diff mbox series

[v5,1/3] mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages

Message ID 20220608001030.18813-2-ansuelsmth@gmail.com
State New
Headers show
Series Add support for unprotected spare data page | expand

Commit Message

Christian Marangi June 8, 2022, 12:10 a.m. UTC
IPQ8064 nand have special pages where a different layout scheme is used.
These special page are used by boot partition and on reading them
lots of warning are reported about wrong ECC data and if written to
results in broken data and not bootable device.

The layout scheme used by these special page consist in using 512 bytes
as the codeword size (even for the last codeword) while writing to CFG0
register. This forces the NAND controller to unprotect the 4 bytes of
spare data.

Since the kernel is unaware of this different layout for these special
page, it does try to protect the spare data too during read/write and
warn about CRC errors.

Add support for this by permitting the user to declare these special
pages in dts by declaring offset and size of the partition. The driver
internally will convert these value to nand pages.

On user read/write the page is checked and if it's a boot page the
correct layout is used.

Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
 drivers/mtd/nand/raw/qcom_nandc.c | 174 +++++++++++++++++++++++++++++-
 1 file changed, 169 insertions(+), 5 deletions(-)

Comments

Manivannan Sadhasivam June 9, 2022, 7:52 a.m. UTC | #1
On Wed, Jun 08, 2022 at 02:10:28AM +0200, Ansuel Smith wrote:
> IPQ8064 nand have special pages where a different layout scheme is used.
> These special page are used by boot partition and on reading them
> lots of warning are reported about wrong ECC data and if written to
> results in broken data and not bootable device.
> 
> The layout scheme used by these special page consist in using 512 bytes
> as the codeword size (even for the last codeword) while writing to CFG0
> register. This forces the NAND controller to unprotect the 4 bytes of
> spare data.
> 
> Since the kernel is unaware of this different layout for these special
> page, it does try to protect the spare data too during read/write and
> warn about CRC errors.
> 
> Add support for this by permitting the user to declare these special
> pages in dts by declaring offset and size of the partition. The driver
> internally will convert these value to nand pages.
> 
> On user read/write the page is checked and if it's a boot page the
> correct layout is used.
> 
> Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> ---
>  drivers/mtd/nand/raw/qcom_nandc.c | 174 +++++++++++++++++++++++++++++-
>  1 file changed, 169 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
> index 1a77542c6d67..06ee9a836a3b 100644
> --- a/drivers/mtd/nand/raw/qcom_nandc.c
> +++ b/drivers/mtd/nand/raw/qcom_nandc.c
> @@ -80,8 +80,10 @@
>  #define	DISABLE_STATUS_AFTER_WRITE	4
>  #define	CW_PER_PAGE			6
>  #define	UD_SIZE_BYTES			9
> +#define	UD_SIZE_BYTES_MASK		GENMASK(18, 9)
>  #define	ECC_PARITY_SIZE_BYTES_RS	19
>  #define	SPARE_SIZE_BYTES		23
> +#define	SPARE_SIZE_BYTES_MASK		GENMASK(26, 23)
>  #define	NUM_ADDR_CYCLES			27
>  #define	STATUS_BFR_READ			30
>  #define	SET_RD_MODE_AFTER_STATUS	31
> @@ -102,6 +104,7 @@
>  #define	ECC_MODE			4
>  #define	ECC_PARITY_SIZE_BYTES_BCH	8
>  #define	ECC_NUM_DATA_BYTES		16
> +#define	ECC_NUM_DATA_BYTES_MASK		GENMASK(25, 16)
>  #define	ECC_FORCE_CLK_OPEN		30
>  
>  /* NAND_DEV_CMD1 bits */
> @@ -418,6 +421,19 @@ struct qcom_nand_controller {
>  	const struct qcom_nandc_props *props;
>  };
>  
> +/*
> + * NAND special boot partitions
> + *
> + * @page_offset:		offset of the partition where spare data is not protected
> + *				by ECC (value in pages)

s/page_offset/offset

> + * @page_offset:		size of the partition where spare data is not protected
> + *				by ECC (value in pages)

s/page_offset/size

> + */
> +struct qcom_nand_boot_partition {
> +	u32 page_offset;
> +	u32 page_size;

same here

> +};
> +
>  /*
>   * NAND chip structure
>   *
> @@ -444,6 +460,13 @@ struct qcom_nand_controller {
>   * @cfg0, cfg1, cfg0_raw..:	NANDc register configurations needed for
>   *				ecc/non-ecc mode for the current nand flash
>   *				device
> + *
> + * @codeword_fixup:		keep track of the current layout used by
> + *				the driver for read/write operation.
> + * @nr_boot_partitions:		count of the boot partitions where spare data is not
> + *				protected by ECC

Align the Kdoc comments w.r.t other members.

