| Message ID | 20220718134458.19137-3-phil.edworthy@renesas.com |
|---|---|
| State | New |
| Headers | show |
| Series | Add usb gadget support for RZ/V2M | expand |
Hi Phil, On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy <phil.edworthy@renesas.com> wrote: > RZ/V2M (r9a09g011) has a few differences: > - The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON in > the RZ/V2M hardware manual. > It has additional bits for host and peripheral reset that need to > cleared to use usb host and peripheral respectively. > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers > have been moved and renamed to USB_PERI_DRD_STA, USB_PERI_DRD_INT_STA > and USB_PERI_DRD_INT_E. > - The IDMON bit used in the above regs for role detection have moved > from bit 4 to bit 0. > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to IDMON. > - There are reset lines for DRD and USBP > - There is another clock, managed by runtime PM. > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> Thanks for your patch! > --- a/drivers/usb/gadget/udc/renesas_usb3.c > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > @@ -363,6 +368,7 @@ struct renesas_usb3 { > bool forced_b_device; > bool start_to_connect; > bool role_sw_by_connector; > + bool r9a09g011; Any better name for this feature flag? > }; > @@ -2707,6 +2733,12 @@ static const struct renesas_usb3_priv renesas_usb3_priv_r8a77990 = { > .workaround_for_vbus = true, > }; > > +static const struct renesas_usb3_priv renesas_usb3_priv_r9a09g011 = { renesas_usb3_priv_rzv2m? > + .ramsize_per_ramif = SZ_32K, > + .num_ramif = 1, > + .ramsize_per_pipe = SZ_4K, > +}; > + > static const struct of_device_id usb3_of_match[] = { > { > .compatible = "renesas,r8a774c0-usb3-peri", > @@ -2717,6 +2749,9 @@ static const struct of_device_id usb3_of_match[] = { > }, { > .compatible = "renesas,r8a77990-usb3-peri", > .data = &renesas_usb3_priv_r8a77990, > + }, { > + .compatible = "renesas,r9a09g011-usb3-peri", As the bindings include a family-specific compatible value, you should use that ("renesas,rzv2m-usb3-peri") here. > + .data = &renesas_usb3_priv_r9a09g011, > }, { > .compatible = "renesas,rcar-gen3-usb3-peri", > .data = &renesas_usb3_priv_gen3, > @@ -2758,13 +2793,22 @@ static int renesas_usb3_probe(struct platform_device *pdev) > else > priv = of_device_get_match_data(&pdev->dev); > > + usb3 = devm_kzalloc(&pdev->dev, sizeof(*usb3), GFP_KERNEL); > + if (!usb3) > + return -ENOMEM; > + > + if (priv == &renesas_usb3_priv_r9a09g011) Please store the feature flag in renesas_usb3_priv instead of doing an explicit comparison. > + usb3->r9a09g011 = true; > + Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Hi Geert, Thanks for your review! On 21 July 2022 13:10 Geert Uytterhoeven wrote: > On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy wrote: > > RZ/V2M (r9a09g011) has a few differences: > > - The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON in > > the RZ/V2M hardware manual. > > It has additional bits for host and peripheral reset that need to > > cleared to use usb host and peripheral respectively. > > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers > > have been moved and renamed to USB_PERI_DRD_STA, USB_PERI_DRD_INT_STA > > and USB_PERI_DRD_INT_E. > > - The IDMON bit used in the above regs for role detection have moved > > from bit 4 to bit 0. > > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to IDMON. > > - There are reset lines for DRD and USBP > > - There is another