,
+ msecs_to_jiffies(PCI1XXXX_I2C_TIMEOUT_MS));
+
+ if (time_left == 0) {
+ /* Reset the I2C core to release the bus lock */
+ pci1xxxx_i2c_init(i2c);
+ retval = -ETIMEDOUT;
+ goto cleanup;
+ }
+
+ regval = readb(i2c->i2c_base + SMB_CORE_COMPLETION_REG_OFF3);
+ if (regval & COMPLETION_MNAKX) {
+ writeb(COMPLETION_MNAKX, i2c->i2c_base +
+ SMB_CORE_COMPLETION_REG_OFF3);
+ retval = -ETIMEDOUT;
+ goto cleanup;
+ }
+ }
+cleanup:
+ /* Disable all the interrupts */
+ pci1xxxx_config_nw_layer_intr(i2c, INTR_MSK_DMA_TERM, false);
+ pci1xxxx_i2c_config_high_level_intr(i2c, (I2C_BUF_MSTR_INTR_MASK),
+ false);
+
+ return retval;
+}
+
+static int pci1xxxx_i2c_xfer(struct i2c_adapter *adap,
+ struct i2c_msg *msgs, int num)
+{
+ struct pci1xxxx_i2c *i2c = i2c_get_adapdata(adap);
+ u8 slaveaddr;
+ int retval;
+ u32 i;
+
+ i2c->i2c_xfer_in_progress = true;
+ for (i = 0; i < num; i++) {
+ slaveaddr = i2c_8bit_addr_from_msg(&msgs[i]);
+
+ /*
+ * Send the STOP bit if the transfer is the final one or
+ * if the I2C_M_STOP flag is set
+ */
+ if ((i == (num - 1)) || (msgs[i].flags & I2C_M_STOP))
+ i2c->flags |= I2C_FLAGS_STOP;
+ else
+ i2c->flags &= ~I2C_FLAGS_STOP;
+
+ if (msgs[i].flags & I2C_M_RECV_LEN)
+ i2c->flags |= I2C_FLAGS_SMB_BLK_READ;
+ else
+ i2c->flags &= ~I2C_FLAGS_SMB_BLK_READ;
+
+ if (msgs[i].flags & I2C_M_RD)
+ retval = pci1xxxx_i2c_read(i2c, slaveaddr,
+ msgs[i].buf, msgs[i].len);
+ else
+ retval = pci1xxxx_i2c_write(i2c, slaveaddr,
+ msgs[i].buf, msgs[i].len);
+
+ if (retval < 0)
+ break;
+ }
+ i2c->i2c_xfer_in_progress = false;
+
+ if (retval < 0)
+ return retval;
+
+ return num;
+}
+
+/*
+ * List of supported functions by the driver
+ */
+
+static u32 pci1xxxx_i2c_get_funcs(struct i2c_adapter *adap)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_PROTOCOL_MANGLING |
+ I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+ I2C_FUNC_SMBUS_READ_BYTE | I2C_FUNC_SMBUS_WRITE_BYTE |
+ I2C_FUNC_SMBUS_READ_BYTE_DATA |
+ I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
+ I2C_FUNC_SMBUS_READ_WORD_DATA |
+ I2C_FUNC_SMBUS_WRITE_WORD_DATA |
+ I2C_FUNC_SMBUS_PROC_CALL | I2C_FUNC_SMBUS_READ_BLOCK_DATA |
+ I2C_FUNC_SMBUS_WRITE_BLOCK_DATA;
+}
+
+static const struct i2c_algorithm pci1xxxx_i2c_algo = {
+ .master_xfer = pci1xxxx_i2c_xfer,
+ .functionality = pci1xxxx_i2c_get_funcs,
+};
+
+static const struct i2c_adapter pci1xxxx_i2c_ops = {
+ .owner = THIS_MODULE,
+ .name = "Pci1xxxx I2C Adapter",
+ .algo = &pci1xxxx_i2c_algo,
+};
+
+static int pci1xxxx_i2c_suspend(struct device *dev)
+{
+ struct pci1xxxx_i2c *i2c = dev_get_drvdata(dev);
+ struct pci_dev *pdev = to_pci_dev(dev);
+ u32 regval;
+
+ i2c_mark_adapter_suspended(&i2c->adap);
+
+ while ((i2c->i2c_xfer_in_progress))
+ msleep(20);
+
+ pci1xxxx_i2c_config_high_level_intr(i2c,
+ SMBALERT_WAKE_INTR_MASK,
+ true);
+
+ /*
+ * Enable the PERST_DIS bit to mask the PERST from
+ * resetting the core registers
+ */
+ regval = readl(i2c->i2c_base + SMBUS_RESET_REG);
+ regval |= PERI_SMBUS_D3_RESET_DIS;
+ writel(regval, i2c->i2c_base + SMBUS_RESET_REG);
+ /* Enable PCI wake in the PMCSR register */
+ device_set_wakeup_enable(dev, TRUE);
+ pci_wake_from_d3(pdev, TRUE);
+
+ return 0;
+}
+
+static int pci1xxxx_i2c_resume(struct device *dev)
+{
+ struct pci1xxxx_i2c *i2c = dev_get_drvdata(dev);
+ struct pci_dev *pdev = to_pci_dev(dev);
+ u32 regval;
+
+ regval = readw(i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF);
+ writew(regval, i2c->i2c_base + SMBUS_GEN_INT_STAT_REG_OFF);
+ pci1xxxx_i2c_config_high_level_intr(i2c, SMBALERT_WAKE_INTR_MASK,
+ false);
+ regval = readl(i2c->i2c_base + SMBUS_RESET_REG);
+ regval &= ~PERI_SMBUS_D3_RESET_DIS;
+ writel(regval, i2c->i2c_base + SMBUS_RESET_REG);
+
+ i2c_mark_adapter_resumed(&i2c->adap);
+
+ pci_wake_from_d3(pdev, FALSE);