> + * @boot_pages:			array of boot partitions where offset and size of the
> + *				boot partitions are stored

s/boot_pages/boot_partitions

>   */
>  struct qcom_nand_host {
>  	struct nand_chip chip;
> @@ -466,6 +489,10 @@ struct qcom_nand_host {
>  	u32 ecc_bch_cfg;
>  	u32 clrflashstatus;
>  	u32 clrreadstatus;
> +
> +	bool codeword_fixup;
> +	int nr_boot_partitions;
> +	struct qcom_nand_boot_partition *boot_partitions;
>  };
>  
>  /*
> @@ -475,6 +502,7 @@ struct qcom_nand_host {
>   * @is_bam - whether NAND controller is using BAM
>   * @is_qpic - whether NAND CTRL is part of qpic IP
>   * @qpic_v2 - flag to indicate QPIC IP version 2
> + * @use_codeword_fixup - whether NAND has different layout for boot partitions
>   * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset
>   */
>  struct qcom_nandc_props {
> @@ -482,6 +510,7 @@ struct qcom_nandc_props {
>  	bool is_bam;
>  	bool is_qpic;
>  	bool qpic_v2;
> +	bool use_codeword_fixup;
>  	u32 dev_cmd_reg_start;
>  };
>  
> @@ -1701,7 +1730,7 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip,
>  	data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
>  	oob_size1 = host->bbm_size;
>  
> -	if (qcom_nandc_is_last_cw(ecc, cw)) {
> +	if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) {
>  		data_size2 = ecc->size - data_size1 -
>  			     ((ecc->steps - 1) * 4);
>  		oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw +
> @@ -1782,7 +1811,7 @@ check_for_erased_page(struct qcom_nand_host *host, u8 *data_buf,
>  	}
>  
>  	for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) {
> -		if (qcom_nandc_is_last_cw(ecc, cw)) {
> +		if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) {
>  			data_size = ecc->size - ((ecc->steps - 1) * 4);
>  			oob_size = (ecc->steps * 4) + host->ecc_bytes_hw;
>  		} else {
> @@ -1940,7 +1969,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,
>  	for (i = 0; i < ecc->steps; i++) {
>  		int data_size, oob_size;
>  
> -		if (qcom_nandc_is_last_cw(ecc, i)) {
> +		if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) {
>  			data_size = ecc->size - ((ecc->steps - 1) << 2);
>  			oob_size = (ecc->steps << 2) + host->ecc_bytes_hw +
>  				   host->spare_bytes;
> @@ -2037,6 +2066,55 @@ static int copy_last_cw(struct qcom_nand_host *host, int page)
>  	return ret;
>  }
>  
> +static bool
> +qcom_nandc_is_boot_page(struct qcom_nand_host *host, int page)

Move function name to previous line. If it exceeds 100 lines then wrap
arguments.

s/qcom_nandc_is_boot_page/qcom_nandc_is_boot_partition

> +{
> +	struct qcom_nand_boot_partition *boot_partition;
> +	u32 start, end;
> +	int i;
> +
> +	for (i = 0; i < host->nr_boot_partitions; i++) {
> +		boot_partition = &host->boot_partitions[i];
> +		start = boot_partition->page_offset;
> +		end = start + boot_partition->page_size;
> +
> +		/* Boot pages are normally at the start of

Block comments should start with:

	/*
	 * ...

Also, are you sure that only few pages in the partitions have different layout
and not all pages? If not, then this comment needs to be reworded.

> +		 * the nand in various partition.
> +		 * Check the page from the boot page end first
> +		 * to save one extra check and optimize this
> +		 * in case real no-boot partition are used.
> +		 */
> +		if (page < end && page >= start)
> +			return true;
> +	}
> +
> +	return false;
> +}
> +
> +static void
> +qcom_nandc_codeword_fixup(struct qcom_nand_host *host, int page)
> +{
> +	bool codeword_fixup = qcom_nandc_is_boot_page(host, page);
> +
> +	/* Skip conf write if we are already in the correct mode */
> +	if (codeword_fixup == host->codeword_fixup)
> +		return;
> +
> +	host->codeword_fixup = codeword_fixup;
> +
> +	host->cw_data = codeword_fixup ? 512 : 516;
> +	host->spare_bytes = host->cw_size - host->ecc_bytes_hw -
> +			    host->bbm_size - host->cw_data;
> +
> +	host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK);
> +	host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES |
> +		      host->cw_data << UD_SIZE_BYTES;
> +
> +	host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK;
> +	host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES;
> +	host->ecc_buf_cfg = (codeword_fixup ? 0x1ff : 0x203) << NUM_STEPS;

s/1ff/(512 - 1)
s/203/(516 - 1)

