@@ -521,6 +521,39 @@ config GPIO_ZYNQ
comment "I2C GPIO expanders:"
+config GPIO_ADP5520
+ tristate "GPIO Support for ADP5520 PMIC"
+ depends on PMIC_ADP5520
+ help
+ This option enables support for on-chip GPIO found
+ on Analog Devices ADP5520 PMICs.
+
+config GPIO_ADP5588
+ tristate "ADP5588 I2C GPIO expander"
+ depends on I2C
+ help
+ This option enables support for 18 GPIOs found
+ on Analog Devices ADP5588 GPIO Expanders.
+
+config GPIO_ADP5588_IRQ
+ bool "Interrupt controller support for ADP5588"
+ depends on GPIO_ADP5588=y
+ help
+ Say yes here to enable the adp5588 to be used as an interrupt
+ controller. It requires the driver to be built in the kernel.
+
+config GPIO_ADNP
+ tristate "Avionic Design N-bit GPIO expander"
+ depends on I2C && OF_GPIO
+ select GPIOLIB_IRQCHIP
+ help
+ This option enables support for N GPIOs found on Avionic Design
+ I2C GPIO expanders. The register space will be extended by powers
+ of two, so the controller will need to accommodate for that. For
+ example: if a controller provides 48 pins, 6 registers will be
+ enough to represent all pins, but the driver will assume a
+ register layout for 64 pins (8 registers).
+
config GPIO_ARIZONA
tristate "Wolfson Microelectronics Arizona class devices"
depends on MFD_ARIZONA
@@ -651,18 +684,6 @@ config GPIO_RC5T583
This driver provides the support for driving/reading the gpio pins
of RC5T583 device through standard gpio library.
-config GPIO_SX150X
- bool "Semtech SX150x I2C GPIO expander"
- depends on I2C=y
- select GPIOLIB_IRQCHIP
- default n
- help
- Say yes here to provide support for Semtech SX150-series I2C
- GPIO expanders. Compatible models include:
-
- 8 bits: sx1508q
- 16 bits: sx1509q
-
config GPIO_STMPE
bool "STMPE GPIOs"
depends on MFD_STMPE
@@ -682,6 +703,18 @@ config GPIO_STP_XWAY
Some of the gpios/leds can be auto updated by the soc with dsl and
phy status.
+config GPIO_SX150X
+ bool "Semtech SX150x I2C GPIO expander"
+ depends on I2C=y
+ select GPIOLIB_IRQCHIP
+ default n
+ help
+ Say yes here to provide support for Semtech SX150-series I2C
+ GPIO expanders. Compatible models include:
+
+ 8 bits: sx1508q
+ 16 bits: sx1509q
+
config GPIO_TC3589X
bool "TC3589X GPIOs"
depends on MFD_TC3589X
@@ -731,39 +764,6 @@ config GPIO_WM8994
Say yes here to access the GPIO signals of WM8994 audio hub
CODECs from Wolfson Microelectronics.
-config GPIO_ADP5520
- tristate "GPIO Support for ADP5520 PMIC"
- depends on PMIC_ADP5520
- help
- This option enables support for on-chip GPIO found
- on Analog Devices ADP5520 PMICs.
-
-config GPIO_ADP5588
- tristate "ADP5588 I2C GPIO expander"
- depends on I2C
- help
- This option enables support for 18 GPIOs found
- on Analog Devices ADP5588 GPIO Expanders.
-
-config GPIO_ADP5588_IRQ
- bool "Interrupt controller support for ADP5588"
- depends on GPIO_ADP5588=y
- help
- Say yes here to enable the adp5588 to be used as an interrupt
- controller. It requires the driver to be built in the kernel.
-
-config GPIO_ADNP
- tristate "Avionic Design N-bit GPIO expander"
- depends on I2C && OF_GPIO
- select GPIOLIB_IRQCHIP
- help
- This option enables support for N GPIOs found on Avionic Design
- I2C GPIO expanders. The register space will be extended by powers
- of two, so the controller will need to accommodate for that. For
- example: if a controller provides 48 pins, 6 registers will be
- enough to represent all pins, but the driver will assume a
- register layout for 64 pins (8 registers).
-
comment "PCI GPIO expanders:"
config GPIO_CS5535
Rearrange the I2C GPIO expanders in alphabetic order as already indicated by the comment in the file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- drivers/gpio/Kconfig | 90 ++++++++++++++++++++++++++-------------------------- 1 file changed, 45 insertions(+), 45 deletions(-)