| Message ID | 20220608001030.18813-2-ansuelsmth@gmail.com |
|---|---|
| State | New |
| Headers | show |
| Series | [v5,1/3] mtd: nand: raw: qcom_nandc: add support for unprotected spare data pages | expand |
On Wed, Jun 08, 2022 at 02:10:28AM +0200, Ansuel Smith wrote: > IPQ8064 nand have special pages where a different layout scheme is used. > These special page are used by boot partition and on reading them > lots of warning are reported about wrong ECC data and if written to > results in broken data and not bootable device. > > The layout scheme used by these special page consist in using 512 bytes > as the codeword size (even for the last codeword) while writing to CFG0 > register. This forces the NAND controller to unprotect the 4 bytes of > spare data. > > Since the kernel is unaware of this different layout for these special > page, it does try to protect the spare data too during read/write and > warn about CRC errors. > > Add support for this by permitting the user to declare these special > pages in dts by declaring offset and size of the partition. The driver > internally will convert these value to nand pages. > > On user read/write the page is checked and if it's a boot page the > correct layout is used. > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > --- > drivers/mtd/nand/raw/qcom_nandc.c | 174 +++++++++++++++++++++++++++++- > 1 file changed, 169 insertions(+), 5 deletions(-) > > diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c > index 1a77542c6d67..06ee9a836a3b 100644 > --- a/drivers/mtd/nand/raw/qcom_nandc.c > +++ b/drivers/mtd/nand/raw/qcom_nandc.c > @@ -80,8 +80,10 @@ > #define DISABLE_STATUS_AFTER_WRITE 4 > #define CW_PER_PAGE 6 > #define UD_SIZE_BYTES 9 > +#define UD_SIZE_BYTES_MASK GENMASK(18, 9) > #define ECC_PARITY_SIZE_BYTES_RS 19 > #define SPARE_SIZE_BYTES 23 > +#define SPARE_SIZE_BYTES_MASK GENMASK(26, 23) > #define NUM_ADDR_CYCLES 27 > #define STATUS_BFR_READ 30 > #define SET_RD_MODE_AFTER_STATUS 31 > @@ -102,6 +104,7 @@ > #define ECC_MODE 4 > #define ECC_PARITY_SIZE_BYTES_BCH 8 > #define ECC_NUM_DATA_BYTES 16 > +#define ECC_NUM_DATA_BYTES_MASK GENMASK(25, 16) > #define ECC_FORCE_CLK_OPEN 30 > > /* NAND_DEV_CMD1 bits */ > @@ -418,6 +421,19 @@ struct qcom_nand_controller { > const struct qcom_nandc_props *props; > }; > > +/* > + * NAND special boot partitions > + * > + * @page_offset: offset of the partition where spare data is not protected > + * by ECC (value in pages) s/page_offset/offset > + * @page_offset: size of the partition where spare data is not protected > + * by ECC (value in pages) s/page_offset/size > + */ > +struct qcom_nand_boot_partition { > + u32 page_offset; > + u32 page_size; same here > +}; > + > /* > * NAND chip structure > * > @@ -444,6 +460,13 @@ struct qcom_nand_controller { > * @cfg0, cfg1, cfg0_raw..: NANDc register configurations needed for > * ecc/non-ecc mode for the current nand flash > * device > + * > + * @codeword_fixup: keep track of the current layout used by > + * the driver for read/write operation. > + * @nr_boot_partitions: count of the boot partitions where spare data is not > + * protected by ECC Align the Kdoc comments w.r.t other members. > + * @boot_pages: array of boot partitions where offset and size of the > + * boot partitions are stored s/boot_pages/boot_partitions > */ > struct qcom_nand_host { > struct nand_chip chip; > @@ -466,6 +489,10 @@ struct qcom_nand_host { > u32 ecc_bch_cfg; > u32 clrflashstatus; > u32 clrreadstatus; > + > + bool codeword_fixup; > + int nr_boot_partitions; > + struct qcom_nand_boot_partition *boot_partitions; > }; > > /* > @@ -475,6 +502,7 @@ struct qcom_nand_host { > * @is_bam - whether NAND controller is using BAM > * @is_qpic - whether NAND CTRL is part of qpic IP > * @qpic_v2 - flag to indicate QPIC IP version 2 > + * @use_codeword_fixup - whether NAND has different layout for boot partitions > * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset > */ > struct qcom_nandc_props { > @@ -482,6 +510,7 @@ struct qcom_nandc_props { > bool is_bam; > bool is_qpic; > bool qpic_v2; > + bool use_codeword_fixup; > u32 dev_cmd_reg_start; > }; > > @@ -1701,7 +1730,7 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, > data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); > oob_size1 = host->bbm_size; > > - if (qcom_nandc_is_last_cw(ecc, cw)) { > + if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) { > data_size2 = ecc->size - data_size1 - > ((ecc->steps - 1) * 4); > oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw + > @@ -1782,7 +1811,7 @@ check_for_erased_page(struct qcom_nand_host *host, u8 *data_buf, > } > > for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) { > - if (qcom_nandc_is_last_cw(ecc, cw)) { > + if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) { > data_size = ecc->size - ((ecc->steps - 1) * 4); > oob_size = (ecc->steps * 4) + host->ecc_bytes_hw; > } else { > @@ -1940,7 +1969,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, > for (i = 0; i < ecc->steps; i++) { > int data_size, oob_size; > > - if (qcom_nandc_is_last_cw(ecc, i)) { > + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { > data_size = ecc->size - ((ecc->steps - 1) << 2); > oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + > host->spare_bytes; > @@ -2037,6 +2066,55 @@ static int copy_last_cw(struct qcom_nand_host *host, int page) > return ret; > } > > +static bool > +qcom_nandc_is_boot_page(struct qcom_nand_host *host, int page) Move function name to previous line. If it exceeds 100 lines