> +}
> +
>  /* implements ecc->read_page() */
>  static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf,
>  				int oob_required, int page)
> @@ -2045,6 +2123,9 @@ static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf,
>  	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
>  	u8 *data_buf, *oob_buf = NULL;
>  
> +	if (host->nr_boot_partitions)
> +		qcom_nandc_codeword_fixup(host, page);
> +
>  	nand_read_page_op(chip, page, 0, NULL, 0);
>  	data_buf = buf;
>  	oob_buf = oob_required ? chip->oob_poi : NULL;
> @@ -2064,6 +2145,9 @@ static int qcom_nandc_read_page_raw(struct nand_chip *chip, uint8_t *buf,
>  	int cw, ret;
>  	u8 *data_buf = buf, *oob_buf = chip->oob_poi;
>  
> +	if (host->nr_boot_partitions)
> +		qcom_nandc_codeword_fixup(host, page);
> +
>  	for (cw = 0; cw < ecc->steps; cw++) {
>  		ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf,
>  					     page, cw);
> @@ -2084,6 +2168,9 @@ static int qcom_nandc_read_oob(struct nand_chip *chip, int page)
>  	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
>  	struct nand_ecc_ctrl *ecc = &chip->ecc;
>  
> +	if (host->nr_boot_partitions)
> +		qcom_nandc_codeword_fixup(host, page);
> +
>  	clear_read_regs(nandc);
>  	clear_bam_transaction(nandc);
>  
> @@ -2104,6 +2191,9 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf,
>  	u8 *data_buf, *oob_buf;
>  	int i, ret;
>  
> +	if (host->nr_boot_partitions)
> +		qcom_nandc_codeword_fixup(host, page);
> +
>  	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
>  
>  	clear_read_regs(nandc);
> @@ -2119,7 +2209,7 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf,
>  	for (i = 0; i < ecc->steps; i++) {
>  		int data_size, oob_size;
>  
> -		if (qcom_nandc_is_last_cw(ecc, i)) {
> +		if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) {
>  			data_size = ecc->size - ((ecc->steps - 1) << 2);
>  			oob_size = (ecc->steps << 2) + host->ecc_bytes_hw +
>  				   host->spare_bytes;
> @@ -2176,6 +2266,9 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip,
>  	u8 *data_buf, *oob_buf;
>  	int i, ret;
>  
> +	if (host->nr_boot_partitions)
> +		qcom_nandc_codeword_fixup(host, page);
> +
>  	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
>  	clear_read_regs(nandc);
>  	clear_bam_transaction(nandc);
> @@ -2194,7 +2287,7 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip,
>  		data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
>  		oob_size1 = host->bbm_size;
>  
> -		if (qcom_nandc_is_last_cw(ecc, i)) {
> +		if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) {
>  			data_size2 = ecc->size - data_size1 -
>  				     ((ecc->steps - 1) << 2);
>  			oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw +
> @@ -2254,6 +2347,9 @@ static int qcom_nandc_write_oob(struct nand_chip *chip, int page)
>  	int data_size, oob_size;
>  	int ret;
>  
> +	if (host->nr_boot_partitions)
> +		qcom_nandc_codeword_fixup(host, page);
> +
>  	host->use_ecc = true;
>  	clear_bam_transaction(nandc);
>  
> @@ -2902,6 +2998,71 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc)
>  
>  static const char * const probes[] = { "cmdlinepart", "ofpart", "qcomsmem", NULL };
>  
> +static int qcom_nand_host_parse_boot_partitions(struct qcom_nand_controller *nandc,
> +						struct qcom_nand_host *host,
> +						struct device_node *dn)
> +{
> +	struct nand_chip *chip = &host->chip;
> +	struct mtd_info *mtd = nand_to_mtd(chip);
> +	struct qcom_nand_boot_partition *boot_partition;
> +	struct device *dev = nandc->dev;
> +	int partitions_count, i, j, ret;
> +
> +	if (!nandc->props->use_codeword_fixup)
> +		return 0;

Move this check to caller as I suggested previously.

