diff mbox series

arm64: dts: qcom: Add sc7180-trogdor-homestar

Message ID 20210909122053.1.Ieafda79b74f74a2b15ed86e181c06a3060706ec5@changeid
State Accepted
Commit be0416a3f9173aaa1f946ee0dbc4c146a295834d
Headers show
Series arm64: dts: qcom: Add sc7180-trogdor-homestar | expand

Commit Message

Matthias Kaehlcke Sept. 9, 2021, 7:21 p.m. UTC
Homestar is a trogdor variant. The DT bits are essentially the same as
in the downstream tree, except for:

- skip -rev0 and rev1 which were early builds and have their issues,
  it's not very useful to support them upstream
- don't include the .dtsi for the MIPI cameras, which doesn't exist
  upstream

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
---

 arch/arm64/boot/dts/qcom/Makefile             |   2 +
 .../dts/qcom/sc7180-trogdor-homestar-r2.dts   |  20 ++
 .../dts/qcom/sc7180-trogdor-homestar-r3.dts   |  15 +
 .../dts/qcom/sc7180-trogdor-homestar.dtsi     | 335 ++++++++++++++++++
 4 files changed, 372 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi

Comments

Doug Anderson Sept. 10, 2021, 9:19 p.m. UTC | #1
Hi,

On Thu, Sep 9, 2021 at 12:21 PM Matthias Kaehlcke <mka@chromium.org> wrote:
>

> Homestar is a trogdor variant. The DT bits are essentially the same as

> in the downstream tree, except for:

>

> - skip -rev0 and rev1 which were early builds and have their issues,

>   it's not very useful to support them upstream

> - don't include the .dtsi for the MIPI cameras, which doesn't exist

>   upstream

>

> Signed-off-by: Matthias Kaehlcke <mka@chromium.org>

> ---

>

>  arch/arm64/boot/dts/qcom/Makefile             |   2 +

>  .../dts/qcom/sc7180-trogdor-homestar-r2.dts   |  20 ++

>  .../dts/qcom/sc7180-trogdor-homestar-r3.dts   |  15 +

>  .../dts/qcom/sc7180-trogdor-homestar.dtsi     | 335 ++++++++++++++++++

>  4 files changed, 372 insertions(+)