clock, managed by runtime PM. > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> > > Thanks for your patch! > > > --- a/drivers/usb/gadget/udc/renesas_usb3.c > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > > > @@ -363,6 +368,7 @@ struct renesas_usb3 { > > bool forced_b_device; > > bool start_to_connect; > > bool role_sw_by_connector; > > + bool r9a09g011; > > Any better name for this feature flag? Nothing springs to mind. We could use separate flags for has_resets, has_drd_irq, max_nr_pipes but I am struggling to come up with names for the offset registers and moved bits. Any suggestions? > > }; > > > @@ -2707,6 +2733,12 @@ static const struct renesas_usb3_priv > renesas_usb3_priv_r8a77990 = { > > .workaround_for_vbus = true, > > }; > > > > +static const struct renesas_usb3_priv renesas_usb3_priv_r9a09g011 = { > > renesas_usb3_priv_rzv2m? Ok > > + .ramsize_per_ramif = SZ_32K, > > + .num_ramif = 1, > > + .ramsize_per_pipe = SZ_4K, > > +}; > > + > > static const struct of_device_id usb3_of_match[] = { > > { > > .compatible = "renesas,r8a774c0-usb3-peri", > > @@ -2717,6 +2749,9 @@ static const struct of_device_id usb3_of_match[] = > { > > }, { > > .compatible = "renesas,r8a77990-usb3-peri", > > .data = &renesas_usb3_priv_r8a77990, > > + }, { > > + .compatible = "renesas,r9a09g011-usb3-peri", > > As the bindings include a family-specific compatible value, you should > use that ("renesas,rzv2m-usb3-peri") here. Ok > > + .data = &renesas_usb3_priv_r9a09g011, > > }, { > > .compatible = "renesas,rcar-gen3-usb3-peri", > > .data = &renesas_usb3_priv_gen3, > > > @@ -2758,13 +2793,22 @@ static int renesas_usb3_probe(struct > platform_device *pdev) > > else > > priv = of_device_get_match_data(&pdev->dev); > > > > + usb3 = devm_kzalloc(&pdev->dev, sizeof(*usb3), GFP_KERNEL); > > + if (!usb3) > > + return -ENOMEM; > > + > > + if (priv == &renesas_usb3_priv_r9a09g011) > > Please store the feature flag in renesas_usb3_priv instead of doing an > explicit comparison. Ok, will do! > > + usb3->r9a09g011 = true; > > + Thanks Phil
Hi Phil, On Thu, Jul 21, 2022 at 2:25 PM Phil Edworthy <phil.edworthy@renesas.com> wrote: > On 21 July 2022 13:10 Geert Uytterhoeven wrote: > > On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy wrote: > > > RZ/V2M (r9a09g011) has a few differences: > > > - The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON in > > > the RZ/V2M hardware manual. > > > It has additional bits for host and peripheral reset that need to > > > cleared to use usb host and peripheral respectively. > > > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers > > > have been moved and renamed to USB_PERI_DRD_STA, USB_PERI_DRD_INT_STA > > > and USB_PERI_DRD_INT_E. > > > - The IDMON bit used in the above regs for role detection have moved > > > from bit 4 to bit 0. > > > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to IDMON. > > > - There are reset lines for DRD and USBP > > > - There is another clock, managed by runtime PM. > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> > > > > Thanks for your patch! > > > > > --- a/drivers/usb/gadget/udc/renesas_usb3.c > > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > > > > > @@ -363,6 +368,7 @@ struct renesas_usb3 { > > > bool forced_b_device; > > > bool start_to_connect; > > > bool role_sw_by_connector; > > > + bool r9a09g011; > > > > Any better name for this feature flag? > Nothing springs to mind. We could use separate flags for has_resets, > has_drd_irq, max_nr_pipes but I am struggling to come up with names > for the offset registers and moved bits. Any suggestions? OK, so "is_rzv2m"? Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds
Hi Geert, On 21 July 2022 13:43 Geert Uytterhoeven wrote: > On Thu, Jul 21, 2022 at 2:25 PM Phil Edworthy wrote: > > On 21 July 2022 13:10 Geert Uytterhoeven wrote: > > > On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy wrote: > > > > RZ/V2M (r9a09g011) has a few differences: > > > > - The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON > in > > > > the RZ/V2M hardware manual. > > > > It has additional bits for host and peripheral reset that need to > > > > cleared to use usb host and peripheral respectively. > > > > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers > > > > have been moved and renamed to USB_PERI_DRD_STA, > USB_PERI_DRD_INT_STA > > > > and USB_PERI_DRD_INT_E. > > > > - The IDMON bit used in the above regs for role detection have > moved > > > > from bit 4 to bit 0. > > > > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to > IDMON. > > > > - There are reset lines for DRD and USBP > > > > - There is another clock, managed by runtime PM. > > > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> > > > > > > Thanks for your patch! > > > > > > > --- a/drivers/usb/gadget/udc/renesas_usb3.c > > > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > > > > > > > @@ -363,6 +368,7 @@ struct renesas_usb3 { > > > > bool forced_b_device; > > > > bool start_to_connect; > > > > bool role_sw_by_connector; > > > > + bool r9a09g011; > > > > > > Any better name for this feature flag? > > Nothing springs to mind. We could use separate flags for has_resets, > > has_drd_irq, max_nr_pipes but I am struggling to come up with names > > for the offset registers and moved bits. Any suggestions? > > OK, so "is_rzv2m"? Ok! Thanks Phil
Hi Geert-san, Phil-san, Thank you for the patch! > From: Geert Uytterhoeven, Sent: Thursday, July 21, 2022 9:43 PM > > Hi Phil, > > On Thu, Jul 21, 2022 at 2:25 PM Phil Edworthy <phil.edworthy@renesas.com> wrote: > > On 21 July 2022 13:10 Geert Uytterhoeven wrote: > > > On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy wrote: > > > > RZ/V2M (r9a09g011) has a few differences: > > > > - The USB3_DRD_CON register has moved, its called USB_PERI_DRD_CON in > > > > the RZ/V2M hardware manual. > > > > It has additional bits for host and peripheral reset that need to > > > > cleared to use usb host and peripheral respectively. > > > > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA registers > > > > have been moved and renamed to USB_PERI_DRD_STA, USB_PERI_DRD_INT_STA > > > > and USB_PERI_DRD_INT_E. > > > > - The IDMON bit used in the above regs for role detection have moved > > > > from bit 4 to bit 0. > > > > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to IDMON. > > > > - There are reset lines for DRD and USBP > > > > - There is another clock, managed by runtime PM. > > > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> > > > > > > Thanks for your patch! > > > > > > > --- a/drivers/usb/gadget/udc/renesas_usb3.c > > > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > > > > > > > @@ -363,6 +368,7 @@ struct renesas_usb3 { > > > > bool forced_b_device; > > > > bool start_to_connect; > > > > bool role_sw_by_connector; > > > > + bool r9a09g011; > > > > > > Any better name for this feature flag? > > Nothing springs to mind. We could use separate flags for has_resets, > > has_drd_irq, max_nr_pipes but I am struggling to come up with names > > for the offset registers and moved bits. Any suggestions? > > OK, so "is_rzv2m"? The flag name looks good to me. However, I don't like the following usage in macros. --- -#define USB3_DRD_CON 0x218 +#define USB3_DRD_CON (usb3->r9a09g011 ? 