> +
> +	if (!of_find_property(dn, "qcom,boot-partitions", NULL))
> +		return 0;
> +
> +	partitions_count = of_property_count_u32_elems(dn, "qcom,boot-partitions");
> +	if (partitions_count < 0) {

partitions_count <= 0

> +		dev_err(dev, "Error parsing boot partition.");

Add newline at the end of error message

> +		return ret;
> +	}
> +
> +	host->nr_boot_partitions = partitions_count / 2;
> +	host->boot_partitions = devm_kcalloc(dev, host->nr_boot_partitions,
> +					     sizeof(*host->boot_partitions), GFP_KERNEL);
> +	if (!host->boot_partitions)

host->nr_boot_partitions = 0;

> +		return -ENOMEM;
> +
> +	for (i = 0, j = 0; i < host->nr_boot_partitions; i++, j += 2) {
> +		boot_partition = &host->boot_partitions[i];
> +
> +		ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j,
> +						 &boot_partition->page_offset);
> +		if (ret) {
> +			dev_err(dev, "Error parsing boot partition offset at index %d", i);

Add newline at the end of error message. Do the same for all error prints.

> +			return ret;
> +		}
> +
> +		if (boot_partition->page_offset % mtd->writesize) {
> +			dev_err(dev, "Boot partition offset not multiple of writesize at index %i",
> +				i);
> +			return -EINVAL;
> +		}
> +		/* Convert offset to nand pages */

s/pages/partitions

> +		boot_partition->page_offset /= mtd->writesize;

s/page_offset/offset

> +
> +		ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j + 1,
> +						 &boot_partition->page_size);
> +		if (ret) {
> +			dev_err(dev, "Error parsing boot partition size at index %d", i);
> +			return ret;
> +		}
> +
> +		if (boot_partition->page_size % mtd->writesize) {

s/page_size/size here and below

> +			dev_err(dev, "Boot partition size not multiple of writesize at index %i",
> +				i);
> +			return -EINVAL;
> +		}
> +		/* Convert size to nand pages */

s/pages/partitions

Thanks,
Mani

> +		boot_partition->page_size /= mtd->writesize;
> +	}
> +
> +	return 0;
> +}
> +
>  static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc,
>  					    struct qcom_nand_host *host,
>  					    struct device_node *dn)
> @@ -2970,6 +3131,8 @@ static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc,
>  	if (ret)
>  		nand_cleanup(chip);
>  
> +	qcom_nand_host_parse_boot_partitions(nandc, host, dn);
> +
>  	return ret;
>  }
>  
> @@ -3135,6 +3298,7 @@ static int qcom_nandc_remove(struct platform_device *pdev)
>  static const struct qcom_nandc_props ipq806x_nandc_props = {
>  	.ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT),
>  	.is_bam = false,
> +	.use_codeword_fixup = true,
>  	.dev_cmd_reg_start = 0x0,
>  };
>  
> -- 
> 2.36.1
>
Manivannan Sadhasivam June 9, 2022, 11:16 a.m. UTC | #2
On Thu, Jun 09, 2022 at 12:24:22PM +0200, Ansuel Smith wrote:
> On Thu, Jun 09, 2022 at 01:22:54PM +0530, Manivannan Sadhasivam wrote:
> > On Wed, Jun 08, 2022 at 02:10:28AM +0200, Ansuel Smith wrote:
> > > IPQ8064 nand have special pages where a different layout scheme is used.
> > > These special page are used by boot partition and on reading them
> > > lots of warning are reported about wrong ECC data and if written to
> > > results in broken data and not bootable device.
> > > 
> > > The layout scheme used by these special page consist in using 512 bytes
> > > as the codeword size (even for the last codeword) while writing to CFG0
> > > register. This forces the NAND controller to unprotect the 4 bytes of
> > > spare data.
> > > 
> > > Since the kernel is unaware of this different layout for these special
> > > page, it does try to protect the spare data too during read/write and
> > > warn about CRC errors.
> > > 
> > > Add support for this by permitting the user to declare these special
> > > pages in dts by declaring offset and size of the partition. The driver
> > > internally will convert these value to nand pages.
> > > 
> > > On user read/write the page is checked and if it's a boot page the
> > > correct layout is used.
> > > 
> > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
> > > ---
> > >  drivers/mtd/nand/raw/qcom_nandc.c | 174 +++++++++++++++++++++++++++++-
> > >  1 file changed, 169 insertions(+), 5 deletions(-)
> > > 
> > > diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
> > > index 1a77542c6d67..06ee9a836a3b 100644
> > > --- a/drivers/mtd/nand/raw/qcom_nandc.c
> > > +++ b/drivers/mtd/nand/raw/qcom_nandc.c
> > > @@ -80,8 +80,10 @@
> > >  #define	DISABLE_STATUS_AFTER_WRITE	4
> > >  #define	CW_PER_PAGE			6
> > >  #define	UD_SIZE_BYTES			9
> > > +#define	UD_SIZE_BYTES_MASK		GENMASK(18, 9)
> > >  #define	ECC_PARITY_SIZE_BYTES_RS	19
> > >  #define	SPARE_SIZE_BYTES		23
> > > +#define	SPARE_SIZE_BYTES_MASK		GENMASK(26, 23)
> > >  #define	NUM_ADDR_CYCLES			27
> > >  #define	STATUS_BFR_READ			30
> > >  #define	SET_RD_MODE_AFTER_STATUS	31
> > > @@ -102,6 +104,7 @@
> > >  #define	ECC_MODE			4
> > >  #define	ECC_PARITY_SIZE_BYTES_BCH	8
> > >  #define	ECC_NUM_DATA_BYTES		16
> > > +#define	ECC_NUM_DATA_BYTES_MASK		GENMASK(25, 16)
> > >  #define	ECC_FORCE_CLK_OPEN		30
> > >  
> > >  /* NAND_DEV_CMD1 bits */
> > > @@ -418,6 +421,19 @@ struct qcom_nand_controller {
> > >  	const struct qcom_nandc_props *props;
> > >  };
> > >  
> > > +/*
> > > + * NAND special boot partitions
> > > + *
> > > + * @page_offset:		offset of the partition where spare data is not protected
> > > + *				by ECC (value in pages)
> > 
> > s/page_offset/offset
> >
> 
> Mhhh i changed this to page_offset since the struct is called
> boot_partition and it can be confusing since internally the values is in
> pages. Someone can think that the real partition offset/size is used
> instead of the value converted in pages.

