| Message ID | ce8ae6b199fa244315a008ae31891a808ca1948d.1631174218.git.geert+renesas@glider.be |
|---|---|
| State | Accepted |
| Commit | eb7d7b00d068bbf23c555a3589834753c3a1345b |
| Headers | show |
| Series | renesas: Add compatible properties to Ethernet PHY nodes | expand |
diff --git a/arch/arm/boot/dts/iwg20d-q7-common.dtsi b/arch/arm/boot/dts/iwg20d-q7-common.dtsi index bc857676d19104a1..849034a49a3f98e2 100644 --- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi +++ b/arch/arm/boot/dts/iwg20d-q7-common.dtsi @@ -158,6 +158,8 @@ &avb { status = "okay"; phy3: ethernet-phy@3 { + compatible = "ethernet-phy-id0022.1622", + "ethernet-phy-ieee802.3-c22"; reg = <3>; micrel,led-mode = <1>; }; diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts index 94bf8a116b5242a9..a5a79cdbcd0ee09b 100644 --- a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts +++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts @@ -175,6 +175,8 @@ &avb { status = "okay"; phy3: ethernet-phy@3 { + compatible = "ethernet-phy-id0022.1622", + "ethernet-phy-ieee802.3-c22"; reg = <3>; micrel,led-mode = <1>; }; diff --git a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts index 73bd62d8a929e5da..c105932f642ea517 100644 --- a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts +++ b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts @@ -123,6 +123,8 @@ phy3: ethernet-phy@3 { * On some older versions of the platform (before R4.0) the phy address * may be 1 or 3. The address is fixed to 3 for R4.0 onwards. */ + compatible = "ethernet-phy-id0022.1622", + "ethernet-phy-ieee802.3-c22"; reg = <3>; micrel,led-mode = <1>; }; diff --git a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts index 8ac61b50aec03190..b024621c998103b2 100644 --- a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts +++ b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts @@ -79,6 +79,8 @@ &avb { status = "okay"; phy3: ethernet-phy@3 { + compatible = "ethernet-phy-id0022.1622", + "ethernet-phy-ieee802.3-c22"; reg = <3>; interrupt-parent = <&gpio5>; interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
Add compatible values to Ethernet PHY subnodes representing Micrel KSZ9031 PHYs on RZ/G1 boards. This allows software to identify the PHY model at any time, regardless of the state of the PHY reset line. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- I could not verify the PHY revision number (least significant nibble of the ID), due to lack of hardware. --- arch/arm/boot/dts/iwg20d-q7-common.dtsi | 2 ++ arch/arm/boot/dts/r8a7742-iwg21d-q7.dts | 2 ++ arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts | 2 ++ arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts | 2 ++ 4 files changed, 8 insertions(+)