@@ -193,6 +193,7 @@ extern void device_links_no_driver(struct device *dev);
extern bool device_links_busy(struct device *dev);
extern void device_links_unbind_consumers(struct device *dev);
extern void fw_devlink_drivers_done(void);
+extern void fw_devlink_probe_no_timeout(void);
/* device pm support */
void device_pm_move_to_tail(struct device *dev);
@@ -54,6 +54,7 @@ static unsigned int defer_sync_state_count = 1;
static DEFINE_MUTEX(fwnode_link_lock);
static bool fw_devlink_is_permissive(void);
static bool fw_devlink_drv_reg_done;
+static bool fw_devlink_no_timeout;
static bool fw_devlink_best_effort;
/**
@@ -969,6 +970,7 @@ static void device_links_missing_supplier(struct device *dev)
static bool dev_is_best_effort(struct device *dev)
{
return (fw_devlink_best_effort && dev->can_match) ||
+ (fw_devlink_no_timeout && dev->probe_no_timeout) ||
(dev->fwnode && (dev->fwnode->flags & FWNODE_FLAG_BEST_EFFORT));
}
@@ -1688,6 +1690,11 @@ void fw_devlink_drivers_done(void)
device_links_write_unlock();
}
+void fw_devlink_probe_no_timeout(void)
+{
+ fw_devlink_no_timeout = true;
+}
+
/**
* wait_for_init_devices_probe - Try to probe any device needed for init
*
@@ -324,6 +324,8 @@ static int deferred_probe_initcall(void)
if (!IS_ENABLED(CONFIG_MODULES))
fw_devlink_drivers_done();
+ else
+ fw_devlink_probe_no_timeout();
/*
* Trigger deferred probe again, this time we won't defer anything
@@ -734,6 +736,7 @@ static int __driver_probe_device(struct device_driver *drv, struct device *dev)
return -EBUSY;
dev->can_match = true;
+ dev->probe_no_timeout = drv->probe_no_timeout;
pr_debug("bus: '%s': %s: matched device %s with driver %s\n",
drv->bus->name, __func__, dev_name(dev), drv->name);
@@ -536,6 +536,12 @@ struct device_physical_location {
* @can_match: The device has matched with a driver at least once or it is in
* a bus (like AMBA) which can't check for matching drivers until
* other devices probe successfully.
+ * @probe_no_timeout: Set by driver core to indicate that this device's probe
+ * can't wait till driver_probe_timeout expires. This information
+ * is used by fw_devlink=on to avoid deferring the probe of this
+ * device to wait on supplier devices that haven't been added or
+ * probed successfully.
+ * See also: probe_no_timeout in struct driver.
* @dma_coherent: this particular device is dma coherent, even if the
* architecture supports non-coherent devices.
* @dma_ops_bypass: If set to %true then the dma_ops are bypassed for the
@@ -642,6 +648,7 @@ struct device {
bool of_node_reused:1;
bool state_synced:1;
bool can_match:1;
+ bool probe_no_timeout:1;
#if defined(CONFIG_ARCH_HAS_SYNC_DMA_FOR_DEVICE) || \
defined(CONFIG_ARCH_HAS_SYNC_DMA_FOR_CPU) || \
defined(CONFIG_ARCH_HAS_SYNC_DMA_FOR_CPU_ALL)
@@ -55,6 +55,15 @@ enum probe_type {
* @owner: The module owner.
* @mod_name: Used for built-in modules.
* @suppress_bind_attrs: Disables bind/unbind via sysfs.
+ * @probe_no_timeout: Set to true by drivers that bind to devices that meet all
+ * these conditions:
+ * - Need to probe successfully before userspace init in started
+ * - Have optional suppliers
+ * - Can't wait for deferred_probe_timeout to expire
+ * fw_devlink=on uses this info, as needed, to ignore dependencies
+ * on supplier devices that have not been added or supplier devices
+ * that don't have any drivers. It's still up to the driver to
+ * decide which of the missing suppliers are optional or not.
* @probe_type: Type of the probe (synchronous or asynchronous) to use.
* @of_match_table: The open firmware table.
* @acpi_match_table: The ACPI match table.
@@ -101,6 +110,8 @@ struct device_driver {
const char *mod_name; /* used for built-in modules */
bool suppress_bind_attrs; /* disables bind/unbind via sysfs */
+ bool probe_no_timeout;
+
enum probe_type probe_type;
const struct of_device_id *of_match_table;
This flag only needs to be set for drivers of devices that meet all the following conditions: - Need to probe successfully before userspace init in started - Have optional suppliers - Can't wait for deferred_probe_timeout to expire fw_devlink=on uses this info, as needed, to ignore dependencies on supplier devices that have not been added or supplier devices that don't have any drivers. It's still up to the driver to decide which of the missing suppliers are optional or not. Fixes: 71066545b48e ("driver core: Set fw_devlink.strict=1 by default") Reported-by: Sascha Hauer <sha@pengutronix.de> Reported-by: Peng Fan <peng.fan@nxp.com> Reported-by: Fabio Estevam <festevam@gmail.com> Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Saravana Kannan <saravanak@google.com> --- drivers/base/base.h | 1 + drivers/base/core.c | 7 +++++++ drivers/base/dd.c | 3 +++ include/linux/device.h | 7 +++++++ include/linux/device/driver.h | 11 +++++++++++ 5 files changed, 29 insertions(+)