Hmm, okay.

> 
> > > + * @page_offset:		size of the partition where spare data is not protected
> > > + *				by ECC (value in pages)
> > 

[...]

> > > +static bool
> > > +qcom_nandc_is_boot_page(struct qcom_nand_host *host, int page)
> > 
> > Move function name to previous line. If it exceeds 100 lines then wrap
> > arguments.
> > 
> > s/qcom_nandc_is_boot_page/qcom_nandc_is_boot_partition
> > 
> 
> Again considering the check is done on the page and not on the
> partition, wonder what is correct.
> 

But the end goal is to detect if the page belongs to boot partitionis, right?

Also, mixing up boot_pages and boot_partitions is confusing. Let's stick to the
fact that this patch checks for pages belonging to the boot partition.

> > > +{
> > > +	struct qcom_nand_boot_partition *boot_partition;
> > > +	u32 start, end;
> > > +	int i;
> > > +
> > > +	for (i = 0; i < host->nr_boot_partitions; i++) {
> > > +		boot_partition = &host->boot_partitions[i];
> > > +		start = boot_partition->page_offset;
> > > +		end = start + boot_partition->page_size;
> > > +
> > > +		/* Boot pages are normally at the start of
> > 
> > Block comments should start with:
> > 
> > 	/*
> > 	 * ...
> > 
> > Also, are you sure that only few pages in the partitions have different layout
> > and not all pages? If not, then this comment needs to be reworded.
> > 
> 
> I probably worderd this bad...
> Each page of the boot partitions require the codeword fix.
> But other may have the normal codeword
> For example this is from a Netgear router:
> mtd0: 00c80000 00020000 "qcadata" (require codeword fix)
> mtd1: 00500000 00020000 "APPSBL"  (require codeword fix)
> mtd2: 00080000 00020000 "APPSBLENV" (doesn't require codeword fix)
> mtd3: 00140000 00020000 "art"       (doesn't)
> mtd4: 00140000 00020000 "artbak"    (doesn't)
> mtd5: 00400000 00020000 "kernel"    (doesn't)
> mtd6: 06080000 00020000 "ubi"       (doesn't)
> mtd7: 00700000 00020000 "reserve"   (doesn't)
> 
> This is part of the case tho as there are some partition table with
> something like
> 
> mtd0: 00c80000 00020000 "qcadata" (require codeword fix)
> mtd1: 00500000 00020000 "APPSBL"  (require codeword fix)
> mtd2: 00080000 00020000 "APPSBLENV" (doesn't require codeword fix)
> mtd3: 00140000 00020000 "APPSBL2"  (require codeword fix)
> [...]
> 
> In all case 99% of the time in a normal system what you commonly write
> are the rootfs partition that are AFTER the boot partition so checking
> if the page is after such partition should speed up the check.

This should be included in the comment.

> Now that I think about it, a good idea is also start checking the
> boot_partition table from the end to improve the checking even more.
> 

Yes and if the page lies after last boot partition then we can bail out in the
first iteration itself. But the binding should make it clear that the offset
should be specified in ascending order.

