@@ -1119,9 +1119,21 @@ void brcmf_sdio_wowl_config(struct device *dev, bool enabled)
{
struct brcmf_bus *bus_if = dev_get_drvdata(dev);
struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;
+ mmc_pm_flag_t pm_caps = sdio_get_host_pm_caps(sdiodev->func1);
- brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
- sdiodev->wowl_enabled = enabled;
+ /* Power must be preserved to be able to support WOWL. */
+ if (!(pm_caps & MMC_PM_KEEP_POWER))
+ goto notsup;
+
+ if (sdiodev->settings->bus.sdio.oob_irq_supported ||
+ pm_caps & MMC_PM_WAKE_SDIO_IRQ) {
+ sdiodev->wowl_enabled = enabled;
+ brcmf_dbg(SDIO, "Configuring WOWL, enabled=%d\n", enabled);
+ return;
+ }
+
+notsup:
+ brcmf_dbg(SDIO, "WOWL not supported\n");
}
#ifdef CONFIG_PM_SLEEP
@@ -1130,7 +1142,7 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
struct sdio_func *func;
struct brcmf_bus *bus_if;
struct brcmf_sdio_dev *sdiodev;
- mmc_pm_flag_t pm_caps, sdio_flags;
+ mmc_pm_flag_t sdio_flags;
int ret = 0;
func = container_of(dev, struct sdio_func, dev);
@@ -1142,20 +1154,15 @@ static int brcmf_ops_sdio_suspend(struct device *dev)
bus_if = dev_get_drvdata(dev);
sdiodev = bus_if->bus_priv.sdio;
- pm_caps = sdio_get_host_pm_caps(func);
-
- if (pm_caps & MMC_PM_KEEP_POWER) {
- /* preserve card power during suspend */
+ if (sdiodev->wowl_enabled) {
brcmf_sdiod_freezer_on(sdiodev);
brcmf_sdio_wd_timer(sdiodev->bus, 0);
sdio_flags = MMC_PM_KEEP_POWER;
- if (sdiodev->wowl_enabled) {
- if (sdiodev->settings->bus.sdio.oob_irq_supported)
- enable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
- else
- sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
- }
+ if (sdiodev->settings->bus.sdio.oob_irq_supported)
+ enable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
+ else
+ sdio_flags |= MMC_PM_WAKE_SDIO_IRQ;
if (sdio_set_host_pm_flags(sdiodev->func1, sdio_flags))
brcmf_err("Failed to set pm_flags %x\n", sdio_flags);
@@ -1176,21 +1183,19 @@ static int brcmf_ops_sdio_resume(struct device *dev)
struct brcmf_bus *bus_if = dev_get_drvdata(dev);
struct brcmf_sdio_dev *sdiodev = bus_if->bus_priv.sdio;
struct sdio_func *func = container_of(dev, struct sdio_func, dev);
- mmc_pm_flag_t pm_caps = sdio_get_host_pm_caps(func);
int ret = 0;
brcmf_dbg(SDIO, "Enter: F%d\n", func->num);
if (func->num != 2)
return 0;
- if (!(pm_caps & MMC_PM_KEEP_POWER)) {
+ if (!sdiodev->wowl_enabled) {
/* bus was powered off and device removed, probe again */
ret = brcmf_sdiod_probe(sdiodev);
if (ret)
brcmf_err("Failed to probe device on resume\n");
} else {
- if (sdiodev->wowl_enabled &&
- sdiodev->settings->bus.sdio.oob_irq_supported)
+ if (sdiodev->settings->bus.sdio.oob_irq_supported)
disable_irq_wake(sdiodev->settings->bus.sdio.oob_irq_nr);
brcmf_sdiod_freezer_off(sdiodev);
Keeping the power to the SDIO card during system wide suspend, consumes energy. Especially on battery driven embedded systems, this can be a problem. Therefore, let's change the behaviour into allowing the SDIO card to be powered off, unless WOWL is supported and enabled. Note that, the downside from this change, is that during system resume the SDIO card needs to be re-initialized and the FW must be re-programmed. Even if this may take some time to complete, it should we worth it, rather than draining the battery. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> --- Changes in v2: - As pointed out by Yann, the changes for the resume path was missing, so I have added that too. Again, please note that, I have only compile-tested this patch, so I am relying on help from Yann and others to run tests on real HW. Kind regards Ulf Hansson --- .../broadcom/brcm80211/brcmfmac/bcmsdh.c | 39 +++++++++++-------- 1 file changed, 22 insertions(+), 17 deletions(-)