0x400 : 0x218) ... -#define USB_OTG_IDMON BIT(4) +#define USB_OTG_IDMON (usb3->r9a09g011 ? BIT(0) : BIT(4)) ---- About registers' offset/bit, I think having specific members into a new struct is better like below. But, what do you think? struct renesas_usb3_reg { u16 drd_con_offset; ... u32 otg_idmon_bit; ... }; struct renesas_usb3 { ... struct renesas_usb3_reg regs; ... }; Best regards, Yoshihiro Shimoda
Hi Yoshihiro, On 21 July 2022 13:51 Yoshihiro Shimoda wrote: > > From: Geert Uytterhoeven, Sent: Thursday, July 21, 2022 9:43 PM > > On Thu, Jul 21, 2022 at 2:25 PM Phil Edworthy wrote: > > > On 21 July 2022 13:10 Geert Uytterhoeven wrote: > > > > On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy wrote: > > > > > RZ/V2M (r9a09g011) has a few differences: > > > > > - The USB3_DRD_CON register has moved, its called > USB_PERI_DRD_CON in > > > > > the RZ/V2M hardware manual. > > > > > It has additional bits for host and peripheral reset that need > to > > > > > cleared to use usb host and peripheral respectively. > > > > > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA > registers > > > > > have been moved and renamed to USB_PERI_DRD_STA, > USB_PERI_DRD_INT_STA > > > > > and USB_PERI_DRD_INT_E. > > > > > - The IDMON bit used in the above regs for role detection have > moved > > > > > from bit 4 to bit 0. > > > > > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to > IDMON. > > > > > - There are reset lines for DRD and USBP > > > > > - There is another clock, managed by runtime PM. > > > > > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> > > > > > > > > Thanks for your patch! > > > > > > > > > --- a/drivers/usb/gadget/udc/renesas_usb3.c > > > > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > > > > > > > > > @@ -363,6 +368,7 @@ struct renesas_usb3 { > > > > > bool forced_b_device; > > > > > bool start_to_connect; > > > > > bool role_sw_by_connector; > > > > > + bool r9a09g011; > > > > > > > > Any better name for this feature flag? > > > Nothing springs to mind. We could use separate flags for has_resets, > > > has_drd_irq, max_nr_pipes but I am struggling to come up with names > > > for the offset registers and moved bits. Any suggestions? > > > > OK, so "is_rzv2m"? > > The flag name looks good to me. However, I don't like the following usage > in macros. > --- > -#define USB3_DRD_CON 0x218 > +#define USB3_DRD_CON (usb3->r9a09g011 ? 0x400 : 0x218) > ... > -#define USB_OTG_IDMON BIT(4) > +#define USB_OTG_IDMON (usb3->r9a09g011 ? BIT(0) : BIT(4)) > ---- > > About registers' offset/bit, I think having specific members into > a new struct is better like below. But, what do you think? > > struct renesas_usb3_reg { > u16 drd_con_offset; > ... > u32 otg_idmon_bit; > ... > }; > > struct renesas_usb3 { > ... > struct renesas_usb3_reg regs; > ... > }; I think that might be a bit overly complex for the problem. How about: #define USB3_DRD_CON(p) ((p)->is_rzv2m ? 0x400 : 0x218) Thanks Phil