> So tell me if the comments is wronlgy worded.
> 

Based on the above algorithm:

/*
 * Since the frequent access will be to the non-boot partitions like rootfs,
 * optimize the page check by:

 * 1. Checking if the page lies after the last boot partition.
 * 2. Checking from the boot partition end.
 */

> > > +		 * the nand in various partition.
> > > +		 * Check the page from the boot page end first
> > > +		 * to save one extra check and optimize this
> > > +		 * in case real no-boot partition are used.
> > > +		 */
> > > +		if (page < end && page >= start)
> > > +			return true;
> > > +	}
> > > +
> > > +	return false;
> > > +}
> > > +
> > > +static void
> > > +qcom_nandc_codeword_fixup(struct qcom_nand_host *host, int page)
> > > +{
> > > +	bool codeword_fixup = qcom_nandc_is_boot_page(host, page);
> > > +
> > > +	/* Skip conf write if we are already in the correct mode */
> > > +	if (codeword_fixup == host->codeword_fixup)
> > > +		return;
> > > +
> > > +	host->codeword_fixup = codeword_fixup;
> > > +
> > > +	host->cw_data = codeword_fixup ? 512 : 516;
> > > +	host->spare_bytes = host->cw_size - host->ecc_bytes_hw -
> > > +			    host->bbm_size - host->cw_data;
> > > +
> > > +	host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK);
> > > +	host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES |
> > > +		      host->cw_data << UD_SIZE_BYTES;
> > > +
> > > +	host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK;
> > > +	host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES;
> > > +	host->ecc_buf_cfg = (codeword_fixup ? 0x1ff : 0x203) << NUM_STEPS;
> > 
> > s/1ff/(512 - 1)
> > s/203/(516 - 1)
> > 
> 
> ok. I wonder if this can just be reduced to (host->cw_data - 1) and
> skipping the check entirely.
> 

Yeah, that sounds even good.

Thanks,
Mani
diff mbox series

Patch

diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index 1a77542c6d67..06ee9a836a3b 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -80,8 +80,10 @@ 
 #define	DISABLE_STATUS_AFTER_WRITE	4
 #define	CW_PER_PAGE			6
 #define	UD_SIZE_BYTES			9
+#define	UD_SIZE_BYTES_MASK		GENMASK(18, 9)
 #define	ECC_PARITY_SIZE_BYTES_RS	19
 #define	SPARE_SIZE_BYTES		23
+#define	SPARE_SIZE_BYTES_MASK		GENMASK(26, 23)
 #define	NUM_ADDR_CYCLES			27
 #define	STATUS_BFR_READ			30
 #define	SET_RD_MODE_AFTER_STATUS	31
@@ -102,6 +104,7 @@ 
 #define	ECC_MODE			4
 #define	ECC_PARITY_SIZE_BYTES_BCH	8
 #define	ECC_NUM_DATA_BYTES		16
+#define	ECC_NUM_DATA_BYTES_MASK		GENMASK(25, 16)
 #define	ECC_FORCE_CLK_OPEN		30
 
 /* NAND_DEV_CMD1 bits */
@@ -418,6 +421,19 @@  struct qcom_nand_controller {
 	const struct qcom_nandc_props *props;
 };
 
+/*
+ * NAND special boot partitions
+ *
+ * @page_offset:		offset of the partition where spare data is not protected
+ *				by ECC (value in pages)
+ * @page_offset:		size of the partition where spare data is not protected
+ *				by ECC (value in pages)
+ */
+struct qcom_nand_boot_partition {
+	u32 page_offset;
+	u32 page_size;
+};
+
 /*
  * NAND chip structure
  *
@@ -444,6 +460,13 @@  struct qcom_nand_controller {
  * @cfg0, cfg1, cfg0_raw..:	NANDc register configurations needed for
  *				ecc/non-ecc mode for the current nand flash
  *				device
+ *
+ * @codeword_fixup:		keep track of the current layout used by
+ *				the driver for read/write operation.
+ * @nr_boot_partitions:		count of the boot partitions where spare data is not
+ *				protected by ECC
+ * @boot_pages:			array of boot partitions where offset and size of the
+ *				boot partitions are stored
  */
 struct qcom_nand_host {
 	struct nand_chip chip;
@@ -466,6 +489,10 @@  struct qcom_nand_host {
 	u32 ecc_bch_cfg;
 	u32 clrflashstatus;
 	u32 clrreadstatus;
+
+	bool codeword_fixup;
+	int nr_boot_partitions;
+	struct qcom_nand_boot_partition *boot_partitions;
 };
 
 /*
@@ -475,6 +502,7 @@  struct qcom_nand_host {
  * @is_bam - whether NAND controller is using BAM
  * @is_qpic - whether NAND CTRL is part of qpic IP
  * @qpic_v2 - flag to indicate QPIC IP version 2
+ * @use_codeword_fixup - whether NAND has different layout for boot partitions
  * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset
  */
 struct qcom_nandc_props {
@@ -482,6 +510,7 @@  struct qcom_nandc_props {
 	bool is_bam;
 	bool is_qpic;
 	bool qpic_v2;
+	bool use_codeword_fixup;
 	u32 dev_cmd_reg_start;
 };
 