then wrap arguments. s/qcom_nandc_is_boot_page/qcom_nandc_is_boot_partition > +{ > + struct qcom_nand_boot_partition *boot_partition; > + u32 start, end; > + int i; > + > + for (i = 0; i < host->nr_boot_partitions; i++) { > + boot_partition = &host->boot_partitions[i]; > + start = boot_partition->page_offset; > + end = start + boot_partition->page_size; > + > + /* Boot pages are normally at the start of Block comments should start with: /* * ... Also, are you sure that only few pages in the partitions have different layout and not all pages? If not, then this comment needs to be reworded. > + * the nand in various partition. > + * Check the page from the boot page end first > + * to save one extra check and optimize this > + * in case real no-boot partition are used. > + */ > + if (page < end && page >= start) > + return true; > + } > + > + return false; > +} > + > +static void > +qcom_nandc_codeword_fixup(struct qcom_nand_host *host, int page) > +{ > + bool codeword_fixup = qcom_nandc_is_boot_page(host, page); > + > + /* Skip conf write if we are already in the correct mode */ > + if (codeword_fixup == host->codeword_fixup) > + return; > + > + host->codeword_fixup = codeword_fixup; > + > + host->cw_data = codeword_fixup ? 512 : 516; > + host->spare_bytes = host->cw_size - host->ecc_bytes_hw - > + host->bbm_size - host->cw_data; > + > + host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK); > + host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES | > + host->cw_data << UD_SIZE_BYTES; > + > + host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK; > + host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES; > + host->ecc_buf_cfg = (codeword_fixup ? 0x1ff : 0x203) << NUM_STEPS; s/1ff/(512 - 1) s/203/(516 - 1) > +} > + > /* implements ecc->read_page() */ > static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, > int oob_required, int page) > @@ -2045,6 +2123,9 @@ static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, > struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); > u8 *data_buf, *oob_buf = NULL; > > + if (host->nr_boot_partitions) > + qcom_nandc_codeword_fixup(host, page); > + > nand_read_page_op(chip, page, 0, NULL, 0); > data_buf = buf; > oob_buf = oob_required ? chip->oob_poi : NULL; > @@ -2064,6 +2145,9 @@ static int qcom_nandc_read_page_raw(struct nand_chip *chip, uint8_t *buf, > int cw, ret; > u8 *data_buf = buf, *oob_buf = chip->oob_poi; > > + if (host->nr_boot_partitions) > + qcom_nandc_codeword_fixup(host, page); > + > for (cw = 0; cw < ecc->steps; cw++) { > ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf, > page, cw); > @@ -2084,6 +2168,9 @@ static int qcom_nandc_read_oob(struct nand_chip *chip, int page) > struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); > struct nand_ecc_ctrl *ecc = &chip->ecc; > > + if (host->nr_boot_partitions) > + qcom_nandc_codeword_fixup(host, page); > + > clear_read_regs(nandc); > clear_bam_transaction(nandc); > > @@ -2104,6 +2191,9 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf, > u8 *data_buf, *oob_buf; > int i, ret; > > + if (host->nr_boot_partitions) > + qcom_nandc_codeword_fixup(host, page); > + > nand_prog_page_begin_op(chip, page, 0, NULL, 0); > > clear_read_regs(nandc); > @@ -2119,7 +2209,7 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf, > for (i = 0; i < ecc->steps; i++) { > int data_size, oob_size; > > - if (qcom_nandc_is_last_cw(ecc, i)) { > + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { > data_size = ecc->size - ((ecc->steps - 1) << 2); > oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + > host->spare_bytes; > @@ -2176,6 +2266,9 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip, > u8 *data_buf, *oob_buf; > int i, ret; > > + if (host->nr_boot_partitions) > + qcom_nandc_codeword_fixup(host, page); > + > nand_prog_page_begin_op(chip, page, 0, NULL, 0); > clear_read_regs(nandc); > clear_bam_transaction(nandc); > @@ -2194,7 +2287,7 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip, > data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); > oob_size1 = host->bbm_size; > > - if (qcom_nandc_is_last_cw(ecc, i)) { > + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { > data_size2 = ecc->size - data_size1 - > ((ecc->steps - 1) << 2); > oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + > @@ -2254,6 +2347,9 @@ static int qcom_nandc_write_oob(struct nand_chip *chip, int page) > int data_size, oob_size; > int ret; > > + if (host->nr_boot_partitions) > + qcom_nandc_codeword_fixup(host, page); > + > host->use_ecc = true; > clear_bam_transaction(nandc); > > @@ -2902,6 +2998,71 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) > > static const char * const probes[] = { "cmdlinepart", "ofpart", "qcomsmem", NULL }; > > +static int qcom_nand_host_parse_boot_partitions(struct qcom_nand_controller *nandc, > + struct qcom_nand_host *host, > + struct device_node *dn) > +{ > + struct nand_chip *chip = &host->chip; > + struct mtd_info *mtd = nand_to_mtd(chip); > + struct qcom_nand_boot_partition *boot_partition; > + struct device *dev = nandc->dev; > + int partitions_count, i, j, ret; > + > + if (!nandc->props->use_codeword_fixup) > + return 0; Move this check to caller as I suggested previously. > + > + if (!of_find_property(dn, "qcom,boot-partitions", NULL)) > + return 0; > + > + partitions_count = of_property_count_u32_elems(dn, "qcom,boot-partitions"); > + if (partitions_count < 0) { partitions_count <= 0 > + dev_err(dev, "Error parsing boot partition."); Add newline at the end of