Hi Phil-san, > From: Phil Edworthy, Sent: Thursday, July 21, 2022 11:21 PM > > Hi Yoshihiro, > > On 21 July 2022 13:51 Yoshihiro Shimoda wrote: > > > From: Geert Uytterhoeven, Sent: Thursday, July 21, 2022 9:43 PM > > > On Thu, Jul 21, 2022 at 2:25 PM Phil Edworthy wrote: > > > > On 21 July 2022 13:10 Geert Uytterhoeven wrote: > > > > > On Mon, Jul 18, 2022 at 3:45 PM Phil Edworthy wrote: > > > > > > RZ/V2M (r9a09g011) has a few differences: > > > > > > - The USB3_DRD_CON register has moved, its called > > USB_PERI_DRD_CON in > > > > > > the RZ/V2M hardware manual. > > > > > > It has additional bits for host and peripheral reset that need > > to > > > > > > cleared to use usb host and peripheral respectively. > > > > > > - The USB3_OTG_STA, USB3_OTG_INT_STA and USB3_OTG_INT_ENA > > registers > > > > > > have been moved and renamed to USB_PERI_DRD_STA, > > USB_PERI_DRD_INT_STA > > > > > > and USB_PERI_DRD_INT_E. > > > > > > - The IDMON bit used in the above regs for role detection have > > moved > > > > > > from bit 4 to bit 0. > > > > > > - RZ/V2M has an separate interrupt for DRD, i.e. for changes to > > IDMON. > > > > > > - There are reset lines for DRD and USBP > > > > > > - There is another clock, managed by runtime PM. > > > > > > > > > > > > Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com> > > > > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com> > > > > > > > > > > Thanks for your patch! > > > > > > > > > > > --- a/drivers/usb/gadget/udc/renesas_usb3.c > > > > > > +++ b/drivers/usb/gadget/udc/renesas_usb3.c > > > > > > > > > > > @@ -363,6 +368,7 @@ struct renesas_usb3 { > > > > > > bool forced_b_device; > > > > > > bool start_to_connect; > > > > > > bool role_sw_by_connector; > > > > > > + bool r9a09g011; > > > > > > > > > > Any better name for this feature flag? > > > > Nothing springs to mind. We could use separate flags for has_resets, > > > > has_drd_irq, max_nr_pipes but I am struggling to come up with names > > > > for the offset registers and moved bits. Any suggestions? > > > > > > OK, so "is_rzv2m"? > > > > The flag name looks good to me. However, I don't like the following usage > > in macros. > > --- > > -#define USB3_DRD_CON 0x218 > > +#define USB3_DRD_CON (usb3->r9a09g011 ? 0x400 : 0x218) > > ... > > -#define USB_OTG_IDMON BIT(4) > > +#define USB_OTG_IDMON (usb3->r9a09g011 ? BIT(0) : BIT(4)) > > ---- > > > > About registers' offset/bit, I think having specific members into > > a new struct is better like below. But, what do you think? > > > > struct renesas_usb3_reg { > > u16 drd_con_offset; > > ... > > u32 otg_idmon_bit; > > ... > > }; > > > > struct renesas_usb3 { > > ... > > struct renesas_usb3_reg regs; > > ... > > }; > > I think that might be a bit overly complex for the problem. > How about: > #define USB3_DRD_CON(p) ((p)->is_rzv2m ? 0x400 : 0x218) Thank you for your suggestion. It looks good to me. Best regards, Yoshihiro Shimoda
diff --git a/drivers/usb/gadget/udc/renesas_usb3.c b/drivers/usb/gadget/udc/renesas_usb3.c index 648be3fd476a..ede2af06ac30 100644 --- a/drivers/usb/gadget/udc/renesas_usb3.c +++ b/drivers/usb/gadget/udc/renesas_usb3.c @@ -17,6 +17,7 @@ #include <linux/phy/phy.h> #include <linux/platform_device.h> #include <linux/pm_runtime.h> +#include <linux/reset.h> #include <linux/sizes.h> #include <linux/slab.h> #include <linux/string.h> @@ -38,16 +39,16 @@ #define USB3_USB20_CON 0x204 #define USB3_USB30_CON 0x208 #define USB3_USB_STA 0x210 -#define USB3_DRD_CON 0x218 +#define USB3_DRD_CON (usb3->r9a09g011 ? 0x400 : 0x218) #define USB3_USB_INT_STA_1 0x220 #define USB3_USB_INT_STA_2 0x224 #define USB3_USB_INT_ENA_1 0x228 #define USB3_USB_INT_ENA_2 0x22c #define USB3_STUP_DAT_0 0x230 #define USB3_STUP_DAT_1 0x234 -#define USB3_USB_OTG_STA 0x268 -#define USB3_USB_OTG_INT_STA 0x26c -#define USB3_USB_OTG_INT_ENA 0x270 +#define USB3_USB_OTG_STA (usb3->r9a09g011 ? 