@@ -1701,7 +1730,7 @@  qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip,
 	data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
 	oob_size1 = host->bbm_size;
 
-	if (qcom_nandc_is_last_cw(ecc, cw)) {
+	if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) {
 		data_size2 = ecc->size - data_size1 -
 			     ((ecc->steps - 1) * 4);
 		oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw +
@@ -1782,7 +1811,7 @@  check_for_erased_page(struct qcom_nand_host *host, u8 *data_buf,
 	}
 
 	for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) {
-		if (qcom_nandc_is_last_cw(ecc, cw)) {
+		if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) {
 			data_size = ecc->size - ((ecc->steps - 1) * 4);
 			oob_size = (ecc->steps * 4) + host->ecc_bytes_hw;
 		} else {
@@ -1940,7 +1969,7 @@  static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,
 	for (i = 0; i < ecc->steps; i++) {
 		int data_size, oob_size;
 
-		if (qcom_nandc_is_last_cw(ecc, i)) {
+		if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) {
 			data_size = ecc->size - ((ecc->steps - 1) << 2);
 			oob_size = (ecc->steps << 2) + host->ecc_bytes_hw +
 				   host->spare_bytes;
@@ -2037,6 +2066,55 @@  static int copy_last_cw(struct qcom_nand_host *host, int page)
 	return ret;
 }
 
+static bool
+qcom_nandc_is_boot_page(struct qcom_nand_host *host, int page)
+{
+	struct qcom_nand_boot_partition *boot_partition;
+	u32 start, end;
+	int i;
+
+	for (i = 0; i < host->nr_boot_partitions; i++) {
+		boot_partition = &host->boot_partitions[i];
+		start = boot_partition->page_offset;
+		end = start + boot_partition->page_size;
+
+		/* Boot pages are normally at the start of
+		 * the nand in various partition.
+		 * Check the page from the boot page end first
+		 * to save one extra check and optimize this
+		 * in case real no-boot partition are used.
+		 */
+		if (page < end && page >= start)
+			return true;
+	}
+
+	return false;
+}
+
+static void
+qcom_nandc_codeword_fixup(struct qcom_nand_host *host, int page)
+{
+	bool codeword_fixup = qcom_nandc_is_boot_page(host, page);
+
+	/* Skip conf write if we are already in the correct mode */
+	if (codeword_fixup == host->codeword_fixup)
+		return;
+
+	host->codeword_fixup = codeword_fixup;
+
+	host->cw_data = codeword_fixup ? 512 : 516;
+	host->spare_bytes = host->cw_size - host->ecc_bytes_hw -
+			    host->bbm_size - host->cw_data;
+
+	host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK);
+	host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES |
+		      host->cw_data << UD_SIZE_BYTES;
+
+	host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK;
+	host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES;
+	host->ecc_buf_cfg = (codeword_fixup ? 0x1ff : 0x203) << NUM_STEPS;
+}
+
 /* implements ecc->read_page() */
 static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf,
 				int oob_required, int page)
@@ -2045,6 +2123,9 @@  static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf,
 	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
 	u8 *data_buf, *oob_buf = NULL;
 
+	if (host->nr_boot_partitions)
+		qcom_nandc_codeword_fixup(host, page);
+
 	nand_read_page_op(chip, page, 0, NULL, 0);
 	data_buf = buf;
 	oob_buf = oob_required ? chip->oob_poi : NULL;
@@ -2064,6 +2145,9 @@  static int qcom_nandc_read_page_raw(struct nand_chip *chip, uint8_t *buf,
 	int cw, ret;
 	u8 *data_buf = buf, *oob_buf = chip->oob_poi;
 
+	if (host->nr_boot_partitions)
+		qcom_nandc_codeword_fixup(host, page);
+
 	for (cw = 0; cw < ecc->steps; cw++) {
 		ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf,
 					     page, cw);
@@ -2084,6 +2168,9 @@  static int qcom_nandc_read_oob(struct nand_chip *chip, int page)
 	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
 	struct nand_ecc_ctrl *ecc = &chip->ecc;
 
+	if (host->nr_boot_partitions)
+		qcom_nandc_codeword_fixup(host, page);
+
 	clear_read_regs(nandc);
 	clear_bam_transaction(nandc);
 
@@ -2104,6 +2191,9 @@  static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf,
 	u8 *data_buf, *oob_buf;
 	int i, ret;
 
