diff mbox series

[v2] arm64: dts: qcom: sdm660: Add initial IFC6560 board

Message ID 20210825221110.1498718-1-bjorn.andersson@linaro.org
State New
Headers show
Series [v2] arm64: dts: qcom: sdm660: Add initial IFC6560 board | expand

Commit Message

Bjorn Andersson Aug. 25, 2021, 10:11 p.m. UTC
The IFC6560 is a board from Inforce Computing, built around the SDA660
SoC. This patch describes core clocks, some regulators from the two
PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.

The regulator settings are inherited from prior work by Konrad Dybcio
and AngeloGioacchino Del Regno.

Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v1:
- Fixed typo 29p5 -> 2p95 in two regulators.

 arch/arm64/boot/dts/qcom/Makefile           |   1 +
 arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts | 279 ++++++++++++++++++++
 2 files changed, 280 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts

Comments

Konrad Dybcio Aug. 27, 2021, 11:05 p.m. UTC | #1
On 26.08.2021 00:11, Bjorn Andersson wrote:
> The IFC6560 is a board from Inforce Computing, built around the SDA660

> SoC. This patch describes core clocks, some regulators from the two

> PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.

>

> The regulator settings are inherited from prior work by Konrad Dybcio

> and AngeloGioacchino Del Regno.

>

> Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>

> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>

> ---

>

> Changes since v1:

> - Fixed typo 29p5 -> 2p95 in two regulators.

>

>  arch/arm64/boot/dts/qcom/Makefile           |   1 +

>  arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts | 279 ++++++++++++++++++++

>  2 files changed, 280 insertions(+)

>  create mode 100644 arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts

>

> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile

> index 70516508be56..88abcfeb4d38 100644

> --- a/arch/arm64/boot/dts/qcom/Makefile

> +++ b/arch/arm64/boot/dts/qcom/Makefile

> @@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb

>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb

>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-voyager.dtb

>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm636-sony-xperia-ganges-mermaid.dtb

> +dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-ifc6560.dtb

>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-xiaomi-lavender.dtb

>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb

>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb

> diff --git a/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts b/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts

> new file mode 100644

> index 000000000000..bfb17711ab55

> --- /dev/null

> +++ b/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts

> @@ -0,0 +1,279 @@

> +// SPDX-License-Identifier: BSD-3-Clause

> +/*

> + * Copyright (c) 2021, Linaro Ltd.

> + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org>

> + * Copyright (c) 2020, AngeloGioacchino Del Regno

> + *                     <angelogioacchino.delregno@somainline.org>

> + */

> +

> +/dts-v1/;

> +

> +#include "sdm660.dtsi"

> +#include "pm660.dtsi"

> +#include "pm660l.dtsi"

> +

> +/ {

> +	model = "Inforce 6560 Single Board Computer";

> +	compatible = "inforce,ifc6560", "qcom,sdm660";

> +

> +	aliases {

> +		serial0 = &blsp1_uart2;

> +		serial1 = &blsp2_uart1;

> +	};

> +

> +	chosen {

> +		stdout-path = "serial0:115200n8";

> +	};

> +

> +	reserved-memory {

> +		#address-cells = <2>;

> +		#size-cells = <2>;

> +		ranges;

> +	};


This is already defined in sdm630.dtsi.


> +

> +	vph_pwr: vph-pwr-regulator {

> +		compatible = "regulator-fixed";

> +		regulator-name = "vph_pwr";

> +	};


No voltage range?