0x410 : 0x268) +#define USB3_USB_OTG_INT_STA (usb3->r9a09g011 ? 0x414 : 0x26c) +#define USB3_USB_OTG_INT_ENA (usb3->r9a09g011 ? 0x418 : 0x270) #define USB3_P0_MOD 0x280 #define USB3_P0_CON 0x288 #define USB3_P0_STA 0x28c @@ -135,6 +136,8 @@ #define USB_STA_VBUS_STA BIT(0) /* DRD_CON */ +#define DRD_CON_PERI_RST BIT(31) /* r9a09g011 only */ +#define DRD_CON_HOST_RST BIT(30) /* r9a09g011 only */ #define DRD_CON_PERI_CON BIT(24) #define DRD_CON_VBOUT BIT(0) @@ -155,7 +158,7 @@ #define USB_INT_2_PIPE(n) BIT(n) /* USB_OTG_STA, USB_OTG_INT_STA and USB_OTG_INT_ENA */ -#define USB_OTG_IDMON BIT(4) +#define USB_OTG_IDMON (usb3->r9a09g011 ? BIT(0) : BIT(4)) /* P0_MOD */ #define P0_MOD_DIR BIT(6) @@ -255,7 +258,7 @@ #define USB3_EP0_SS_MAX_PACKET_SIZE 512 #define USB3_EP0_HSFS_MAX_PACKET_SIZE 64 #define USB3_EP0_BUF_SIZE 8 -#define USB3_MAX_NUM_PIPES 6 /* This includes PIPE 0 */ +#define USB3_MAX_NUM_PIPES (usb3->r9a09g011 ? 9 : 6) /* This includes PIPE 0 */ #define USB3_WAIT_US 3 #define USB3_DMA_NUM_SETTING_AREA 4 /* @@ -330,6 +333,8 @@ struct renesas_usb3_priv { struct renesas_usb3 { void __iomem *reg; + struct reset_control *drd_rstc; + struct reset_control *usbp_rstc; struct usb_gadget gadget; struct usb_gadget_driver *driver; @@ -363,6 +368,7 @@ struct renesas_usb3 { bool forced_b_device; bool start_to_connect; bool role_sw_by_connector; + bool r9a09g011; }; #define gadget_to_renesas_usb3(_gadget) \ @@ -674,6 +680,13 @@ static void renesas_usb3_role_work(struct work_struct *work) static void usb3_set_mode(struct renesas_usb3 *usb3, bool host) { + if (usb3->r9a09g011) { + if (host) + usb3_clear_bit(usb3, DRD_CON_HOST_RST, USB3_DRD_CON); + else + usb3_clear_bit(usb3, DRD_CON_PERI_RST, USB3_DRD_CON); + } + if (host) usb3_clear_bit(usb3, DRD_CON_PERI_CON, USB3_DRD_CON); else @@ -2005,8 +2018,14 @@ static void usb3_irq_idmon_change(struct renesas_usb3 *usb3) usb3_check_id(usb3); } -static void usb3_irq_otg_int(struct renesas_usb3 *usb3, u32 otg_int_sta) +static void usb3_irq_otg_int(struct renesas_usb3 *usb3) { + u32 otg_int_sta = usb3_read(usb3, USB3_USB_OTG_INT_STA); + + otg_int_sta &= usb3_read(usb3, USB3_USB_OTG_INT_ENA); + if (otg_int_sta) + usb3_write(usb3, otg_int_sta, USB3_USB_OTG_INT_STA); + if (otg_int_sta & USB_OTG_IDMON) usb3_irq_idmon_change(usb3); } @@ -2015,7 +2034,6 @@ static void usb3_irq_epc(struct renesas_usb3 *usb3) { u32 int_sta_1 = usb3_read(usb3, USB3_USB_INT_STA_1); u32 int_sta_2 = usb3_read(usb3, USB3_USB_INT_STA_2); - u32 otg_int_sta = usb3_read(usb3, USB3_USB_OTG_INT_STA); int_sta_1 &= usb3_read(usb3, USB3_USB_INT_ENA_1); if (int_sta_1) { @@ -2027,11 +2045,8 @@ static void usb3_irq_epc(struct renesas_usb3 *usb3) if (int_sta_2) usb3_irq_epc_int_2(usb3, int_sta_2); - otg_int_sta &= usb3_read(usb3, USB3_USB_OTG_INT_ENA); - if (otg_int_sta) { - usb3_write(usb3, otg_int_sta, USB3_USB_OTG_INT_STA); - usb3_irq_otg_int(usb3, otg_int_sta); - } + if (!usb3->r9a09g011) + usb3_irq_otg_int(usb3); } static void usb3_irq_dma_int(struct renesas_usb3 *usb3, u32 dma_sta) @@ -2085,6 +2100,15 @@ static irqreturn_t renesas_usb3_irq(int irq, void *_usb3) return ret; } +static irqreturn_t renesas_usb3_otg_irq(int irq, void *_usb3) +{ + struct renesas_usb3 *usb3 = _usb3; + + usb3_irq_otg_int(usb3); + + return IRQ_HANDLED; +} + static void usb3_write_pn_mod(struct renesas_usb3_ep *usb3_ep, const struct