diff mbox series

[v3] serial: 8250_dw: Avoid pslverr on reading empty receiver fifo

Message ID 20220713131722.2316829-1-vamshigajjela@google.com
State New
Headers show
Series [v3] serial: 8250_dw: Avoid pslverr on reading empty receiver fifo | expand

Commit Message

Vamshi Gajjela July 13, 2022, 1:17 p.m. UTC 
From: VAMSHI GAJJELA <vamshigajjela@google.com>

With PSLVERR_RESP_EN parameter set to 1, the device generates an error
response when an attempt to read an empty RBR with FIFO enabled.

This happens when LCR writes are ignored when UART is busy.
dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
to clear and reset FIFO and eventually reads UART_RX causing the error.

Avoid this by not reading RBR/UART_RX when no data is available.

Signed-off-by: VAMSHI GAJJELA <vamshigajjela@google.com>
---
v3:
- check lsr based on FIFO enablement
v2:
- update as per review comments (re-format comments, xmas tree ordering)
 drivers/tty/serial/8250/8250_dw.c | 13 +++++++++++++
 1 file changed, 13 insertions(+)

Comments

Andy Shevchenko July 13, 2022, 4:11 p.m. UTC | #1 
On Wed, Jul 13, 2022 at 06:47:22PM +0530, Vamshi Gajjela wrote:
> From: VAMSHI GAJJELA <vamshigajjela@google.com>
> 
> With PSLVERR_RESP_EN parameter set to 1, the device generates an error
> response when an attempt to read an empty RBR with FIFO enabled.
> 
> This happens when LCR writes are ignored when UART is busy.
> dw8250_check_lcr() in retries to update LCR, invokes dw8250_force_idle()
> to clear and reset FIFO and eventually reads UART_RX causing the error.
> 
> Avoid this by not reading RBR/UART_RX when no data is available.
diff mbox series

Patch

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index f57bbd32ef11..7573904579f6 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -82,8 +82,21 @@  static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value)
 static void dw8250_force_idle(struct uart_port *p)
 {
 	struct uart_8250_port *up = up_to_u8250p(p);
+	unsigned int lsr;
 
 	serial8250_clear_and_reinit_fifos(up);
+
+	/*
+	 * With PSLVERR_RESP_EN parameter set to 1, the device generates an
+	 * error response when an attempt to read an empty RBR with FIFO
+	 * enabled.
+	 */
+	if (up->fcr & UART_FCR_ENABLE_FIFO) {
+		lsr = p->serial_in(p, UART_LSR);
+		if (!(lsr & UART_LSR_DR))
+			return;
+	}
+
 	(void)p->serial_in(p, UART_RX);
 }