> +

> +	v3p3_bck_bst: v3p3-bck-bst-regulator {

> +		compatible = "regulator-fixed";

> +		regulator-name = "v3p3_bck_bst";

> +

> +		regulator-min-microvolt = <3300000>;

> +		regulator-max-microvolt = <3300000>;

> +

> +		vin-supply = <&vph_pwr>;

> +	};

> +

> +	v1p2_ldo: v1p2-ldo-regulator {

> +		compatible = "regulator-fixed";

> +		regulator-name = "v1p2_ldo";

> +

> +		regulator-min-microvolt = <1200000>;

> +		regulator-max-microvolt = <1200000>;

> +

> +		vin-supply = <&vph_pwr>;

> +	};

> +

> +	v5p0_boost: v5p0-boost-regulator {

> +		compatible = "regulator-fixed";

> +		regulator-name = "v5p0_boost";

> +

> +		regulator-min-microvolt = <5000000>;

> +		regulator-max-microvolt = <5000000>;

> +

> +		vin-supply = <&vph_pwr>;

> +	};

> +};

> +

> +&adsp_pil {

> +	firmware-name = "qcom/inforce/ifc6560/adsp.mbn";

> +};

> +

> +&blsp1_uart2 {

> +	status = "okay";

> +	pinctrl-names = "default";

> +	pinctrl-0 = <&uart_active>;

> +};

> +

> +&blsp2_uart1 {

> +	status = "okay";

> +

> +	bluetooth {

> +		compatible = "qcom,wcn3990-bt";

> +

> +		vddio-supply = <&vreg_l13a_1p8>;

> +		vddxo-supply = <&vreg_l9a_1p8>;

> +		vddrf-supply = <&vreg_l6a_1p3>;

> +		vddch0-supply = <&vreg_l19a_3p3>;

> +		max-speed = <3200000>;

> +	};

> +};

> +

> +&rpm_requests {

> +	pm660-regulators {

> +		compatible = "qcom,rpm-pm660-regulators";

> +

> +		vdd_s1-supply = <&vph_pwr>;

> +		vdd_s2-supply = <&vph_pwr>;

> +		vdd_s3-supply = <&vph_pwr>;

> +		vdd_s4-supply = <&vph_pwr>;

> +		vdd_s5-supply = <&vph_pwr>;

> +		vdd_s6-supply = <&vph_pwr>;

> +

> +		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;

> +		vdd_l2_l3-supply = <&vreg_s2b_1p05>;

> +		vdd_l5-supply = <&vreg_s2b_1p05>;

> +		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;

> +		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;

> +

> +		vreg_s4a_2p04: s4 {

> +			regulator-min-microvolt = <2040000>;

> +			regulator-max-microvolt = <2040000>;

> +			regulator-enable-ramp-delay = <200>;

> +			regulator-ramp-delay = <0>;

> +			regulator-always-on;

> +		};

> +

> +		vreg_s5a_1p35: s5 {

> +			regulator-min-microvolt = <1224000>;

> +			regulator-max-microvolt = <1350000>;

> +			regulator-enable-ramp-delay = <200>;

> +			regulator-ramp-delay = <0>;

> +		};

> +

> +		vreg_l6a_1p3: l6 {

> +			regulator-min-microvolt = <1304000>;

> +			regulator-max-microvolt = <1368000>;

> +			regulator-allow-set-load;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +		};

> +

> +		vreg_l8a_1p8: l8 {

> +			regulator-min-microvolt = <1800000>;

> +			regulator-max-microvolt = <1800000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +			regulator-system-load = <325000>;

> +			regulator-allow-set-load;

> +		};

> +

> +		vreg_l9a_1p8: l9 {

> +			regulator-min-microvolt = <1804000>;

> +			regulator-max-microvolt = <1896000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +			regulator-allow-set-load;

> +		};

> +

> +		vreg_l13a_1p8: l13 {

> +			/* This gives power to the LPDDR4: never turn it off! */

> +			regulator-min-microvolt = <1800000>;

> +			regulator-max-microvolt = <1944000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +			regulator-boot-on;

> +			regulator-always-on;

> +		};

> +

> +		vreg_l19a_3p3: l19 {

> +			regulator-min-microvolt = <3312000>;

> +			regulator-max-microvolt = <3400000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +			regulator-allow-set-load;

> +		};

> +	};

> +

> +	pm660l-regulators {

> +		compatible = "qcom,rpm-pm660l-regulators";

