@@ -15,6 +15,7 @@
#include <linux/can/dev.h>
#include <linux/can/skb.h>
#include <linux/can/led.h>
+#include <linux/gpio/consumer.h>
#include <linux/of.h>
#define MOD_DESC "CAN device driver interface"
@@ -400,10 +401,69 @@ void close_candev(struct net_device *dev)
}
EXPORT_SYMBOL_GPL(close_candev);
+static int can_set_termination(struct net_device *ndev, u16 term)
+{
+ struct can_priv *priv = netdev_priv(ndev);
+ int set;
+
+ if (term == priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED])
+ set = 1;
+ else
+ set = 0;
+
+ gpiod_set_value(priv->termination_gpio, set);
+
+ return 0;
+}
+
+static int can_get_termination(struct net_device *ndev)
+{
+ struct can_priv *priv = netdev_priv(ndev);
+ struct device *dev = ndev->dev.parent;
+ struct gpio_desc *gpio;
+ u32 term;
+ int ret;
+
+ /* Disabling termination by default is the safe choice: Else if many
+ * bus participants enable it, no communication is possible at all.
+ */
+ gpio = devm_gpiod_get_optional(dev, "termination", GPIOD_OUT_LOW);
+ if (IS_ERR(gpio))
+ return dev_err_probe(dev, PTR_ERR(gpio),
+ "Cannot get termination-gpios\n");
+
+ if (!gpio)
+ return 0;
+
+ ret = device_property_read_u32(dev, "termination-ohms", &term);
+ if (ret) {
+ netdev_err(ndev, "Cannot get termination-ohms: %pe\n",
+ ERR_PTR(ret));
+ return ret;
+ }
+
+ if (term > U16_MAX) {
+ netdev_err(ndev, "Invalid termination-ohms value (%u > %u)\n",
+ term, U16_MAX);
+ return -EINVAL;
+ }
+
+ priv->termination_const_cnt = ARRAY_SIZE(priv->termination_gpio_ohms);
+ priv->termination_const = priv->termination_gpio_ohms;
+ priv->termination_gpio = gpio;
+ priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_DISABLED] =
+ CAN_TERMINATION_DISABLED;
+ priv->termination_gpio_ohms[CAN_TERMINATION_GPIO_ENABLED] = term;
+ priv->do_set_termination = can_set_termination;
+
+ return 0;
+}
+
/* Register the CAN network device */
int register_candev(struct net_device *dev)
{
struct can_priv *priv = netdev_priv(dev);
+ int err;
/* Ensure termination_const, termination_const_cnt and
* do_set_termination consistency. All must be either set or
@@ -419,6 +479,12 @@ int register_candev(struct net_device *dev)
if (!priv->data_bitrate_const != !priv->data_bitrate_const_cnt)
return -EINVAL;
+ if (!priv->termination_const) {
+ err = can_get_termination(dev);
+ if (err)
+ return err;
+ }
+
dev->rtnl_link_ops = &can_link_ops;
netif_carrier_off(dev);
@@ -32,6 +32,12 @@ enum can_mode {
CAN_MODE_SLEEP
};
+enum can_termination_gpio {
+ CAN_TERMINATION_GPIO_DISABLED = 0,
+ CAN_TERMINATION_GPIO_ENABLED,
+ CAN_TERMINATION_GPIO_MAX,
+};
+
/*
* CAN common private data
*/
@@ -55,6 +61,8 @@ struct can_priv {
unsigned int termination_const_cnt;
const u16 *termination_const;
u16 termination;
+ struct gpio_desc *termination_gpio;
+ u16 termination_gpio_ohms[CAN_TERMINATION_GPIO_MAX];
enum can_state state;
For CAN buses to work, a termination resistor has to be present at both ends of the bus. This resistor is usually 120 Ohms, other values may be required for special bus topologies. This patch adds support for a generic GPIO based CAN termination. The resistor value has to be specified via device tree, and it can only be attached to or detached from the bus. By default the termination is not active. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/net/can/dev/dev.c | 66 +++++++++++++++++++++++++++++++++++++++ include/linux/can/dev.h | 8 +++++ 2 files changed, 74 insertions(+)