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(pci1xxxx_i2c_pm_ops, pci1xxxx_i2c_suspend,
+ pci1xxxx_i2c_resume);
+
+static void pci1xxxx_i2c_shutdown(struct pci1xxxx_i2c *i2c)
+{
+ pci1xxxx_i2c_config_padctrl(i2c, false);
+ pci1xxxx_i2c_configure_core_reg(i2c, false);
+}
+
+static int pci1xxxx_i2c_probe_pci(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ struct pci1xxxx_i2c *i2c;
+ int ret;
+
+ i2c = devm_kzalloc(&pdev->dev, sizeof(*i2c), GFP_KERNEL);
+ if (!i2c)
+ return -ENOMEM;
+
+ pci_set_drvdata(pdev, i2c);
+
+ i2c->i2c_xfer_in_progress = false;
+
+ ret = pcim_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ pci_set_master(pdev);
+
+ /*
+ * We are getting the base address of the SMB core. SMB core uses
+ * BAR0 and size is 32K
+ */
+
+ ret = pcim_iomap_regions(pdev, BIT(0), pci_name(pdev));
+ if (ret < 0)
+ return -ENOMEM;
+
+ i2c->i2c_base = pcim_iomap_table(pdev)[0];
+
+ init_completion(&i2c->i2c_xfer_done);
+
+ pci1xxxx_i2c_init(i2c);
+
+ ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
+ if (ret < 0) {
+ pci1xxxx_i2c_shutdown(i2c);
+ return ret;
+ }
+
+ /* Register the isr. We are not using any isr flags here. */
+ ret = devm_request_irq(&pdev->dev, pci_irq_vector(pdev, 0),
+ pci1xxxx_i2c_isr, PCI1XXXX_IRQ_FLAGS,
+ pci_name(pdev), i2c);
+ if (ret) {
+ pci1xxxx_i2c_shutdown(i2c);
+ return ret;
+ }
+
+ i2c->adap = pci1xxxx_i2c_ops;
+ i2c->adap.class = I2C_CLASS_SPD;
+ i2c->adap.dev.parent = &pdev->dev;
+
+ snprintf(i2c->adap.name, sizeof(i2c->adap.name),
+ "MCHP PCI1xxxx i2c adapter at %s", pci_name(pdev));
+
+ i2c_set_adapdata(&i2c->adap, i2c);
+
+ ret = devm_i2c_add_adapter(&pdev->dev, &i2c->adap);
+ if (ret) {
+ dev_err(&pdev->dev, "i2c add adapter failed = %d\n", ret);
+ pci1xxxx_i2c_shutdown(i2c);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void pci1xxxx_i2c_remove_pci(struct pci_dev *pdev)
+{
+ struct pci1xxxx_i2c *i2c = pci_get_drvdata(pdev);
+
+ pci1xxxx_i2c_shutdown(i2c);
+}
+
+static const struct pci_device_id pci1xxxx_i2c_pci_id_table[] = {
+ { PCI_VDEVICE(EFAR, 0xA003) },
+ { PCI_VDEVICE(EFAR, 0xA013) },
+ { PCI_VDEVICE(EFAR, 0xA023) },
+ { PCI_VDEVICE(EFAR, 0xA033) },
+ { PCI_VDEVICE(EFAR, 0xA043) },
+ { }
+};
+MODULE_DEVICE_TABLE(pci, pci1xxxx_i2c_pci_id_table);
+
+static struct pci_driver pci1xxxx_i2c_pci_driver = {
+ .name = "i2c-mchp-pci1xxxx",
+ .id_table = pci1xxxx_i2c_pci_id_table,
+ .probe = pci1xxxx_i2c_probe_pci,
+ .remove = pci1xxxx_i2c_remove_pci,
+ .driver = {
+ .pm = &pci1xxxx_i2c_pm_ops,
+ },
+};
+module_pci_driver(pci1xxxx_i2c_pci_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Tharun Kumar P<tharunkumar.pasumarthi@microchip.com>");
+MODULE_AUTHOR("Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>");
+MODULE_DESCRIPTION("Microchip Technology Inc. pci1xxxx I2C bus driver");
Microchip pci1xxxx is an unmanaged PCIe3.1a Switch for Consumer, Industrial and Automotive applications. This switch has multiple downstream ports. In one of the Switch's Downstream port, there is a multifunction endpoint for peripherals which includes an I2C host controller. The I2C function in the endpoint operates at 100KHz, 400KHz and 1 MHz and has buffer depth of 128 bytes. This patch provides the I2C controller driver for the I2C function of the switch. Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com> --- RFC -> V2: 1. Removed pci_free_irq_vectors API in code since pcim_enable_device is used 2. Added pci1xxxx_i2c_shutdown API in failure case of pci_alloc_irq_vectors and devm_request_irq 3. Used devm variant of i2c_add_adapter 4. Resolved name collision and fixed styling issues in comments --- MAINTAINERS | 8 + drivers/i2c/busses/Kconfig | 10 + drivers/i2c/busses/Makefile | 1 + drivers/i2c/busses/i2c-mchp-pci1xxxx.c | 1255 ++++++++++++++++++++++++ 4 files changed, 1274 insertions(+) create mode 100644 drivers/i2c/busses/i2c-mchp-pci1xxxx.c