Reviewed-by: Douglas Anderson <dianders@chromium.org>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4f0597091976..91ec59c291c7 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -41,6 +41,8 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r3-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r2.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1-kb.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
new file mode 100644
index 000000000000..db6c2da67cea
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
@@ -0,0 +1,20 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-homestar.dtsi"
+
+/ {
+	model = "Google Homestar (rev2)";
+	compatible = "google,homestar-rev2","google,homestar-rev23", "qcom,sc7180";
+};
+
+&panel {
+	/delete-property/hpd-gpios;
+	no-hpd;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
new file mode 100644
index 000000000000..3fd8aa5bb7a6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
@@ -0,0 +1,15 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-homestar.dtsi"
+
+/ {
+	model = "Google Homestar (rev3+)";
+	compatible = "google,homestar", "qcom,sc7180";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
new file mode 100644
index 000000000000..cd3054226865
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
@@ -0,0 +1,335 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+#include "sc7180.dtsi"
+
+ap_ec_spi: &spi6 {};
+ap_h1_spi: &spi0 {};
+
+#include "sc7180-trogdor.dtsi"
+
+/ {
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+
+	max98360a_1: max98360a_1 {
+		compatible = "maxim,max98360a";
+		#sound-dai-cells = <0>;
+	};
+
+	max98360a_2: max98360a_2 {
+		compatible = "maxim,max98360a";
+		#sound-dai-cells = <0>;
+	};
+
+	max98360a_3: max98360a_3 {
+		compatible = "maxim,max98360a";
+		#sound-dai-cells = <0>;
+	};
+
+	pp3300_touch: pp3300-touch {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_touch";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_pp3300_touch>;
+
+		vin-supply = <&pp3300_a>;
+	};
+
+	thermal-zones {
+		skin_temp_thermal: skin-temp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm6150_adc_tm 1>;
+			sustainable-power = <814>;
+
+			trips {
+				skin_temp_alert0: trip-point0 {
+					temperature = <55000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				skin_temp_alert1: trip-point1 {
+					temperature = <58000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				skin-temp-crit {
+					temperature = <73000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&skin_temp_alert0>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&skin_temp_alert1>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
+
+&ap_tp_i2c {
+	status = "disabled";
+};
+
+ap_ts_pen_1v8: &i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@14 {
+		compatible = "goodix,gt7375p";
+		reg = <0x14>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&pp3300_touch>;
+	};
+};
+
+/* Panel controls backlight over aux channel */
+
+&backlight {
+	status = "disabled";
+};
+
+&camcc {
+	status = "okay";
+};
+
+&panel {
+	compatible = "samsung,atna33xc20";
+	enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+	/delete-property/ backlight;
+};
+
+&pm6150_adc {
+	skin-temp-thermistor@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm6150_adc_tm {
+	status = "okay";
+
+	skin-temp-thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pp3300_dx_edp {
+	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+};
+
+&secondary_mi2s {
+	qcom,playback-sd-lines = <0 1>;
+};
+
+&sound_multimedia1_codec {
+	sound-dai = <&max98360a>, <&max98360a_1>, <&max98360a_2>, <&max98360a_3> ;
+};
+
+&wifi {
+	qcom,ath10k-calibration-variant = "GO_HOMESTAR";
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+&en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio67";
+	};
+
+	pinconf {
+		pins = "gpio67";
+	};
+};
+
+&sec_mi2s_active{
+	pinmux {
+		pins = "gpio49", "gpio50", "gpio51", "gpio52";
+		function = "mi2s_1";
+	};
+};
+
+&ts_reset_l {
+	pinconf {
+		/*
+		 * We want reset state by default and it will be up to the
+		 * driver to disable this when it's ready.
+		 */
+		output-low;
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "HUB_RST_L",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "EDP_BRIJ_IRQ",
+			  "AP_EDP_BKLTEN",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_CLK",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "UF_CAM_SDA",
+			  "UF_CAM_SCL",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "AVEE_LCD_EN",
+			  "",
+			  "AMP_EN",
+			  "AMP_EN2",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+			  "SEL_LCM",
+			  "HP_IRQ",
+			  "WF_CAM_RST_L",
+			  "UF_CAM_RST_L",
+			  "AP_BRD_ID2",
+			  "BRIJ_SUSPEND",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+			  "BT_UART_TXD",
+			  "BT_UART_RXD",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "AMP_BCLK",
+			  "AMP_LRCLK",
+			  "AMP_DIN",
+			  "AMP_DIN_2",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "EN_PP3300_DX_EDP",
+			  "AP_SPI_CS0_L",
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "",
+			  "WLAN_SW_CTRL",
+			  "",
+			  "REPORT_E",
+			  "VDD_RESET_1.8V",
+			  "ID0",
+			  "",
+			  "ID1",
+			  "AVDD_LCD_EN",
+			  "MIPI_1.8V_EN",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "",
+			  "PP1800_MIPI_SW_EN",
+			  "EN_PP3300_TOUCH",
+			  "",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "SDM_GRFC_3",
+			  "",
+			  "",
+			  "BOOT_CONFIG_4",
+			  "BOOT_CONFIG_2",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "EDP_BRIJ_EN",
+			  "",
+			  "",
+			  "BOOT_CONFIG_3",
+			  "WCI2_LTE_COEX_TXD",
+			  "WCI2_LTE_COEX_RXD",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "FORCED_USB_BOOT_POL",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+
+	en_pp3300_touch: en-pp3300-touch {
+		pinmux {
+			pins = "gpio87";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio87";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};