diff mbox

[RFC,3/5] dt-bindings: thermal: Add optional properties of Mediatek thermal controller

Message ID 1453452029-20843-4-git-send-email-pi-cheng.chen@linaro.org
State New
Headers show

Commit Message

pi-cheng.chen Jan. 22, 2016, 8:40 a.m. UTC
This adds optional properties of Mediatek thermal controller which are
required by SVS engine integrated with Mediatek thermal controller.

Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>

---
 .../bindings/thermal/mediatek-thermal.txt          | 23 ++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)

-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Comments

Rob Herring (Arm) Jan. 22, 2016, 10:31 p.m. UTC | #1
On Fri, Jan 22, 2016 at 04:40:27PM +0800, Pi-Cheng Chen wrote:
> This adds optional properties of Mediatek thermal controller which are

> required by SVS engine integrated with Mediatek thermal controller.

> 

> Signed-off-by: Pi-Cheng Chen <pi-cheng.chen@linaro.org>

> ---

>  .../bindings/thermal/mediatek-thermal.txt          | 23 ++++++++++++++++------

>  1 file changed, 17 insertions(+), 6 deletions(-)

> 

> diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt

> index 81f9a51..acaacaa 100644

> --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt

> +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt

> @@ -7,6 +7,11 @@ this device needs phandles to the AUXADC. Also it controls a mux in the

>  apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS

>  is also needed.

>  

> +There is another hardware engine, SVS (Smart Voltage Scaling) which shares the

> +same block of banked registers with Mediatek thermal controller. Hence the

> +driver of SVS is integrated with the driver of Mediatek thermal controller. The

> +properties required by SVS engine are optional for Mediatek thermal controller.

> +

>  Required properties:

>  - compatible: "mediatek,mt8173-thermal"

>  - reg: Address range of the thermal controller

> @@ -21,9 +26,15 @@ Required properties:

>  - #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.

>  

>  Optional properties:

> -- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If

> -               unspecified default values shall be used.

> -- nvmem-cell-names: Should be "calibration-data"

> +- clocks, clock-names: Clocks that are optional for the thermal controller.

> +	       Specify to enable SVS engine.

> +	       "svs_pll": The PLL clock should be switched to during

> +			  initialization stage of SVS engine.

> +	       "svs_mux": The MUX clock controls the clock input of SVS engine.

> +- nvmem-cells: A list of phandles to the calibration data provided by a nvmem

> +	       device. If unspecified default values shall be used. The SVS

> +	       engine will be disabled if no SVS calibration data is specified.

> +- nvmem-cell-names: Should be "calibration-data" and "svs-calibration-data"

>  

>  Example:

>  

> @@ -33,11 +44,11 @@ Example:

>  		reg = <0 0x1100b000 0 0x1000>;

>  		interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;

>  		clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;

> -		clock-names = "therm", "auxadc";

> +		clock-names = "therm", "auxadc", ;


Huh?

>  		resets = <&pericfg MT8173_PERI_THERM_SW_RST>;

>  		reset-names = "therm";

>  		mediatek,auxadc = <&auxadc>;

>  		mediatek,apmixedsys = <&apmixedsys>;

> -		nvmem-cells = <&thermal_calibration_data>;

> -		nvmem-cell-names = "calibration-data";

> +		nvmem-cells = <&thermal_calibration_data>, <&svs-calibration>;

> +		nvmem-cell-names = "calibration-data", "svs-calibration-data";

>  	};

> -- 

> 1.9.1

> 

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
index 81f9a51..acaacaa 100644
--- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt
@@ -7,6 +7,11 @@  this device needs phandles to the AUXADC. Also it controls a mux in the
 apmixedsys register space via AHB bus accesses, so a phandle to the APMIXEDSYS
 is also needed.
 
+There is another hardware engine, SVS (Smart Voltage Scaling) which shares the
+same block of banked registers with Mediatek thermal controller. Hence the
+driver of SVS is integrated with the driver of Mediatek thermal controller. The
+properties required by SVS engine are optional for Mediatek thermal controller.
+
 Required properties:
 - compatible: "mediatek,mt8173-thermal"
 - reg: Address range of the thermal controller
@@ -21,9 +26,15 @@  Required properties:
 - #thermal-sensor-cells : Should be 0. See ./thermal.txt for a description.
 
 Optional properties:
-- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If
-               unspecified default values shall be used.
-- nvmem-cell-names: Should be "calibration-data"
+- clocks, clock-names: Clocks that are optional for the thermal controller.
+	       Specify to enable SVS engine.
+	       "svs_pll": The PLL clock should be switched to during
+			  initialization stage of SVS engine.
+	       "svs_mux": The MUX clock controls the clock input of SVS engine.
+- nvmem-cells: A list of phandles to the calibration data provided by a nvmem
+	       device. If unspecified default values shall be used. The SVS
+	       engine will be disabled if no SVS calibration data is specified.
+- nvmem-cell-names: Should be "calibration-data" and "svs-calibration-data"
 
 Example:
 
@@ -33,11 +44,11 @@  Example:
 		reg = <0 0x1100b000 0 0x1000>;
 		interrupts = <0 70 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&pericfg CLK_PERI_THERM>, <&pericfg CLK_PERI_AUXADC>;
-		clock-names = "therm", "auxadc";
+		clock-names = "therm", "auxadc", ;
 		resets = <&pericfg MT8173_PERI_THERM_SW_RST>;
 		reset-names = "therm";
 		mediatek,auxadc = <&auxadc>;
 		mediatek,apmixedsys = <&apmixedsys>;
-		nvmem-cells = <&thermal_calibration_data>;
-		nvmem-cell-names = "calibration-data";
+		nvmem-cells = <&thermal_calibration_data>, <&svs-calibration>;
+		nvmem-cell-names = "calibration-data", "svs-calibration-data";
 	};