error message > + return ret; > + } > + > + host->nr_boot_partitions = partitions_count / 2; > + host->boot_partitions = devm_kcalloc(dev, host->nr_boot_partitions, > + sizeof(*host->boot_partitions), GFP_KERNEL); > + if (!host->boot_partitions) host->nr_boot_partitions = 0; > + return -ENOMEM; > + > + for (i = 0, j = 0; i < host->nr_boot_partitions; i++, j += 2) { > + boot_partition = &host->boot_partitions[i]; > + > + ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j, > + &boot_partition->page_offset); > + if (ret) { > + dev_err(dev, "Error parsing boot partition offset at index %d", i); Add newline at the end of error message. Do the same for all error prints. > + return ret; > + } > + > + if (boot_partition->page_offset % mtd->writesize) { > + dev_err(dev, "Boot partition offset not multiple of writesize at index %i", > + i); > + return -EINVAL; > + } > + /* Convert offset to nand pages */ s/pages/partitions > + boot_partition->page_offset /= mtd->writesize; s/page_offset/offset > + > + ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j + 1, > + &boot_partition->page_size); > + if (ret) { > + dev_err(dev, "Error parsing boot partition size at index %d", i); > + return ret; > + } > + > + if (boot_partition->page_size % mtd->writesize) { s/page_size/size here and below > + dev_err(dev, "Boot partition size not multiple of writesize at index %i", > + i); > + return -EINVAL; > + } > + /* Convert size to nand pages */ s/pages/partitions Thanks, Mani > + boot_partition->page_size /= mtd->writesize; > + } > + > + return 0; > +} > + > static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, > struct qcom_nand_host *host, > struct device_node *dn) > @@ -2970,6 +3131,8 @@ static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, > if (ret) > nand_cleanup(chip); > > + qcom_nand_host_parse_boot_partitions(nandc, host, dn); > + > return ret; > } > > @@ -3135,6 +3298,7 @@ static int qcom_nandc_remove(struct platform_device *pdev) > static const struct qcom_nandc_props ipq806x_nandc_props = { > .ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT), > .is_bam = false, > + .use_codeword_fixup = true, > .dev_cmd_reg_start = 0x0, > }; > > -- > 2.36.1 >
On Thu, Jun 09, 2022 at 01:22:54PM +0530, Manivannan Sadhasivam wrote: > On Wed, Jun 08, 2022 at 02:10:28AM +0200, Ansuel Smith wrote: > > IPQ8064 nand have special pages where a different layout scheme is used. > > These special page are used by boot partition and on reading them > > lots of warning are reported about wrong ECC data and if written to > > results in broken data and not bootable device. > > > > The layout scheme used by these special page consist in using 512 bytes > > as the codeword size (even for the last codeword) while writing to CFG0 > > register. This forces the NAND controller to unprotect the 4 bytes of > > spare data. > > > > Since the kernel is unaware of this different layout for these special > > page, it does try to protect the spare data too during read/write and > > warn about CRC errors. > > > > Add support for this by permitting the user to declare these special > > pages in dts by declaring offset and size of the partition. The driver > > internally will convert these value to nand pages. > > > > On user read/write the page is checked and if it's a boot page the > > correct layout is used. > > > > Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> > > --- > > drivers/mtd/nand/raw/qcom_nandc.c | 174 +++++++++++++++++++++++++++++- > > 1 file changed, 169 insertions(+), 5 deletions(-) > > > > diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c > > index 1a77542c6d67..06ee9a836a3b 100644 > > --- a/drivers/mtd/nand/raw/qcom_nandc.c > > +++ b/drivers/mtd/nand/raw/qcom_nandc.c > > @@ -80,8 +80,10 @@ > > #define DISABLE_STATUS_AFTER_WRITE 4 > > #define CW_PER_PAGE 6 > > #define UD_SIZE_BYTES 9 > > +#define UD_SIZE_BYTES_MASK GENMASK(18, 9) > > #define ECC_PARITY_SIZE_BYTES_RS 19 > > #define SPARE_SIZE_BYTES 23 > > +#define SPARE_SIZE_BYTES_MASK GENMASK(26, 23) > > #define NUM_ADDR_CYCLES 27 > > #define STATUS_BFR_READ 30 > > #define SET_RD_MODE_AFTER_STATUS 31 > > @@ -102,6 +104,7 @@ > > #define ECC_MODE 4 > > #define ECC_PARITY_SIZE_BYTES_BCH 8 > > #define ECC_NUM_DATA_BYTES 16 > > +#define ECC_NUM_DATA_BYTES_MASK GENMASK(25, 16) > > #define ECC_FORCE_CLK_OPEN 30 > > > > /* NAND_DEV_CMD1 bits */ > > @@ -418,6 +421,19 @@ struct qcom_nand_controller { > > const struct qcom_nandc_props *props; > > }; > > > > +/* > > + * NAND special boot partitions > > + * > > + * @page_offset: offset of the partition where spare data is not protected > > + * by ECC (value in pages) > > s/page_offset/offset > Mhhh i changed this to page_offset since the struct is called boot_partition and it can be confusing since internally the values is in pages. Someone can think that the real partition offset/size is used instead of the value converted in pages. > > + * @page_offset: size of the partition where spare data is not protected > > + * by ECC (value in pages) > > s/page_offset/size > > > + */ > > +struct qcom_nand_boot_partition { > > + u32 page_offset; > > + u32 page_size; > > same here > > > +}; > > + > > /* > > * NAND chip structure > > * > > @@ -444,6 +460,13 @@ struct qcom_nand_controller { > > * @cfg0, cfg1, cfg0_raw..: NANDc register configurations needed for > > * ecc/non-ecc mode for the current nand flash > > * device > > + * > > + * @codeword_fixup: keep track of the current layout used by > > + * the driver for read/write operation. > > + * @nr_boot_partitions: count of the boot partitions where spare data is not > > + * protected by ECC > > Align the Kdoc comments w.r.t other members. > > > + * @boot_pages: array of boot partitions where offset and size of the > > + * boot partitions are stored > > s/boot_pages/boot_partitions > Sorry. > > */ > > struct qcom_nand_host { > > struct nand_chip chip; > > @@ -466,6 +489,10 @@ struct qcom_nand_host { > > u32 ecc_bch_cfg; > > u32 clrflashstatus; > > u32 clrreadstatus; > > + > > + bool codeword_fixup; > > + int nr_boot_partitions; > > + struct qcom_nand_boot_partition *boot_partitions; > > }; > > > > /* > > @@ -475,6 +502,7 @@ struct qcom_nand_host { > > * @is_bam - whether NAND controller is using BAM > > * @is_qpic - whether NAND CTRL is part of qpic IP > > * @qpic_v2 - flag to indicate QPIC IP version 2 > > + * @use_codeword_fixup - whether NAND has different layout for boot partitions > > * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset > > */ > > struct qcom_nandc_props { > > @@ -482,6 +510,7 @@ struct qcom_nandc_props { > > bool is_bam; > > bool is_qpic; > > bool qpic_v2; > > + bool use_codeword_fixup; > > u32 dev_cmd_reg_start; > > }; > > > > @@ -1701,7 +1730,7 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, > > data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); > > oob_size1 = host->bbm_size; > > > > - if (qcom_nandc_is_last_cw(ecc, cw)) { > > + if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) { > > data_size2 = ecc->size - data_size1 - > > ((ecc->steps - 1) * 4); > > oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw + > > @@ -1782,7 +1811,7 @@ check_for_erased_page(struct qcom_nand_host *host, u8 *data_buf, > > } > > > > for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) { > > - if (qcom_nandc_is_last_cw(ecc, cw)) { > > + if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) { > > data_size = ecc->size - ((ecc->steps - 1) * 4); > > oob_size = (ecc->steps * 4) + host->ecc_bytes_hw; > > } else { > > @@ -1940,7 +1969,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, > > for (i = 0; i < ecc->steps; i++) { > > int data_size, oob_size; > > > > - if (qcom_nandc_is_last_cw(ecc, i)) { > > + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { > > data_size = ecc->size - ((ecc->steps - 1) << 2); > > oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + > > host->spare_bytes; > > @@ -2037,6 +2066,55 @@ static int copy_last_cw(struct qcom_nand_host *host, int page) > > return ret; > > } > > > > +static bool > > +qcom_nandc_is_boot_page(struct qcom_nand_host *host, int page) > > Move function name to previous line. If it exceeds 100 lines then wrap > arguments. > > s/qcom_nandc_is_boot_page/qcom_nandc_is_boot_partition > Again considering the check is done on the page and not on the partition, wonder what is correct. > > +{ > > + struct qcom_nand_boot_partition *boot_partition; > > + u32 start, end; > > + int i; > > + > > + for (i = 0; i < host->nr_boot_partitions; i++) { > > + boot_partition = &host->boot_partitions[i]; > > + start = boot_partition->page_offset; > > + end = start + boot_partition->page_size; > > + > > + /* Boot pages are normally at the start of > > Block comments should start with: > > /* > * ... > > Also, are you sure that only few pages in the partitions have different layout > and not all pages? If not, then this comment needs to be reworded. > I probably worderd this bad... Each page of the boot partitions require the codeword fix. But other may have the normal codeword For example this is from a Netgear router: mtd0: 00c80000 00020000 "qcadata" (require codeword fix) mtd1: 00500000 00020000 "APPSBL" (require codeword fix) mtd2: 00080000 00020000 "APPSBLENV" (doesn't require codeword fix) mtd3: 00140000 00020000 "art" (doesn't) mtd4: 00140000 00020000 "artbak" (doesn't) mtd5: 00400000 00020000 "kernel" (doesn't) mtd6: 06080000 00020000 "ubi" (doesn't) mtd7: 00700000 00020000 "reserve" (doesn't) This is part of the case tho as there are some partition table with something like mtd0: 00c80000 00020000 "qcadata" (require codeword fix) mtd1: 00500000 00020000 "APPSBL" (require codeword fix) mtd2: 00080000 00020000 "APPSBLENV" (doesn't require codeword fix) mtd3: 00140000 00020000 "APPSBL2" (require codeword fix) [...] In all case 99% of the time in a normal system what you commonly write are the rootfs partition that are AFTER the boot partition so checking if the page is after such partition should speed up the check. Now that I think about it, a good idea is also start checking the boot_partition table from the end to improve the checking even more. So tell me if the comments is wronlgy worded. > > + * the nand in various partition. > > + * Check the page from the boot page end first > > + * to save one extra check and optimize this > > + * in case real no-boot partition are used. > > + */ > > + if (page < end && page >= start) > > + return true; > > + } > > + > > + return false; > > +} > > + > > +static void > > +qcom_nandc_codeword_fixup(struct qcom_nand_host *host, int page) > > +{ > > + bool codeword_fixup = qcom_nandc_is_boot_page(host, page); > > + > > + /* Skip conf write if we are already in the correct mode */ > > + if (codeword_fixup == host->codeword_fixup) > > + return; > > + > > + host->codeword_fixup = codeword_fixup; > > + > > + host->cw_data = codeword_fixup ? 