> +

> +		vdd_s1-supply = <&vph_pwr>;

> +		vdd_s2-supply = <&vph_pwr>;

> +		vdd_s3_s4-supply = <&vph_pwr>;

> +		vdd_s5-supply = <&vph_pwr>;

> +		vdd_s6-supply = <&vph_pwr>;

> +

> +		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;

> +		vdd_l2-supply = <&vreg_bob>;

> +		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;

> +		vdd_l4_l6-supply = <&vreg_bob>;

> +		vdd_bob-supply = <&vph_pwr>;

> +

> +		vreg_s2b_1p05: s2 {

> +			regulator-min-microvolt = <1050000>;

> +			regulator-max-microvolt = <1050000>;

> +			regulator-enable-ramp-delay = <200>;

> +			regulator-ramp-delay = <0>;

> +		};

> +

> +		vreg_l2b_2p95: l2 {

> +			/*

> +			 * This regulator supports 1.648 - 3.104V on this board

> +			 * but we set a max voltage of anything less than 2.7V

> +			 * to satisfy a condition in sdhci.c that will disable

> +			 * 3.3V SDHCI signaling, which happens to be not really

> +			 * supported on the Xperia Nile/Ganges platform.

> +			 */


That's not Nile/Ganges ;)


> +			regulator-min-microvolt = <1648000>;

> +			regulator-max-microvolt = <2696000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +			regulator-allow-set-load;

> +		};

> +

> +		vreg_l4b_2p95: l4 {

> +			regulator-min-microvolt = <2944000>;

> +			regulator-max-microvolt = <2952000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +

> +			regulator-min-microamp = <200>;

> +			regulator-max-microamp = <600000>;

> +			regulator-system-load = <570000>;

> +			regulator-allow-set-load;

> +		};

> +

> +		vreg_l5b_2p95: l5 {

> +			/*

> +			 * Downstream specifies a range of 1721-3600mV,

> +			 * but the only assigned consumers are SDHCI2 VMMC

> +			 * and Coresight QPDI that both request pinned 2.95V.

> +			 * Tighten the range to 1.8-3.328 (closest to 3.3) to

> +			 * make the mmc driver happy.

> +			 */


Please validate whether this voltage mess also concerns your board.


> +			regulator-min-microvolt = <1800000>;

> +			regulator-max-microvolt = <3328000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +			regulator-allow-set-load;

> +			regulator-system-load = <800000>;

> +		};

> +

> +		vreg_l8b_3p3: l8 {

> +			regulator-min-microvolt = <2800000>;

> +			regulator-max-microvolt = <3400000>;

> +			regulator-enable-ramp-delay = <250>;

> +			regulator-ramp-delay = <0>;

> +		};

> +

> +		vreg_bob: bob {

> +			regulator-min-microvolt = <3304000>;

> +			regulator-max-microvolt = <3624000>;

> +			regulator-enable-ramp-delay = <500>;

> +			regulator-ramp-delay = <0>;

> +		};

> +	};

> +};

> +

> +&sdhc_1 {

> +	status = "okay";

> +	supports-cqe;

> +

> +	mmc-ddr-1_8v;

> +	mmc-hs400-1_8v;

> +	mmc-hs400-enhanced-strobe;

> +

> +	vmmc-supply = <&vreg_l4b_2p95>;

> +	vqmmc-supply = <&vreg_l8a_1p8>;

> +};

> +

> +&sdhc_2 {

> +	status = "okay";

> +

> +	vmmc-supply = <&vreg_l5b_2p95>;

> +	vqmmc-supply = <&vreg_l2b_2p95>;

> +};

> +

> +&tlmm {

> +	gpio-reserved-ranges = <0 4>, <8 4>;

> +

> +	uart_active: uart-active-state {

> +		pins = "gpio4", "gpio5";

> +		function = "blsp_uart2";

> +		drive-strength = <2>;

> +		bias-disable;

> +	};


That's identical to blsp1_uart2_default from sdm630.dtsi. While I agree

hardcoding pinctrl-names to "default" is a good idea, should a sleep state

be added to the SoC DTSI (so that it doesn't get passed in here unvalidated),

I don't think you need to redefine this one.


