@@ -53,6 +53,93 @@ properties:
vdda33-supply:
description: phandle to the regulator 3.3V supply node.
+ qcom,hs-disconnect-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This adjusts the voltage level for the threshold used to
+ detect a disconnect event at the host. Possible values are.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,squelch-detector-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This adjusts the voltage level for the threshold used to
+ detect valid high-speed data.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,hs-amplitude-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This adjusts the high-speed DC level voltage.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,pre-emphasis-duration-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This signal controls the duration for which the
+ HS pre-emphasis current is sourced onto DP<#> or DM<#>.
+ The HS Transmitter pre-emphasis duration is defined in terms of
+ unit amounts. One unit of pre-emphasis duration is approximately
+ 650 ps and is defined as 1X pre-emphasis duration.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,pre-emphasis-amplitude-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This signal controls the amount of current sourced to
+ DP<#> and DM<#> after a J-to-K or K-to-J transition.
+ The HS Transmitter pre-emphasis current is defined in terms of unit
+ amounts. One unit amount is approximately 2 mA and is defined as
+ 1X pre-emphasis current.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,hs-rise-fall-time-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This adjusts the rise/fall times of the high-speed waveform.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,hs-crossover-voltage:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This adjusts the voltage at which the DP<#> and DM<#>
+ signals cross while transmitting in HS mode.
+ The values defined are in milli volts. The hardware accepts only
+ discrete values. The value closest to the provided input will be
+ chosen as the override value for this param.
+
+ qcom,hs-output-impedance:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ In some applications, there can be significant series resistance
+ on the D+ and D- paths between the transceiver and cable. This adjusts
+ the driver source impedance to compensate for added series
+ resistance on the USB. The values defined are in milliohms.
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
+ qcom,ls-fs-output-impedance-bps:
+ $ref: /schemas/types.yaml#/definitions/int32
+ description:
+ This adjusts the low- and full-speed single-ended source
+ impedance while driving high. The following adjustment values are based
+ on nominal process, voltage, and temperature.
+ The values defined are in multiples of basis points (1bp = 0.01%).
+ The hardware accepts only discrete values. The value closest to the
+ provided input will be chosen as the override value for this param.
+
required:
- compatible
- reg