512 : 516; > > + host->spare_bytes = host->cw_size - host->ecc_bytes_hw - > > + host->bbm_size - host->cw_data; > > + > > + host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK); > > + host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES | > > + host->cw_data << UD_SIZE_BYTES; > > + > > + host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK; > > + host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES; > > + host->ecc_buf_cfg = (codeword_fixup ? 0x1ff : 0x203) << NUM_STEPS; > > s/1ff/(512 - 1) > s/203/(516 - 1) > ok. I wonder if this can just be reduced to (host->cw_data - 1) and skipping the check entirely. > > +} > > + > > /* implements ecc->read_page() */ > > static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, > > int oob_required, int page) > > @@ -2045,6 +2123,9 @@ static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, > > struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); > > u8 *data_buf, *oob_buf = NULL; > > > > + if (host->nr_boot_partitions) > > + qcom_nandc_codeword_fixup(host, page); > > + > > nand_read_page_op(chip, page, 0, NULL, 0); > > data_buf = buf; > > oob_buf = oob_required ? chip->oob_poi : NULL; > > @@ -2064,6 +2145,9 @@ static int qcom_nandc_read_page_raw(struct nand_chip *chip, uint8_t *buf, > > int cw, ret; > > u8 *data_buf = buf, *oob_buf = chip->oob_poi; > > > > + if (host->nr_boot_partitions) > > + qcom_nandc_codeword_fixup(host, page); > > + > > for (cw = 0; cw < ecc->steps; cw++) { > > ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf, > > page, cw); > > @@ -2084,6 +2168,9 @@ static int qcom_nandc_read_oob(struct nand_chip *chip, int page) > > struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); > > struct nand_ecc_ctrl *ecc = &chip->ecc; > > > > + if (host->nr_boot_partitions) > > + qcom_nandc_codeword_fixup(host, page); > > + > > clear_read_regs(nandc); > > clear_bam_transaction(nandc); > > > > @@ -2104,6 +2191,9 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf, > > u8 *data_buf, *oob_buf; > > int i, ret; > > > > + if (host->nr_boot_partitions) > > + qcom_nandc_codeword_fixup(host, page); > > + > > nand_prog_page_begin_op(chip, page, 0, NULL, 0); > > > > clear_read_regs(nandc); > > @@ -2119,7 +2209,7 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf, > > for (i = 0; i < ecc->steps; i++) { > > int data_size, oob_size; > > > > - if (qcom_nandc_is_last_cw(ecc, i)) { > > + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { > > data_size = ecc->size - ((ecc->steps - 1) << 2); > > oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + > > host->spare_bytes; > > @@ -2176,6 +2266,9 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip, > > u8 *data_buf, *oob_buf; > > int i, ret; > > > > + if (host->nr_boot_partitions) > > + qcom_nandc_codeword_fixup(host, page); > > + > > nand_prog_page_begin_op(chip, page, 0, NULL, 0); > > clear_read_regs(nandc); > > clear_bam_transaction(nandc); > > @@ -2194,7 +2287,7 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip, > > data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); > > oob_size1 = host->bbm_size; > > > > - if (qcom_nandc_is_last_cw(ecc, i)) { > > + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { > > data_size2 = ecc->size - data_size1 - > > ((ecc->steps - 1) << 2); > > oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + > > @@ -2254,6 +2347,9 @@ static int qcom_nandc_write_oob(struct nand_chip *chip, int page) > > int data_size, oob_size; > > int ret; > > > > + if (host->nr_boot_partitions) > > + qcom_nandc_codeword_fixup(host, page); > > + > > host->use_ecc = true; > > clear_bam_transaction(nandc); > > > > @@ -2902,6 +2998,71 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) > > > > static const char * const probes[] = { "cmdlinepart", "ofpart", "qcomsmem", NULL }; > > > > +static int qcom_nand_host_parse_boot_partitions(struct qcom_nand_controller *nandc, > > + struct qcom_nand_host *host, > > + struct device_node *dn) > > +{ > > + struct nand_chip *chip = &host->chip; > > + struct mtd_info *mtd = nand_to_mtd(chip); > > + struct qcom_nand_boot_partition *boot_partition; > > + struct device *dev = nandc->dev; > > + int partitions_count, i, j, ret; > > + > > + if (!nandc->props->use_codeword_fixup) > > + return 0; > > Move this check to caller as I suggested previously. > Sorry I missed that. > > + > > + if (!of_find_property(dn, "qcom,boot-partitions", NULL)) > > + return 0; > > + > > + partitions_count = of_property_count_u32_elems(dn, "qcom,boot-partitions"); > > + if (partitions_count < 0) { > > partitions_count <= 0 > > > + dev_err(dev, "Error parsing boot partition."); > > Add newline at the end of error message > > > + return ret; > > + } > > + > > + host->nr_boot_partitions = partitions_count / 2; > > + host->boot_partitions = devm_kcalloc(dev, host->nr_boot_partitions, > > + sizeof(*host->boot_partitions), GFP_KERNEL); > > + if (!host->boot_partitions) > > host->nr_boot_partitions = 0; > > > + return -ENOMEM; > > + > > + for (i = 0, j = 0; i < host->nr_boot_partitions; i++, j += 2) { > > + boot_partition = &host->boot_partitions[i]; > > + > > + ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j, > > + &boot_partition->page_offset); > > + if (ret) { > > + dev_err(dev, "Error parsing boot partition offset at index %d", i); > > Add newline at the end of error message. Do the same for all error prints. > > > + return ret; > > + } > > + > > + if (boot_partition->page_offset % mtd->writesize) { > > + dev_err(dev, "Boot partition offset not multiple of writesize at index %i", > > + i); > > + return -EINVAL; > > + } > > + /* Convert offset to nand pages */ > > s/pages/partitions > > > + boot_partition->page_offset /= mtd->writesize; > > s/page_offset/offset > > > + > > + ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j + 1, > > + &boot_partition->page_size); > > + if (ret) { > > + dev_err(dev, "Error parsing boot partition size at index %d", i); > > + return ret; > > + } > > + > > + if (boot_partition->page_size % mtd->writesize) { > > s/page_size/size here and below > > > + dev_err(dev, "Boot partition size not multiple of writesize at index %i", > > + i); > > + return -EINVAL; > > + } > > + /* Convert size to nand pages */ > > s/pages/partitions > > Thanks, > Mani > > > + boot_partition->page_size /= mtd->writesize; > > + } > > + > > + return 0; > > +} > > + > > static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, > > struct qcom_nand_host *host, > > struct device_node *dn) > > @@ -2970,6 +3131,8 @@ static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, > > if (ret) > > nand_cleanup(chip); > > > > + qcom_nand_host_parse_boot_partitions(nandc, host, dn); > > + > > return ret; > > } > > > > @@ -3135,6 +3298,7 @@ static int qcom_nandc_remove(struct platform_device *pdev) > > static const struct qcom_nandc_props ipq806x_nandc_props = { > > .ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT), > > .is_bam = false, > > + .use_codeword_fixup = true, > > .dev_cmd_reg_start = 0x0, > > }; > > > > -- > > 2.36.1 > > > > -- > மணிவண்ணன் சதாசிவம்
Hi Ansuel,
Thank you for the patch! Perhaps something to improve:
[auto build test WARNING on mtd/nand/next]
[also build test WARNING on mtd/mtd/next mtd/mtd/fixes robh/for-next v5.19-rc2 next-20220610]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/intel-lab-lkp/linux/commits/Ansuel-Smith/Add-support-for-unprotected-spare-data-page/20220608-104834
base: https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next
config: hexagon-randconfig-r041-20220613 (https://download.01.org/0day-ci/archive/20220613/202206132205.G3tGFPx7-lkp@intel.com/config)
compiler: clang version 15.0.0 (https://github.com/llvm/llvm-project d378268ead93c85803c270277f0243737b536ae7)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/intel-lab-lkp/linux/commit/5f9263b88e99a6cae44be5e737cb0928ee420e87
git remote add linux-review https://github.com/intel-lab-lkp/linux
git fetch --no-tags linux-review Ansuel-Smith/Add-support-for-unprotected-spare-data-page/20220608-104834
git checkout 5f9263b88e99a6cae44be5e737cb0928ee420e87
# save the config file
mkdir build_dir && cp config build_dir/.config
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=hexagon SHELL=/bin/bash drivers/mtd/nand/raw/
If you fix the issue, kindly add following tag where applicable
Reported-by: kernel test robot <lkp@intel.com>
All warnings (new ones prefixed by >>):
>> drivers/mtd/nand/raw/qcom_nandc.c:3020:10: warning: variable 'ret' is uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mtd/nand/raw/qcom_nandc.c:3009:33: note: initialize the variable 'ret' to silence this warning
int partitions_count, i, j, ret;
^
= 0
1 warning generated.
vim +/ret +3020 drivers/mtd/nand/raw/qcom_nandc.c
3000
3001 static int qcom_nand_host_parse_boot_partitions(struct qcom_nand_controller *nandc,
3002 struct qcom_nand_host *host,
3003 struct device_node *dn)
3004 {
3005 struct nand_chip *chip = &host->chip;
3006 struct mtd_info *mtd = nand_to_mtd(chip);
3007 struct qcom_nand_boot_partition *boot_partition;
3008 struct device *dev = nandc->dev;
3009 int partitions_count, i, j, ret;
3010
3011 if (!nandc->props->use_codeword_fixup)
3012 return 0;
3013
3014 if (!of_find_property(dn, "qcom,boot-partitions", NULL))
3015 return 0;
3016
3017 partitions_count = of_property_count_u32_elems(dn, "qcom,boot-partitions");
3018 if (partitions_count < 0) {
3019 dev_err(dev, "Error parsing boot partition.");
> 3020 return ret;
3021 }
3022
3023 host->nr_boot_partitions = partitions_count / 2;
3024 host->boot_partitions = devm_kcalloc(dev, host->nr_boot_partitions,
3025 sizeof(*host->boot_partitions), GFP_KERNEL);
3026 if (!host->boot_partitions)
3027 return -ENOMEM;
3028
3029 for (i = 0, j = 0; i < host->nr_boot_partitions; i++, j += 2) {
3030 boot_partition = &host->boot_partitions[i];
3031
3032 ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j,
3033 &boot_partition->page_offset);
3034 if (ret) {
3035 dev_err(dev, "Error parsing boot partition offset at index %d", i);
3036 return ret;
3037 }
3038
3039 if (boot_partition->page_offset % mtd->writesize) {
3040 dev_err(dev, "Boot partition offset not multiple of writesize at index %i",
3041 i);
3042 return -EINVAL;
3043 }
3044 /* Convert offset to nand pages */
3045 boot_partition->page_offset /= mtd->writesize;
3046
3047 ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j + 1,
3048 &boot_partition->page_size);
3049 if (ret) {
3050 dev_err(dev, "Error parsing boot partition size at index %d", i);
3051 return ret;
3052 }
3053
3054 if (boot_partition->page_size % mtd->writesize) {
3055 dev_err(dev, "Boot partition size not multiple of writesize at index %i",
3056 i);
3057 return -EINVAL;
3058 }
3059 /* Convert size to nand pages */
3060 boot_partition->page_size /= mtd->writesize;
3061 }
3062
3063 return 0;
3064 }
3065