> +};

>


Konrad
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 70516508be56..88abcfeb4d38 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -73,6 +73,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-voyager.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm636-sony-xperia-ganges-mermaid.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-ifc6560.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-xiaomi-lavender.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
diff --git a/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts b/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts
new file mode 100644
index 000000000000..bfb17711ab55
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm660-ifc6560.dts
@@ -0,0 +1,279 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org>
+ * Copyright (c) 2020, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm660.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/ {
+	model = "Inforce 6560 Single Board Computer";
+	compatible = "inforce,ifc6560", "qcom,sdm660";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+	};
+
+	v3p3_bck_bst: v3p3-bck-bst-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v3p3_bck_bst";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v1p2_ldo: v1p2-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p2_ldo";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v5p0_boost: v5p0-boost-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v5p0_boost";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pil {
+	firmware-name = "qcom/inforce/ifc6560/adsp.mbn";
+};
+
+&blsp1_uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart_active>;
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_l13a_1p8>;
+		vddxo-supply = <&vreg_l9a_1p8>;
+		vddrf-supply = <&vreg_l6a_1p3>;
+		vddch0-supply = <&vreg_l19a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&rpm_requests {
+	pm660-regulators {
+		compatible = "qcom,rpm-pm660-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
+		vdd_l2_l3-supply = <&vreg_s2b_1p05>;
+		vdd_l5-supply = <&vreg_s2b_1p05>;
+		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
+		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
+
+		vreg_s4a_2p04: s4 {
+			regulator-min-microvolt = <2040000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+		};
+
+		vreg_s5a_1p35: s5 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l6a_1p3: l6 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1368000>;
+			regulator-allow-set-load;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l8a_1p8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-system-load = <325000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1804000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13a_1p8: l13 {
+			/* This gives power to the LPDDR4: never turn it off! */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1944000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vreg_l19a_3p3: l19 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pm660l-regulators {
+		compatible = "qcom,rpm-pm660l-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
+		vdd_l2-supply = <&vreg_bob>;
+		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
+		vdd_l4_l6-supply = <&vreg_bob>;
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_s2b_1p05: s2 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l2b_2p95: l2 {
+			/*
+			 * This regulator supports 1.648 - 3.104V on this board
+			 * but we set a max voltage of anything less than 2.7V
+			 * to satisfy a condition in sdhci.c that will disable
+			 * 3.3V SDHCI signaling, which happens to be not really
+			 * supported on the Xperia Nile/Ganges platform.
+			 */
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2696000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4b_2p95: l4 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+
+			regulator-min-microamp = <200>;
+			regulator-max-microamp = <600000>;
+			regulator-system-load = <570000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l5b_2p95: l5 {
+			/*
+			 * Downstream specifies a range of 1721-3600mV,
+			 * but the only assigned consumers are SDHCI2 VMMC
+			 * and Coresight QPDI that both request pinned 2.95V.
+			 * Tighten the range to 1.8-3.328 (closest to 3.3) to
+			 * make the mmc driver happy.
+			 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3328000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+			regulator-system-load = <800000>;
+		};
+
+		vreg_l8b_3p3: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3304000>;
+			regulator-max-microvolt = <3624000>;
+			regulator-enable-ramp-delay = <500>;
+			regulator-ramp-delay = <0>;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+	supports-cqe;
+
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+
+	vmmc-supply = <&vreg_l4b_2p95>;
+	vqmmc-supply = <&vreg_l8a_1p8>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&vreg_l5b_2p95>;
+	vqmmc-supply = <&vreg_l2b_2p95>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <8 4>;
+
+	uart_active: uart-active-state {
+		pins = "gpio4", "gpio5";
+		function = "blsp_uart2";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};