@@ -33,6 +33,8 @@
#define DRIVER_NAME "xiic-i2c"
+#define DYNAMIC_MODE_READ_BROKEN_BIT BIT(0)
+
enum xilinx_i2c_state {
STATE_DONE,
STATE_ERROR,
@@ -63,6 +65,7 @@ enum xiic_endian {
* @dynamic: Mode of controller
* @prev_msg_tx: Previous message is Tx
* @smbus_block_read: Flag to handle block read
+ * @quirks: To hold platform specific bug info
*/
struct xiic_i2c {
struct device *dev;
@@ -82,6 +85,11 @@ struct xiic_i2c {
bool dynamic;
bool prev_msg_tx;
bool smbus_block_read;
+ u32 quirks;
+};
+
+struct xiic_version_data {
+ u32 quirks;
};
#define XIIC_MSB_OFFSET 0
@@ -1032,6 +1040,7 @@ static int xiic_start_xfer(struct xiic_i2c *i2c)
static int xiic_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
{
+ bool broken_read, max_read_len, smbus_blk_read;
struct xiic_i2c *i2c = i2c_get_adapdata(adap);
int err, count;
@@ -1056,13 +1065,22 @@ static int xiic_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
i2c->prev_msg_tx = false;
/*
- * Enter standard mode only when read length is > 255 bytes or
- * for smbus_block_read transaction
+ * Scan through nmsgs, use dynamic mode when none of the below three
+ * conditions occur. We need standard mode even if one condition holds
+ * true in the entire array of messages in a single transfer.
+ * If read transaction as dynamic mode is broken for delayed reads
+ * in xlnx,axi-iic-2.0 / xlnx,xps-iic-2.00.a IP versions.
+ * If read length is > 255 bytes.
+ * If smbus_block_read transaction.
*/
for (count = 0; count < i2c->nmsgs; count++) {
- if (((i2c->tx_msg[count].flags & I2C_M_RD) &&
- i2c->tx_msg[count].len > MAX_READ_LENGTH_DYNAMIC) ||
- (i2c->tx_msg[count].flags & I2C_M_RECV_LEN)) {
+ broken_read = (i2c->quirks & DYNAMIC_MODE_READ_BROKEN_BIT) &&
+ (i2c->tx_msg[count].flags & I2C_M_RD);
+ max_read_len = (i2c->tx_msg[count].flags & I2C_M_RD) &&
+ (i2c->tx_msg[count].len > MAX_READ_LENGTH_DYNAMIC);
+ smbus_blk_read = (i2c->tx_msg[count].flags & I2C_M_RECV_LEN);
+
+ if (broken_read || max_read_len || smbus_blk_read) {
i2c->dynamic = false;
break;
}
@@ -1108,10 +1126,23 @@ static const struct i2c_adapter xiic_adapter = {
.algo = &xiic_algorithm,
};
+static const struct xiic_version_data xiic_2_00 = {
+ .quirks = DYNAMIC_MODE_READ_BROKEN_BIT,
+};
+
+#if defined(CONFIG_OF)
+static const struct of_device_id xiic_of_match[] = {
+ { .compatible = "xlnx,xps-iic-2.00.a", .data = &xiic_2_00 },
+ {},
+};
+MODULE_DEVICE_TABLE(of, xiic_of_match);
+#endif
+
static int xiic_i2c_probe(struct platform_device *pdev)
{
struct xiic_i2c *i2c;
struct xiic_i2c_platform_data *pdata;
+ const struct of_device_id *match;
struct resource *res;
int ret, irq;
u8 i;
@@ -1121,6 +1152,13 @@ static int xiic_i2c_probe(struct platform_device *pdev)
if (!i2c)
return -ENOMEM;
+ match = of_match_node(xiic_of_match, pdev->dev.of_node);
+ if (match && match->data) {
+ const struct xiic_version_data *data = match->data;
+
+ i2c->quirks = data->quirks;
+ }
+
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
i2c->base = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(i2c->base))
@@ -1201,6 +1239,8 @@ static int xiic_i2c_probe(struct platform_device *pdev)
i2c_new_client_device(&i2c->adap, pdata->devices + i);
}
+ dev_info(&pdev->dev, "mmio %08lx irq %d\n", (unsigned long)res->start, irq);
+
return 0;
err_clk_dis:
@@ -1232,14 +1272,6 @@ static int xiic_i2c_remove(struct platform_device *pdev)
return 0;
}
-#if defined(CONFIG_OF)
-static const struct of_device_id xiic_of_match[] = {
- { .compatible = "xlnx,xps-iic-2.00.a", },
- {},
-};
-MODULE_DEVICE_TABLE(of, xiic_of_match);
-#endif
-
static int __maybe_unused xiic_i2c_runtime_suspend(struct device *dev)
{
struct xiic_i2c *i2c = dev_get_drvdata(dev);
Xilinx I2C IP has two modes of operation, both of which implement I2C transactions. The only difference from sw perspective is the programming sequence for these modes. Dynamic mode -> Simple to program, less number of steps in sequence. Standard mode -> Gives flexibility, more number of steps in sequence. In dynamic mode, during the i2c-read transactions, if there is a delay(> 200us) between the register writes (address & byte count), read transaction fails. On a system with load, this scenario is occurring frequently. To avoid this, switch to standard mode if there is a read request. Added a quirk to identify the IP version effected by this and follow the standard mode. Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com> --- drivers/i2c/busses/i2c-xiic.c | 58 +++++++++++++++++++++++++++-------- 1 file changed, 45 insertions(+), 13 deletions(-)