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c index 1a77542c6d67..06ee9a836a3b 100644 --- a/drivers/mtd/nand/raw/qcom_nandc.c +++ b/drivers/mtd/nand/raw/qcom_nandc.c @@ -80,8 +80,10 @@ #define DISABLE_STATUS_AFTER_WRITE 4 #define CW_PER_PAGE 6 #define UD_SIZE_BYTES 9 +#define UD_SIZE_BYTES_MASK GENMASK(18, 9) #define ECC_PARITY_SIZE_BYTES_RS 19 #define SPARE_SIZE_BYTES 23 +#define SPARE_SIZE_BYTES_MASK GENMASK(26, 23) #define NUM_ADDR_CYCLES 27 #define STATUS_BFR_READ 30 #define SET_RD_MODE_AFTER_STATUS 31 @@ -102,6 +104,7 @@ #define ECC_MODE 4 #define ECC_PARITY_SIZE_BYTES_BCH 8 #define ECC_NUM_DATA_BYTES 16 +#define ECC_NUM_DATA_BYTES_MASK GENMASK(25, 16) #define ECC_FORCE_CLK_OPEN 30 /* NAND_DEV_CMD1 bits */ @@ -418,6 +421,19 @@ struct qcom_nand_controller { const struct qcom_nandc_props *props; }; +/* + * NAND special boot partitions + * + * @page_offset: offset of the partition where spare data is not protected + * by ECC (value in pages) + * @page_offset: size of the partition where spare data is not protected + * by ECC (value in pages) + */ +struct qcom_nand_boot_partition { + u32 page_offset; + u32 page_size; +}; + /* * NAND chip structure * @@ -444,6 +460,13 @@ struct qcom_nand_controller { * @cfg0, cfg1, cfg0_raw..: NANDc register configurations needed for * ecc/non-ecc mode for the current nand flash * device + * + * @codeword_fixup: keep track of the current layout used by + * the driver for read/write operation. + * @nr_boot_partitions: count of the boot partitions where spare data is not + * protected by ECC + * @boot_pages: array of boot partitions where offset and size of the + * boot partitions are stored */ struct qcom_nand_host { struct nand_chip chip; @@ -466,6 +489,10 @@ struct qcom_nand_host { u32 ecc_bch_cfg; u32 clrflashstatus; u32 clrreadstatus; + + bool codeword_fixup; + int nr_boot_partitions; + struct qcom_nand_boot_partition *boot_partitions; }; /* @@ -475,6 +502,7 @@ struct qcom_nand_host { * @is_bam - whether NAND controller is using BAM * @is_qpic - whether NAND CTRL is part of qpic IP * @qpic_v2 - flag to indicate QPIC IP version 2 + * @use_codeword_fixup - whether NAND has different layout for boot partitions * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset */ struct qcom_nandc_props { @@ -482,6 +510,7 @@ struct qcom_nandc_props { bool is_bam; bool is_qpic; bool qpic_v2; + bool use_codeword_fixup; u32 dev_cmd_reg_start; }; @@ -1701,7 +1730,7 @@ qcom_nandc_read_cw_raw(struct mtd_info *mtd, struct nand_chip *chip, data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); oob_size1 = host->bbm_size; - if (qcom_nandc_is_last_cw(ecc, cw)) { + if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) { data_size2 = ecc->size - data_size1 - ((ecc->steps - 1) * 4); oob_size2 = (ecc->steps * 4) + host->ecc_bytes_hw + @@ -1782,7 +1811,7 @@ check_for_erased_page(struct qcom_nand_host *host, u8 *data_buf, } for_each_set_bit(cw, &uncorrectable_cws, ecc->steps) { - if (qcom_nandc_is_last_cw(ecc, cw)) { + if (qcom_nandc_is_last_cw(ecc, cw) && !host->codeword_fixup) { data_size = ecc->size - ((ecc->steps - 1) * 4); oob_size = (ecc->steps * 4) + host->ecc_bytes_hw; } else { @@ -1940,7 +1969,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf, for (i = 0; i < ecc->steps; i++) { int data_size, oob_size; - if (qcom_nandc_is_last_cw(ecc, i)) { + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { data_size = ecc->size - ((ecc->steps - 1) << 2); oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + host->spare_bytes; @@ -2037,6 +2066,55 @@ static int copy_last_cw(struct qcom_nand_host *host, int page) return ret; } +static bool +qcom_nandc_is_boot_page(struct qcom_nand_host *host, int page) +{ + struct qcom_nand_boot_partition *boot_partition; + u32 start, end; + int i; + + for (i = 0; i < host->nr_boot_partitions; i++) { + boot_partition = &host->boot_partitions[i]; + start = boot_partition->page_offset; + end = start + boot_partition->page_size; + + /* Boot pages are normally at the start of + * the nand in various partition. + * Check the page from the boot page end first + * to save one extra check and optimize this + * in case real no-boot partition are used. + */ + if (page < end && page >= start) + return true; + } + + return false; +} + +static void +qcom_nandc_codeword_fixup(struct qcom_nand_host *host, int page) +{ + bool codeword_fixup = qcom_nandc_is_boot_page(host, page); + + /* Skip conf write if we are already in the correct mode */ + if (codeword_fixup == host->codeword_fixup) + return; + + host->codeword_fixup = codeword_fixup; + + host->cw_data = codeword_fixup ? 512 : 516; + host->spare_bytes = host->cw_size - host->ecc_bytes_hw - + host->bbm_size - host->cw_data; + + host->cfg0 &= ~(SPARE_SIZE_BYTES_MASK | UD_SIZE_BYTES_MASK); + host->cfg0 |= host->spare_bytes << SPARE_SIZE_BYTES | + host->cw_data << UD_SIZE_BYTES; + + host->ecc_bch_cfg &= ~ECC_NUM_DATA_BYTES_MASK; + host->ecc_bch_cfg |= host->cw_data << ECC_NUM_DATA_BYTES; + host->ecc_buf_cfg = (codeword_fixup ? 0x1ff : 0x203) << NUM_STEPS; +} + /* implements ecc->read_page() */ static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, int oob_required, int page) @@ -2045,6 +2123,9 @@ static int qcom_nandc_read_page(struct nand_chip *chip, uint8_t *buf, struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); u8 *data_buf, *oob_buf = NULL; + if (host->nr_boot_partitions) + qcom_nandc_codeword_fixup(host, page); + nand_read_page_op(chip, page, 0, NULL, 0); data_buf = buf; oob_buf = oob_required ? chip->oob_poi : NULL; @@ -2064,6 +2145,9 @@ static int qcom_nandc_read_page_raw(struct nand_chip *chip, uint8_t *buf, int cw, ret; u8 *data_buf = buf, *oob_buf = chip->oob_poi; + if (host->nr_boot_partitions) + qcom_nandc_codeword_fixup(host, page); + for (cw = 0; cw < ecc->steps; cw++) { ret = qcom_nandc_read_cw_raw(mtd, chip, data_buf, oob_buf, page, cw); @@ -2084,6 +2168,9 @@ static int qcom_nandc_read_oob(struct nand_chip *chip, int page) struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip); struct nand_ecc_ctrl *ecc = &chip->ecc; + if (host->nr_boot_partitions) + qcom_nandc_codeword_fixup(host, page); + clear_read_regs(nandc); clear_bam_transaction(nandc); @@ -2104,6 +2191,9 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf, u8 *data_buf, *oob_buf; int i, ret; + if (host->nr_boot_partitions) + qcom_nandc_codeword_fixup(host, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); clear_read_regs(nandc); @@ -2119,7 +2209,7 @@ static int qcom_nandc_write_page(struct nand_chip *chip, const uint8_t *buf, for (i = 0; i < ecc->steps; i++) { int data_size, oob_size; - if (qcom_nandc_is_last_cw(ecc, i)) { + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { data_size = ecc->size - ((ecc->steps - 1) << 2); oob_size = (ecc->steps << 2) + host->ecc_bytes_hw + host->spare_bytes; @@ -2176,6 +2266,9 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip, u8 *data_buf, *oob_buf; int i, ret; + if (host->nr_boot_partitions) + qcom_nandc_codeword_fixup(host, page); + nand_prog_page_begin_op(chip, page, 0, NULL, 0); clear_read_regs(nandc); clear_bam_transaction(nandc); @@ -2194,7 +2287,7 @@ static int qcom_nandc_write_page_raw(struct nand_chip *chip, data_size1 = mtd->writesize - host->cw_size * (ecc->steps - 1); oob_size1 = host->bbm_size; - if (qcom_nandc_is_last_cw(ecc, i)) { + if (qcom_nandc_is_last_cw(ecc, i) && !host->codeword_fixup) { data_size2 = ecc->size - data_size1 - ((ecc->steps - 1) << 2); oob_size2 = (ecc->steps << 2) + host->ecc_bytes_hw + @@ -2254,6 +2347,9 @@ static int qcom_nandc_write_oob(struct nand_chip *chip, int page) int data_size, oob_size; int ret; + if (host->nr_boot_partitions) + qcom_nandc_codeword_fixup(host, page); + host->use_ecc = true; clear_bam_transaction(nandc); @@ -2902,6 +2998,71 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc) static const char * const probes[] = { "cmdlinepart", "ofpart", "qcomsmem", NULL }; +static int qcom_nand_host_parse_boot_partitions(struct qcom_nand_controller *nandc, + struct qcom_nand_host *host, + struct device_node *dn) +{ + struct nand_chip *chip = &host->chip; + struct mtd_info *mtd = nand_to_mtd(chip); + struct qcom_nand_boot_partition *boot_partition; + struct device *dev = nandc->dev; + int partitions_count, i, j, ret; + + if (!nandc->props->use_codeword_fixup) + return 0; + + if (!of_find_property(dn, "qcom,boot-partitions", NULL)) + return 0; + + partitions_count = of_property_count_u32_elems(dn, "qcom,boot-partitions"); + if (partitions_count < 0) { + dev_err(dev, "Error parsing boot partition."); + return ret; + } + + host->nr_boot_partitions = partitions_count / 2; + host->boot_partitions = devm_kcalloc(dev, host->nr_boot_partitions, + sizeof(*host->boot_partitions), GFP_KERNEL); + if (!host->boot_partitions) + return -ENOMEM; + + for (i = 0, j = 0; i < host->nr_boot_partitions; i++, j += 2) { + boot_partition = &host->boot_partitions[i]; + + ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j, + &boot_partition->page_offset); + if (ret) { + dev_err(dev, "Error parsing boot partition offset at index %d", i); + return ret; + } + + if (boot_partition->page_offset % mtd->writesize) { + dev_err(dev, "Boot partition offset not multiple of writesize at index %i", + i); + return -EINVAL; + } + /* Convert offset to nand pages */ + boot_partition->page_offset /= mtd->writesize; + + ret = of_property_read_u32_index(dn, "qcom,boot-partitions", j + 1, + &boot_partition->page_size); + if (ret) { + dev_err(dev, "Error parsing boot partition size at index %d", i); + return ret; + } + + if (boot_partition->page_size % mtd->writesize) { + dev_err(dev, "Boot partition size not multiple of writesize at index %i", + i); + return -EINVAL; + } + /* Convert size to nand pages */ + boot_partition->page_size /= mtd->writesize; + } + + return 0; +} + static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, struct qcom_nand_host *host, struct device_node *dn) @@ -2970,6 +3131,8 @@ static int qcom_nand_host_init_and_register(struct qcom_nand_controller *nandc, if (ret) nand_cleanup(chip); + qcom_nand_host_parse_boot_partitions(nandc, host, dn); + return ret; } @@ -3135,6 +3298,7 @@ static int qcom_nandc_remove(struct platform_device *pdev) static const struct qcom_nandc_props ipq806x_nandc_props = { .ecc_modes = (ECC_RS_4BIT | ECC_BCH_8BIT), .is_bam = false, + .use_codeword_fixup = true, .dev_cmd_reg_start = 0x0, };
IPQ8064 nand have special pages where a different layout scheme is used. These special page are used by boot partition and on reading them lots of warning are reported about wrong ECC data and if written to results in broken data and not bootable device. The layout scheme used by these special page consist in using 512 bytes as the codeword size (even for the last codeword) while writing to CFG0 register. This forces the NAND controller to unprotect the 4 bytes of spare data. Since the kernel is unaware of this different layout for these special page, it does try to protect the spare data too during read/write and warn about CRC errors. Add support for this by permitting the user to declare these special pages in dts by declaring offset and size of the partition. The driver internally will convert these value to nand pages. On user read/write the page is checked and if it's a boot page the correct layout is used. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/mtd/nand/raw/qcom_nandc.c | 174 +++++++++++++++++++++++++++++- 1 file changed, 169 insertions(+), 5 deletions(-)