usb_endpoint_descriptor *desc) { @@ -2571,6 +2595,8 @@ static int renesas_usb3_remove(struct platform_device *pdev) usb_role_switch_unregister(usb3->role_sw); usb_del_gadget_udc(&usb3->gadget); + reset_control_assert(usb3->usbp_rstc); + reset_control_assert(usb3->drd_rstc); renesas_usb3_dma_free_prd(usb3, &pdev->dev); __renesas_usb3_ep_free_request(usb3->ep0_req); @@ -2707,6 +2733,12 @@ static const struct renesas_usb3_priv renesas_usb3_priv_r8a77990 = { .workaround_for_vbus = true, }; +static const struct renesas_usb3_priv renesas_usb3_priv_r9a09g011 = { + .ramsize_per_ramif = SZ_32K, + .num_ramif = 1, + .ramsize_per_pipe = SZ_4K, +}; + static const struct of_device_id usb3_of_match[] = { { .compatible = "renesas,r8a774c0-usb3-peri", @@ -2717,6 +2749,9 @@ static const struct of_device_id usb3_of_match[] = { }, { .compatible = "renesas,r8a77990-usb3-peri", .data = &renesas_usb3_priv_r8a77990, + }, { + .compatible = "renesas,r9a09g011-usb3-peri", + .data = &renesas_usb3_priv_r9a09g011, }, { .compatible = "renesas,rcar-gen3-usb3-peri", .data = &renesas_usb3_priv_gen3, @@ -2748,7 +2783,7 @@ static struct usb_role_switch_desc renesas_usb3_role_switch_desc = { static int renesas_usb3_probe(struct platform_device *pdev) { struct renesas_usb3 *usb3; - int irq, ret; + int irq, drd_irq, ret; const struct renesas_usb3_priv *priv; const struct soc_device_attribute *attr; @@ -2758,13 +2793,22 @@ static int renesas_usb3_probe(struct platform_device *pdev) else priv = of_device_get_match_data(&pdev->dev); + usb3 = devm_kzalloc(&pdev->dev, sizeof(*usb3), GFP_KERNEL); + if (!usb3) + return -ENOMEM; + + if (priv == &renesas_usb3_priv_r9a09g011) + usb3->r9a09g011 = true; + irq = platform_get_irq(pdev, 0); if (irq < 0) return irq; - usb3 = devm_kzalloc(&pdev->dev, sizeof(*usb3), GFP_KERNEL); - if (!usb3) - return -ENOMEM; + if (usb3->r9a09g011) { + drd_irq = platform_get_irq_byname(pdev, "drd"); + if (drd_irq < 0) + return drd_irq; + } usb3->reg = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(usb3->reg)) @@ -2787,6 +2831,14 @@ static int renesas_usb3_probe(struct platform_device *pdev) if (ret < 0) return ret; + if (usb3->r9a09g011) { + ret = devm_request_irq(&pdev->dev, drd_irq, + renesas_usb3_otg_irq, 0, + dev_name(&pdev->dev), usb3); + if (ret < 0) + return ret; + } + INIT_WORK(&usb3->extcon_work, renesas_usb3_extcon_work); usb3->extcon = devm_extcon_dev_allocate(&pdev->dev, renesas_usb3_cable); if (IS_ERR(usb3->extcon)) @@ -2817,10 +2869,27 @@ static int renesas_usb3_probe(struct platform_device *pdev) goto err_add_udc; } + usb3->drd_rstc = devm_reset_control_get_optional_shared(&pdev->dev, + "drd_reset"); + if (IS_ERR(usb3->drd_rstc)) { + ret = PTR_ERR(usb3->drd_rstc); + goto err_add_udc; + } + + usb3->usbp_rstc = devm_reset_control_get_optional_shared(&pdev->dev, + "aresetn_p"); + if (IS_ERR(usb3->usbp_rstc)) { + ret = PTR_ERR(usb3->usbp_rstc); + goto err_add_udc; + } + + reset_control_deassert(usb3->drd_rstc); + reset_control_deassert(usb3->usbp_rstc); + pm_runtime_enable(&pdev->dev); ret = usb_add_gadget_udc(&pdev->dev, &usb3->gadget); if (ret < 0) - goto err_add_udc; + goto err_reset; ret = device_create_file(&pdev->dev, &dev_attr_role); if (ret < 0) @@ -2858,6 +2927,10 @@ static int renesas_usb3_probe(struct platform_device *pdev) err_dev_create: usb_del_gadget_udc(&usb3->gadget); +err_reset: + reset_control_assert(usb3->usbp_rstc); + reset_control_assert(usb3->drd_rstc); + err_add_udc: renesas_usb3_dma_free_prd(usb3, &pdev->dev);