+	if (host->nr_boot_partitions)
+		qcom_nandc_codeword_fixup(host, page);
+
 	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
 
 	clear_read_regs(nandc);
@@ -2119,7 +2209,7 @@  static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf,
 	for (i = 0; i < ecc->steps; i++) {
 		int data_size, oob_size;
 
-		if (qcom_nandc_is_last_cw(ecc, i)) {
+		if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) {
 			data_size = ecc->size - ((ecc->steps - 1) << 2);
 			oob_size = (ecc->steps << 2) + host->ecc_bytes_hw +
 				   host->spare_bytes;
@@ -2176,6 +2266,9 @@  static int qcom_nandc_write_page_raw(struct nand_chip *chip,
 	u8 *data_buf, *oob_buf;
 	int i, ret;
 
+	if (host->nr_boot_partitions)
+		qcom_nandc_codeword_fixup(host, page);
+
 	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
 	clear_read_regs(nandc);
 	clear_bam_transaction(nandc);
@@ -2194,7 +2287,7 @@  static int qcom_nandc_write_page_raw(struct nand_chip *chip,
 		data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1);
 		oob_size1 = host->bbm_size;
 
-		if (qcom_nandc_is_last_cw(ecc, i)) {
+		if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) {
 			data_size2 = ecc->size - data_size1 -
 				     ((ecc->steps - 1) << 2);
 			oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw +
@@ -2254,6 +2347,9 @@  static int qcom_nandc_write_oob(struct nand_chip *chip, int page)
 	int data_size, oob_size;
 	int ret;
 
+	if (host->nr_boot_partitions)
+		qcom_nandc_codeword_fixup(host, page);
+
 	host->use_ecc = true;
 	clear_bam_transaction(nandc);
 
@@ -2902,6 +2998,71 @@  static int qcom_nandc_setup(struct qcom_nand_controller *nandc)
 
 static const char * const probes[] = { "cmdlinepart", "ofpart", "qcomsmem", NULL };
 
+static int qcom_nand_host_parse_boot_partitions(struct qcom_nand_controller *nandc,
+						struct qcom_nand_host *host,
+						struct device_node *dn)
+{
+	struct nand_chip *chip = &host->chip;
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	struct qcom_nand_boot_partition *boot_partition;
+	struct device *dev = nandc->dev;
+	int partitions_count, i, j, ret;
+
+	if (!nandc->props->use_codeword_fixup)
+		return 0;
+
+	if (!of_find_property(dn, "qcom,boot-partitions", NULL))
+		return 0;
+
+	partitions_count = of_property_count_u32_elems(dn, "qcom,boot-partitions");
+	if (partitions_count < 0) {
+		dev_err(dev, "Error parsing boot partition.");
+		return ret;
+	}
+
+	host->nr_boot_partitions = partitions_count / 2;
+	host->boot_partitions = devm_kcalloc(dev, host->nr_boot_partitions,
+					     sizeof(*host->boot_partitions), GFP_KERNEL);
+	if (!host->boot_partitions)
+		return -ENOMEM;
+
+	for (i = 0, j = 0; i < host->nr_boot_partitions; i++, j += 2) {
+		boot_partition = &host->boot_partitions[i];
+
+		ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j,
+						 &boot_partition->page_offset);
+		if (ret) {
+			dev_err(dev, "Error parsing boot partition offset at index %d", i);
+			return ret;
+		}
+
+		if (boot_partition->page_offset % mtd->writesize) {
+			dev_err(dev, "Boot partition offset not multiple of writesize at index %i",
+				i);
+			return -EINVAL;
+		}
+		/* Convert offset to nand pages */
+		boot_partition->page_offset /= mtd->writesize;
+
+		ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j + 1,
+						 &boot_partition->page_size);
+		if (ret) {
+			dev_err(dev, "Error parsing boot partition size at index %d", i);
+			return ret;
+		}
+
+		if (boot_partition->page_size % mtd->writesize) {
+			dev_err(dev, "Boot partition size not multiple of writesize at index %i",
+				i);
+			return -EINVAL;
+		}
+		/* Convert size to nand pages */
+		boot_partition->page_size /= mtd->writesize;
+	}
+
+	return 0;
+}
+
 static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc,
 					    struct qcom_nand_host *host,
 					    struct device_node *dn)
@@ -2970,6 +3131,8 @@  static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc,
 	if (ret)
 		nand_cleanup(chip);
 
+	qcom_nand_host_parse_boot_partitions(nandc, host, dn);
+
 	return ret;
 }
 
@@ -3135,6 +3298,7 @@  static int qcom_nandc_remove(struct platform_device *pdev)
 static const struct qcom_nandc_props ipq806x_nandc_props = {
 	.ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT),
 	.is_bam = false,
+	.use_codeword_fixup = true,
 	.dev_cmd_reg_start = 0x0,
 };